Common Specs & Procedures
RENEGADE COMMON SPECS & PROCEDURES
| System | Specification/Procedure | ||
|---|---|---|---|
| Air Conditioning | |||
| Service | A/C SYSTEM | ||
| Torque | TORQUE SPECIFICATIONS | ||
| Axle Nut/Hub Nut | |||
| Front | 52 ft. lbs. (70 N.m) plus an additional 60° | ||
| Rear | 52 ft. lbs. + 63° +/- 2° (71 N.m + 63°) | ||
| Battery | BATTERY | ||
| Brakes | |||
| Bleeding Sequence | Base Brakes: STANDARD PROCEDURE
NOTE:
Bleeding procedure for Antilock Brakes is not available from the manufacturer
|
||
| Disc Brakes | |||
| Service Specifications | TECHNICAL SPECIFICATIONS | ||
| Torque | Base Brakes: TORQUE SPECIFICATIONS , Antilock Brakes: TORQUE SPECIFICATIONS | ||
| Drum Brakes | |||
| Service Specifications | N/A | ||
| Torque | N/A | ||
| Charging | |||
| Generator | GENERATOR | ||
| Torque | TORQUE SPECIFICATION | ||
| Drive Belts | |||
| Adjustment | Serpentine belt used, not adjustable. | ||
| Drive Belt Routing | Refer to appropriate "Belt Routing" figure under REMOVAL AND INSTALLATION . | ||
| Engine Cooling | |||
| General Service Specifications | SPECIFICATIONS | ||
| Radiator Cap Pressure | The cap is designed to hold up to 20 psi. | ||
| Thermostat R & I | THERMOSTAT | ||
| Water Pump R & I | PUMP, WATER | ||
| Engine Mechanical | |||
| 1.4L | |||
| Compression | Compression should not be less than 689 kPa (100 psi) and not vary more than 25 percent from cylinder to cylinder. | ||
| Oil Pressure | CHECKING ENGINE OIL PRESSURE | ||
| Overhaul | ENGINE SPECIFICATIONS | ||
| Torque | TORQUE SPECIFICATIONS | ||
| 2.4L | |||
| Compression | Compression should not be less than 689 kPa (100 psi) and not vary more than 25 percent from cylinder to cylinder. | ||
| Oil pressure | Specification is not available from the manufacturer . | ||
| Overhaul | ENGINE SPECIFICATIONS | ||
| Torque | TORQUE SPECIFICATIONS | ||
| Fluid Specifications | See FLUIDS under MAINTENANCE/FLUIDS tab. From within Manager or Service Writer, click the "30/60/90 Interval" or "Maint." button. | ||
| Flywheel/Flex Plate/Drive Plate Torque | |||
| 1.4L | 20 N.m + 50° | ||
| 2.4L | 29 N.m | ||
| Fuel System | |||
| Pressure Specification | |||
| 1.4L | The fuel pressure specification for all engines, including a Non SRT-4 is 407 kPa +/- 34 kPa (59 psi +/- 5 psi). SRT-4 fuel pressure specification is 552 kPa +/- 34 kPa (80 psi +/- 5 psi). | ||
| 2.4L | The fuel pressure specification for all engines, including a Non SRT-4 is 407 kPa +/- 34 kPa (59 psi +/- 5 psi). SRT-4 fuel pressure specification is 552 kPa +/- 34 kPa (80 psi +/- 5 psi). | ||
| Fuel Pressure Test Procedure | |||
| 1.4L | CHECKING THE FUEL DELIVERY SYSTEM (HARD START) | ||
| 2.4L | CHECKING THE FUEL DELIVERY SYSTEM (HARD START) | ||
| Fuel Filter Location | |||
| 1.4L | Fuel filters are integrated into the main fuel pump module. | ||
| 2.4L | Fuel filters are integrated into the main fuel pump module. | ||
| Fuel Filter R & I | |||
| 1.4L | MODULE, FUEL PUMP | ||
| 2.4L | MODULE, FUEL PUMP | ||
| Ignition | |||
| Firing Order & Cylinder Identification | FIRING ORDER & CYLINDER IDENTIFICATION | ||
| Ignition Wires (Resistance) | Coil On Plug | ||
| Ignition Wires (Routing) | Coil On Plug | ||
| Spark Plug | |||
| 1.4L | |||
| Type | Information is not available from the manufacturer. | ||
| Gap | Information is not available from the manufacturer. | ||
| Torque | 18 N.m | ||
| 2.4L | |||
| Type | Information is not available from the manufacturer. | ||
| Gap | Information is not available from the manufacturer. | ||
| Torque | 27 N.m | ||
| Starting | |||
| Starter | STARTER | ||
| Torque | TORQUE SPECIFICATIONS | ||
| Wheel Alignment | |||
| Adjustment Specifications | SPECIFICATIONS | ||
| Torque | Front: TORQUE SPECIFICATIONS , Rear: TORQUE SPECIFICATIONS | ||
| Wheel & Tire | |||
| Wheel Lug Nut Torque | 89 ft. lbs. (120 N.m) | ||