LEMON Manuals: Even more car manuals for everyone
Home >> Subaru >> 2015 >> WRX Base >> Repair and Diagnosis >> External Pages >> Different car >> Section 171 (Continuously Variable Transaxle (CVT) (H4DO)) >> Forward Clutch Assembly >> Installation

Forward Clutch Assembly: Installation

WARNING: This page is about a different car, the 2016 Subaru Outback and 2016 Subaru Legacy. However, it is still accessible from the selected car via links, so may be relevant.
  1. Install the thrust bearing to the converter case.
    NOTE: Face the temper color surface to the converter case side.
    Fig 1: Installing Thrust Bearing To Converter Case
    G08318053Courtesy of SUBARU OF AMERICA, INC.
  2. Install the seal ring to the input shaft.
    NOTE:
    • Use new seal rings.
    • When installing the seal rings, do not expand the seal rings too much.
    • Apply CVTF to the seal rings.
    Fig 2: Locating Input Shaft Seal Rings
    G08318054Courtesy of SUBARU OF AMERICA, INC.
  3. Install the forward clutch assembly to the converter case.
    Fig 3: Identifying Forward Clutch Assembly
    G08318051Courtesy of SUBARU OF AMERICA, INC.
  4. Install the sun gear.
    NOTE: Face the end face of the sun gear to the reverse brake side as shown in the figure.
    Fig 4: Identifying Sun Gear
    G08318056Courtesy of SUBARU OF AMERICA, INC.
  5. Install the thrust bearing to the sun gear.
    NOTE: Face the temper color surface to the reverse brake side.
    Fig 5: Identifying Thrust Bearing And Sun Gear
    G08318057Courtesy of SUBARU OF AMERICA, INC.
  6. Install the planetary carrier.
    Fig 6: Identifying Planetary Carrier
    G08318049Courtesy of SUBARU OF AMERICA, INC.
  7. Install the thrust bearing.
    NOTE: Face the temper color surface to the reverse brake side.
    Fig 7: Identifying Thrust Bearing
    G08318048Courtesy of SUBARU OF AMERICA, INC.
  8. Install the internal gear.
    Fig 8: Identifying Internal Gear
    G08318047Courtesy of SUBARU OF AMERICA, INC.
  9. Install the thrust bearing to the internal gear.
    NOTE: Face the temper color surface to the reverse brake side.
    Fig 9: Identifying Thrust Bearing And Internal Gear
    G08318061Courtesy of SUBARU OF AMERICA, INC.
  10. Select a washer. < Ref. to ADJUSTMENT , Forward Clutch Assembly. >
  11. Install the reverse brake assembly. < Ref. to INSTALLATION , Reverse Brake Assembly. >
  12. Install the primary pulley, secondary pulley and variator chain. < Ref. to INSTALLATION , Primary Pulley and Secondary Pulley. >
  13. Install the reduction drive gear. < Ref. to INSTALLATION , Reduction Drive Gear. >
  14. Install the transmission case. < Ref. to INSTALLATION , Transmission Case. >
  15. Install the transmission control device. < Ref. to INSTALLATION , Transmission Control Device. >
  16. Install the oil strainer and oil pan. < Ref. to INSTALLATION , Oil Pan and Strainer. >
  17. Install the reduction driven gear assembly. < Ref. to INSTALLATION , Reduction Driven Gear. >
  18. Install the transfer driven gear assembly. < Ref. to INSTALLATION , Transfer Driven Gear. >
  19. Install the transfer clutch assembly. < Ref. to INSTALLATION , Transfer Clutch. >
  20. Install the parking pawl. < Ref. to INSTALLATION , Parking Pawl. >
  21. Install the extension case. < Ref. to INSTALLATION , Extension Case. >
  22. Install the inhibitor switch. < Ref. to INSTALLATION , Inhibitor Switch. >
  23. Install the secondary speed sensor. < Ref. to INSTALLATION , Secondary Speed Sensor. >
  24. Install the primary speed sensor. < Ref. to INSTALLATION , Primary Speed Sensor. >
  25. Install the turbine speed sensor. < Ref. to INSTALLATION , Turbine Speed Sensor. >
  26. Install the transmission harness. < Ref. to INSTALLATION , Transmission Harness. >
  27. Install the control valve body. < Ref. to INSTALLATION , Control Valve Body. >
  28. Install the air breather hose. < Ref. to INSTALLATION , Air Breather Hose. >
  29. Install the transmission assembly. < Ref. to INSTALLATION , Automatic Transmission Assembly. >
scientia non olet · About LEMON Manuals