LEMON Manuals: Even more car manuals for everyone
Home >> Scion >> 2009 >> xD Standard >> Repair and Diagnosis >> Engine Mechanical >> Lubrication System >> 2ZR-FE Lubrication >> Oil Pump >> Installation

Oil Pump: Installation

  1. INSTALL OIL PUMP ASSEMBLY 
    1. Install the oil pump assembly with the 3 bolts.

      Torque: 21 N*m (214 kgf*cm, 16 ft.*lbf) 

      Fig 1: Identifying Oil Pump Assembly With Bolts
      G05399742Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
  2. INSTALL NO. 2 OIL PAN SUB-ASSEMBLY  (See REASSEMBLY )
  3. INSTALL NO. 2 CHAIN SUB-ASSEMBLY  (See REASSEMBLY )
  4. INSTALL CRANKSHAFT TIMING GEAR OR SPROCKET  (See REASSEMBLY )
  5. INSTALL NO. 1 CHAIN VIBRATION DAMPER  (See REASSEMBLY )
  6. INSTALL CHAIN SUB-ASSEMBLY  (See REASSEMBLY )
  7. INSTALL CHAIN TENSIONER SLIPPER  (See REASSEMBLY )
  8. INSTALL NO. 2 CHAIN VIBRATION DAMPER  (See REASSEMBLY )
  9. INSTALL TIMING CHAIN OR BELT COVER OIL SEAL 
    1. Using SST, tap in a new oil seal until its surface is flush with the timing gear case edge.

      SST 09223-22010 

      Fig 2: Installing Timing Chain Or Belt Cover Oil Seal
      G05399753Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
    2. Apply a light coat of MP grease to the lip of the oil seal.
      NOTE:
      • Keep the lip free of foreign matter.
      • Do not tap on the oil seal at an angle.
      • Make sure that the oil seal edge does not stick out of the timing chain cover.
  10. INSTALL TIMING CHAIN OR BELT COVER SUB-ASSEMBLY  (See REASSEMBLY )
  11. INSTALL CRANKSHAFT PULLEY  (See REASSEMBLY )
  12. INSTALL NO. 1 CHAIN TENSIONER ASSEMBLY  (See REASSEMBLY )
  13. INSTALL CYLINDER HEAD COVER SUB-ASSEMBLY  (See REASSEMBLY )
  14. INSTALL AIR TUBE ASSEMBLY  (See INSTALLATION )
  15. INSTALL NO. 2 VENTILATION HOSE  (See INSTALLATION )
  16. INSTALL RADIO SETTING CONDENSER  (See INSTALLATION )
  17. INSTALL IGNITION COIL ASSEMBLY  (See INSTALLATION )
  18. INSTALL THERMOSTAT  (See INSTALLATION )
  19. INSTALL WATER INLET  (See INSTALLATION )
  20. INSTALL NO. 3 WATER BY-PASS HOSE  (See INSTALLATION )
  21. INSTALL WATER INLET HOSE  (See INSTALLATION )
  22. INSTALL FAN BELT ADJUSTING BAR  (See INSTALLATION )
  23. INSTALL GENERATOR ASSEMBLY  (See INSTALLATION )
  24. INSTALL OIL LEVEL GAGE GUIDE  (See INSTALLATION )
  25. INSTALL OIL LEVEL DIPSTICK 
  26. INSTALL INTAKE MANIFOLD  (See INSTALLATION )
  27. INSTALL TRANSMISSION OIL FILLER TUBE SUB-ASSEMBLY (for Automatic Transaxle)  (See INSTALLATION )
  28. INSTALL TRANSMISSION OIL LEVEL GAGE SUB-ASSEMBLY (for Automatic Transaxle) 
  29. INSTALL NO. 1 OIL COOLER OUTLET TUBE (for Automatic Transaxle)  (See INSTALLATION )
  30. INSTALL NO. 1 OIL COOLER INLET TUBE (for Automatic Transaxle)  (See INSTALLATION )
  31. INSTALL NO. 2 OIL COOLER TUBE CLAMP (for Automatic Transaxle)  (See INSTALLATION )
  32. INSTALL FRONT SUSPENSION CROSSMEMBER SUB-ASSEMBLY  (See INSTALLATION )
  33. INSTALL ENGINE ASSEMBLY WITH TRANSAXLE  (See INSTALLATION )
  34. INSTALL FRONT AXLE ASSEMBLY LH  (See INSTALLATION )
  35. INSTALL FRONT AXLE ASSEMBLY RH 

    HINT:

    The installation procedure for the RH side is the same as that for the LH side.

  36. INSTALL FRONT LOWER SUSPENSION ARM SUB-ASSEMBLY LH  (See INSTALLATION )
  37. INSTALL FRONT LOWER SUSPENSION ARM SUB-ASSEMBLY RH 

    HINT:

    The installation procedure for the RH side is the same as that for the LH side.

  38. INSTALL FRONT STABILIZER LINK ASSEMBLY LH  (See INSTALLATION )
  39. INSTALL FRONT STABILIZER LINK ASSEMBLY RH 

    HINT:

    The installation procedure for the RH side is the same as that for the LH side.

  40. INSTALL TIE ROD END SUB-ASSEMBLY LH  (See INSTALLATION )
  41. INSTALL TIE ROD END SUB-ASSEMBLY RH 

    HINT:

    The installation procedure for the RH side is the same as that for the LH side.

  42. INSTALL SPEED SENSOR FRONT LH  (See INSTALLATION )
  43. INSTALL SPEED SENSOR FRONT RH 

    HINT:

    The installation procedure for the RH side is the same as that for the LH side.

  44. INSTALL FRONT AXLE SHAFT LH NUT  (See INSTALLATION )
  45. INSTALL FRONT AXLE SHAFT RH NUT 

    HINT:

    The installation procedure for the RH side is the same as that for the LH side.

  46. INSTALL FRONT EXHAUST PIPE ASSEMBLY  (See INSTALLATION )
  47. INSTALL FRONT FLOOR BRACE CENTER  (See INSTALLATION )
  48. INSTALL FRONT CONSOLE BOX  (See INSTALLATION )
  49. INSTALL REAR CONSOLE BOX ASSEMBLY  (See INSTALLATION )
  50. INSTALL CONSOLE BOX CARPET  (See INSTALLATION )
  51. INSTALL CONSOLE BOX REAR COVER  (See INSTALLATION )
  52. INSTALL CONSOLE PANEL UPPER  (See INSTALLATION )
  53. INSTALL SHIFT LEVER KNOB SUB-ASSEMBLY (for Manual Transaxle)  (See INSTALLATION )
  54. INSTALL NO. 1 STEERING COLUMN HOLE COVER SUB-ASSEMBLY  (See INSTALLATION )
  55. INSTALL STEERING SLIDING YOKE SUB-ASSEMBLY  (See INSTALLATION )
  56. INSTALL COLUMN HOLE COVER SILENCER SHEET  (See INSTALLATION )
  57. INSTALL CLUTCH RELEASE CYLINDER ASSEMBLY (for Manual Transaxle)  (See INSTALLATION )
  58. CONNECT FUEL TUBE SUB-ASSEMBLY  (See INSTALLATION )
  59. CONNECT HEATER WATER INLET HOSE A  (See INSTALLATION )
  60. CONNECT HEATER WATER OUTLET HOSE A(FROM HEATER UNIT)  (See INSTALLATION )
  61. CONNECT ENGINE WIRE  (See INSTALLATION )
  62. INSTALL NO. 1 FUEL VAPOR FEED HOSE  (See INSTALLATION )
  63. INSTALL UNION TO CHECK VALVE HOSE  (See INSTALLATION )
  64. INSTALL TRANSMISSION CONTROL CABLE ASSEMBLY (for Automatic Transaxle)  (See INSTALLATION )
  65. INSTALL TRANSMISSION CONTROL CABLE ASSEMBLY (for Manual Transaxle)  (See INSTALLATION )
  66. INSTALL WITH PULLEY COMPRESSOR ASSEMBLY  (See INSTALLATION )
  67. INSTALL RADIATOR ASSEMBLY  (See INSTALLATION )
  68. INSTALL UPPER RADIATOR SUPPORT SUB-ASSEMBLY  (See INSTALLATION )
  69. INSTALL UPPER RADIATOR SUPPORT ABSORBER  (See REASSEMBLY )
  70. INSTALL NO. 1 COOLER COVER  (See INSTALLATION )
  71. INSTALL HOOD LOCK ASSEMBLY  (See INSTALLATION )
  72. CONNECT NO. 2 OIL COOLER INLET HOSE (for Automatic Transaxle)  (See INSTALLATION )
  73. CONNECT NO. 1 OIL COOLER OUTLET HOSE (for Automatic Transaxle)  (See INSTALLATION )
  74. INSTALL FRONT BUMPER COVER  (See INSTALLATION )
  75. CONNECT NO. 1 RADIATOR HOSE  (See INSTALLATION )
  76. INSTALL NO. 2 RADIATOR HOSE  (See INSTALLATION )
  77. INSTALL FAN AND GENERATOR V BELT  (See INSTALLATION )
  78. ADJUST FAN AND GENERATOR V BELT  (See INSTALLATION )
  79. INSPECT FAN AND GENERATOR V BELT  (See INSTALLATION )
  80. INSTALL NO. 2 CYLINDER HEAD COVER  (See INSTALLATION )
  81. INSTALL BATTERY CARRIER  (See INSTALLATION )
  82. INSTALL AIR CLEANER BRACKET  (See INSTALLATION )
  83. INSTALL AIR CLEANER ASSEMBLY  (See INSTALLATION )
  84. INSTALL OUTER COWL TOP PANEL  (See INSTALLATION )
  85. INSTALL FRONT AIR SHUTTER SEAL RH  (See INSTALLATION )
  86. INSTALL FRONT WIPER MOTOR AND LINK  (See INSTALLATION )
  87. INSTALL COWL TOP VENTILATOR LOUVER LH  (See INSTALLATION )
  88. INSTALL COWL TOP VENTILATOR LOUVER SUB-ASSEMBLY  (See INSTALLATION )
  89. INSTALL HOOD TO COWL TOP SEAL  (See INSTALLATION )
  90. INSTALL FRONT WIPER ARM AND BLADE ASSEMBLY LH  (See INSTALLATION )
  91. INSTALL FRONT WIPER ARM AND BLADE ASSEMBLY RH  (See INSTALLATION )
  92. INSTALL FRONT WIPER ARM HEAD CAP  (See INSTALLATION )
  93. INSTALL BATTERY TRAY 
  94. INSTALL BATTERY  (See INSTALLATION )
  95. ADD ENGINE COOLANT  (See REPLACEMENT )
  96. ADD ENGINE OIL  (See REPLACEMENT  )
  97. INSPECT FOR FUEL LEAK 
  98. INSPECT FOR ENGINE OIL LEAK 
  99. INSPECT FOR EXHAUST GAS LEAK 
  100. INSPECT FOR ENGINE COOLANT LEAK  (See ON-VEHICLE INSPECTION )
  101. INSTALL ENGINE UNDER COVER RH 
  102. INSTALL ENGINE UNDER COVER LH 
  103. INSTALL FRONT WHEELS  (See INSTALLATION )
  104. INSPECT IGNITION TIMING  (See ON-VEHICLE INSPECTION )
  105. INSPECT ENGINE IDLING SPEED  (See ON-VEHICLE INSPECTION )
  106. INSPECT CO/HC  (See ON-VEHICLE INSPECTION )
  107. INSPECT FRONT WHEEL ALIGNMENT 

    (See ADJUSTMENT )

  108. INSPECT ABS SENSOR SIGNAL 

    (See TEST MODE PROCEDURE )

  109. INSPECT VSC SENSOR SIGNAL 

    (See TEST MODE PROCEDURE )

scientia non olet · About LEMON Manuals