Section 1 (Automatic Transaxle On-Vehicle Service - With Diagnostics)

• Service Specifications
• Lubricant
• Automatic Transaxle Diagnosis
  • Diagnostic Troubleshooting Flow
  • Introduction To A/T Diagnosis
  • A/T Diagnostic Troubleshooting Strategy
  • Primary Check
  • Diagnosis Function
  • Freeze Frame Data Reference Table
  • How To Initialize A/T Learned Value
    • Purpose
    • Initialization Procedure
  • Fail-Safe/Backup Function
    • Notes
    • Fail-Safe Function
  • Road Test
    • Notes
    • P-range test
    • Select time lag
  • Torque Converter Stall Test
  • Hydraulic Pressure Tests
  • Shift Pattern
    • Upshift Pattern
    • Downshift Pattern
  • Torque Converter Clutch Control
    • In 6th range
    • In 5th range
    • In 4th range
    • In 3rd range
  • Diagnostic Trouble Code Chart
  • Check Chart For Trouble Symptoms
  • Diagnostic Trouble Code Procedures
    • DTC P0705: Transmission Range Switch System
      • Descriptions Of Monitor Methods
      • Monitor Execution
      • Monitor Execution Conditions (Other Monitor And Sensor)
        • Other Monitor (There is no temporary DTC stored in memory for the item monitored below)
        • Sensor (The sensor below is determined to be normal)
      • LOGIC FLOW CHARTS (Monitor Sequence)
      • DTC Set Conditions
        • Check Conditions
        • Judgment Criteria
      • OBD-II Drive Cycle Pattern
      • Probable Causes
      • Diagnosis
    • DTC P0712: Transmission Fluid Temperature Sensor System (Short Circuit)
      • Descriptions Of Monitor Methods
      • Monitor Execution
      • Monitor Execution Conditions (Other Monitor And Sensor)
        • Other Monitor (There is no temporary DTC stored in memory for the item monitored below)
        • Sensor (The sensor below is determined to be normal)
      • LOGIC FLOW CHARTS (Monitor Sequence)
      • DTC Set Conditions
        • Check Conditions
        • Judgment Criteria
      • OBD-II Drive Cycle Pattern
      • Probable Causes
      • Diagnosis
    • DTC P0713: Transmission Fluid Temperature Sensor System (Open Circuit)
      • Descriptions Of Monitor Methods
      • Monitor Execution
      • Monitor Execution Conditions (Other Monitor And Sensor)
        • Other Monitor (There is no temporary DTC set in memory for the item monitored below)
        • Sensor (The sensor below is determined to be normal)
      • LOGIC FLOW CHARTS (Monitor Sequence)
      • DTC Set Conditions
        • Check Conditions
        • Judgment Criteria
      • OBD-II Drive Cycle Pattern
      • Probable Causes
      • Diagnosis
    • DTC P0715: Input Shaft Speed Sensor System
      • Descriptions Of Monitor Methods
      • Monitor Execution
      • Monitor Execution Conditions (Other Monitor And Sensor)
        • Other Monitor (There is no temporary DTC stored in memory for the item monitored below)
        • Sensor (The sensor below is determined to be normal)
      • LOGIC FLOW CHARTS (Monitor Sequence)
      • DTC Set Conditions
        • Check Conditions
        • Judgment Criteria
      • OBD-II Drive Cycle Pattern
      • Probable Causes
      • Diagnosis
    • DTC P0720: Output Shaft Speed Sensor System
      • Descriptions Of Monitor Methods
      • Monitor Execution
      • Monitor Execution Conditions (Other Monitor And Sensor)
        • Other Monitor (There is no temporary DTC stored in memory for the item monitored below)
        • Sensor (The sensor below is determined to be normal)
      • LOGIC FLOW CHARTS (Monitor Sequence)
      • DTC Set Conditions
        • Check Conditions
        • Judgment Criteria
      • OBD-II Drive Cycle Pattern
      • Probable Causes
      • Diagnosis
    • DTC P0729, P0732, P0733, P0734, P0735: 6th, 2nd, 3rd, 4th, 5th Gear Ratio
      • LOGIC FLOW CHARTS (Monitor Sequence)
      • Descriptions Of Monitor Methods <DTC P0729>
      • Monitor Execution <DTC P0729>
      • Monitor Execution Conditions (Other Monitor And Sensor)
        • Other Monitor (There is no temporary DTC stored in memory for the item monitored below)
        • Sensor (The sensor below is determined to be normal)
      • DTC Set Conditions
        • Check Conditions
        • Judgment Criteria
      • OBD-II Drive Cycle Pattern <DTC P0729>
      • Descriptions Of Monitor Methods <DTC P0732>
      • Monitor Execution <DTC P0732>
      • Monitor Execution Conditions (Other Monitor And Sensor)
        • Other Monitor (There is no temporary DTC stored in memory for the item monitored below)
        • Sensor (The sensor below is determined to be normal)
      • DTC Set Conditions
        • Check Conditions
        • Judgment Criteria
      • OBD-II Drive Cycle Pattern <DTC P0732>
      • Descriptions Of Monitor Methods <DTC P0733>
      • Monitor Execution <DTC P0733>
      • Monitor Execution Conditions (Other Monitor And Sensor)
        • Other Monitor (There is no temporary DTC stored in memory for the item monitored below)
        • Sensor (The sensor below is determined to be normal)
      • DTC Set Conditions
        • Check Conditions
        • Judgment Criteria
      • OBD-II Drive Cycle Pattern <DTC P0733>
      • Descriptions Of Monitor Methods <DTC P0734>
      • Monitor Execution <DTC P0734>
      • Monitor Execution Conditions (Other Monitor And Sensor)
        • Other Monitor (There is no temporary DTC stored in memory for the item monitored below)
        • Sensor (The sensor below is determined to be normal)
      • DTC Set Conditions
        • Check Conditions
        • Judgment Criteria
      • OBD-II Drive Cycle Pattern <DTC P0734>
      • Descriptions Of Monitor Methods <DTC P0735>
      • Monitor Execution <DTC P0735>
      • Monitor Execution Conditions (Other Monitor And Sensor)
        • Other Monitor (There is no temporary DTC stored in memory for the item monitored below)
        • Sensor (The sensor below is determined to be normal)
      • DTC Set Conditions
        • Check Conditions
        • Judgment Criteria
      • OBD-II Drive Cycle Pattern <DTC P0735>
      • Probable Causes
      • Diagnosis
    • DTC P0731: 1st Gear Incorrect Ratio
      • Descriptions Of Monitor Methods
      • Monitor Execution
      • Monitor Execution Conditions (Other Monitor And Sensor)
        • Other Monitor (There is no temporary DTC stored in memory for the item monitored below)
        • Sensor (The sensor below is determined to be normal)
      • LOGIC FLOW CHARTS (Monitor Sequence)
      • DTC Set Conditions
        • Check Conditions
        • Judgment Criteria
      • OBD-II Drive Cycle Pattern
      • Probable Causes
      • Diagnosis
    • DTC P0736: Reverse Gear Incorrect Ratio
      • Descriptions Of Monitor Methods
      • Monitor Execution
      • Monitor Execution Conditions (Other Monitor And Sensor)
        • Other Monitor (There is no temporary DTC stored in memory for the item monitored below)
        • Sensor (The sensor below is determined to be normal)
      • LOGIC FLOW CHARTS (Monitor Sequence)
      • DTC Set Conditions
        • Check Conditions
        • Judgment Criteria
      • OBD-II Drive Cycle Pattern
      • Probable Causes
      • Diagnosis
    • DTC P0741: Damper Clutch System (Stuck off), DTC P0742 Damper Clutch System (Stuck on)
      • Descriptions Of Monitor Methods <P0741>
      • Monitor Execution <P0741>
      • Monitor Execution Conditions (Other Monitor And Sensor)
        • Other Monitor (There is no temporary DTC stored in memory for the item monitored below)
        • Sensor (The sensor below is determined to be normal)
      • LOGIC FLOW CHARTS (Monitor Sequence) <P0741>
      • DTC Set Conditions
        • Check Conditions
        • Judgment Criteria
      • OBD-II Drive Cycle Pattern <P0741>
      • Descriptions Of Monitor Methods <P0742>
      • Monitor Execution <P0742>
      • Monitor Execution Conditions (Other Monitor And Sensor)
        • Other Monitor (There is no temporary DTC stored in memory for the item monitored below)
        • Sensor (The sensor below is determined to be normal)
      • LOGIC FLOW CHARTS (Monitor Sequence) <P0742>
      • DTC Set Conditions
        • Check Conditions
        • Judgment Criteria
      • OBD-II Drive Cycle Pattern <P0742>
      • Probable Causes
      • Diagnosis
    • DTC P0815: Paddle Shift Switch (Up) System
      • Descriptions Of Monitor Methods
      • Probable Causes
      • Diagnosis
    • DTC P0816: Paddle Shift Switch (Down) System
      • Descriptions Of Monitor Methods
      • Probable Causes
      • Diagnosis
    • DTC P0846: 2-6 Brake Pressure Switch System
      • Descriptions Of Monitor Methods
      • Monitor Execution
      • Monitor Execution Conditions (Other Monitor And Sensor)
        • Other Monitor (There is no temporary DTC stored in memory for the item monitored below)
        • Sensor (The sensor below is determined to be normal)
      • LOGIC FLOW CHARTS (Monitor Sequence)
      • DTC Set Conditions
        • Check Conditions <Stuck-off>
        • Judgment Criteria <Stuck-off>
        • Check Conditions <Stuck-on>
        • Judgment Criteria <Stuck-on>
      • OBD-II Drive Cycle Pattern
      • Probable Causes
      • Diagnosis
    • DTC P0876: High Clutch Pressure Switch System
      • Descriptions Of Monitor Methods
      • Monitor Execution
      • Monitor Execution Conditions (Other Monitor And Sensor)
        • Other Monitor (There is no temporary DTC stored in memory for the item monitored below)
        • Sensor (The sensor below is determined to be normal)
      • LOGIC FLOW CHARTS (Monitor Sequence)
      • DTC Set Conditions
        • Check Conditions <Stuck-off>
        • Judgment Criteria <Stuck-off>
        • Check Conditions <Stuck-on>
        • Judgment Criteria <Stuck-on>
      • OBD-II Drive Cycle Pattern
      • Probable Causes
      • Diagnosis
    • DTC P0893: Interlock Detection
      • Descriptions Of Monitor Methods
      • Monitor Execution
      • Monitor Execution Conditions (Other Monitor And Sensor)
        • Other Monitor (There is no temporary DTC stored in memory for the item monitored below)
        • Sensor (The sensor below is determined to be normal)
      • LOGIC FLOW CHARTS (Monitor Sequence)
      • DTC Set Conditions
        • Check Conditions
        • Judgment Criteria
      • OBD-II Drive Cycle Pattern
      • Probable Causes
      • Diagnosis
    • DTC P0962: Line Pressure Linear Solenoid Valve System (Short circuit); DTC P0963: Line Pressure Linear Solenoid Valve System (Open circuit)
      • Descriptions Of Monitor Methods
      • Monitor Execution
      • Monitor Execution Conditions (Other Monitor And Sensor)
        • Other Monitor (There is no temporary DTC stored in memory for the item monitored below)
        • Sensor (The sensor below is determined to be normal)
      • LOGIC FLOW CHARTS (Monitor Sequence)
      • DTC Set Conditions
        • Check Conditions <P0962>
        • Judgment Criteria <P0962>
        • Check Conditions <P0963>
        • Judgment Criteria <P0963>
      • OBD-II Drive Cycle Pattern
      • Probable Causes
      • Diagnosis
    • DTC P0973: Low Clutch Linear Solenoid Valve System (Short circuit); DTC P0974: Low Clutch Linear Solenoid Valve System (Open circuit)
      • Descriptions Of Monitor Methods
      • Monitor Execution
      • Monitor Execution Conditions (Other Monitor And Sensor)
        • Other Monitor (There is no temporary DTC stored in memory for the item monitored below)
        • Sensor (The sensor below is determined to be normal)
      • LOGIC FLOW CHARTS (Monitor Sequence)
      • DTC Set Conditions
        • Check Conditions <P0973>
        • Judgment Criteria <P0973>
        • Check Conditions <P0974>
        • Judgment Criteria <Circuit continuity open>
      • OBD-II Drive Cycle Pattern
      • Probable Causes
      • Diagnosis
    • DTC P0976: 2-6 Brake Linear Solenoid Valve System (Short circuit); DTC P0977: 2-6 Brake Linear Solenoid Valve System (Open circuit)
      • Descriptions Of Monitor Methods
      • Monitor Execution
      • Monitor Execution Conditions (Other Monitor And Sensor)
        • Other Monitor (There is no temporary DTC stored in memory for the item monitored below)
        • Sensor (The sensor below is determined to be normal)
      • LOGIC FLOW CHARTS (Monitor Sequence)
      • DTC Set Conditions
        • Check Conditions <P0976>
        • Judgment Criteria <P0976>
        • Check Conditions <P0977>
        • Judgment Criteria <P0977>
      • OBD-II Drive Cycle Pattern
      • Probable Causes
      • Diagnosis
    • DTC P0979: 3-5 Reverse Clutch Linear Solenoid Valve System (Short circuit); DTC P0980: 3-5 Reverse Clutch Linear Solenoid Valve System (Open circuit)
      • Descriptions Of Monitor Methods
      • Monitor Execution
      • Monitor Execution Conditions (Other Monitor And Sensor)
        • Other Monitor (There is no temporary DTC stored in memory for the item monitored below)
        • Sensor (The sensor below is determined to be normal)
      • LOGIC FLOW CHARTS (Monitor Sequence)
      • DTC Set Conditions
        • Check Conditions <P0979>
        • Judgment Criteria <P0979>
        • Check Conditions <P0980>
        • Judgment Criteria <P0980>
      • OBD-II Drive Cycle Pattern
      • Probable Causes
      • Diagnosis
    • DTC P0982: High Clutch Linear Solenoid Valve System (Short circuit); DTC P0983: High Clutch Linear Solenoid Valve System (Open circuit)
      • Descriptions Of Monitor Methods
      • Monitor Execution
      • Monitor Execution Conditions (Other Monitor And Sensor)
        • Other Monitor (There is no temporary DTC stored in memory for the item monitored below)
        • Sensor (The sensor below is determined to be normal)
      • LOGIC FLOW CHARTS (Monitor Sequence)
      • DTC Set Conditions
        • Check Conditions <P0982>
        • Judgment Criteria <P0982>
        • Check Conditions <P0983>
        • Judgment Criteria <P0983>
      • OBD-II Drive Cycle Pattern
      • Probable Causes
      • Diagnosis
    • DTC P0988: Low-Reverse Brake Pressure Switch System
      • Descriptions Of Monitor Methods
      • Monitor Execution
      • Monitor Execution Conditions (Other Monitor And Sensor)
        • Other Monitor (There is no temporary DTC stored in memory for the item monitored below)
        • Sensor (The sensor below is determined to be normal)
      • LOGIC FLOW CHARTS (Monitor Sequence)
      • DTC Set Conditions
        • Check Conditions <Stuck-off>
        • Judgment Criteria <Stuck-off>
        • Check Conditions <Stuck-on>
        • Judgment Criteria <Stuck-on>
      • OBD-II Drive Cycle Pattern
      • Probable Causes
      • Diagnosis
    • DTC P0998: Low Clutch Shift Solenoid Valve System (Short circuit); DTC P0999: Low Clutch Shift Solenoid Valve System (Open circuit)
      • Descriptions Of Monitor Methods
      • Monitor Execution
      • Monitor Execution Conditions (Other Monitor And Sensor)
        • Other Monitor (There is no temporary DTC stored in memory for the item monitored below)
        • Sensor (The sensor below is determined to be normal)
      • LOGIC FLOW CHARTS (Monitor Sequence) <P0998>
      • LOGIC FLOW CHARTS (Monitor Sequence) <P0999>
      • DTC Set Conditions
        • Check Conditions <P0998>
        • Judgment Criteria <P0998>
        • Check Conditions <P0999>
        • Judgment Criteria <P0999>
      • OBD-II Drive Cycle Pattern
      • Probable Causes
      • Diagnosis
    • DTC P099B: Low-Reverse Brake Shift Solenoid Valve System (Short circuit); DTC P099C: Low-Reverse Brake Shift Solenoid Valve System (Open circuit)
      • DTC Set Conditions
        • Overview
        • Check Conditions <Circuit continuity ground>
        • Judgment Criteria <Circuit continuity ground>
        • Check Conditions <Circuit continuity open>
        • Judgment Criteria <Circuit continuity open>
      • Monitor Execution
      • Monitor Execution Conditions (Other Monitor And Sensor)
        • Other Monitor (There is no temporary DTC stored in memory for the item monitored below)
        • Sensor (The sensor below is determined to be normal)
      • LOGIC FLOW CHARTS (Monitor Sequence) <P099B>
      • LOGIC FLOW CHARTS (Monitor Sequence) <P0999>
      • OBD-II Drive Cycle Pattern
      • Probable Causes
      • Diagnosis
    • DTC P1637: Memory Backup System
      • Diagnostic Function
      • Descriptions Of Monitor Methods
      • Monitor Execution
      • Monitor Execution Conditions (Other Monitor And Sensor)
        • Other Monitor (There is no temporary DTC stored in memory for the item monitored below)
        • Sensor (The sensor below is determined to be normal)
      • LOGIC FLOW CHARTS (Monitor Sequence)
      • DTC Set Conditions
        • Judgment Criteria
      • OBD-II Drive Cycle Pattern
      • Probable Causes
      • Diagnostic Procedure
    • DTC P1705: Throttle Position Sensor Information (Engine)
      • Descriptions Of Monitor Methods
      • Monitor Execution
      • Monitor Execution Conditions (Other Monitor And Sensor)
        • Other Monitor (There is no temporary DTC stored in memory for the item monitored below)
        • Sensor (The sensor below is determined to be normal)
      • LOGIC FLOW CHARTS (Monitor Sequence)
      • DTC Set Conditions
        • Check Conditions
        • Judgment Criteria
      • OBD-II Drive Cycle Pattern
      • Probable Causes
      • Diagnosis
    • DTC P1706: Accelerator Pedal Position Sensor Information
      • DTC Set Conditions
        • Overview
        • Check Conditions
        • Judgment Criteria
      • Monitor Execution
      • Monitor Execution Conditions (Other Monitor And Sensor)
        • Other Monitor (There is no temporary DTC stored in memory for the item monitored below)
        • Sensor (The sensor below is determined to be normal)
      • LOGIC FLOW CHARTS (Monitor Sequence)
      • OBD-II Drive Cycle Pattern
      • Probable Causes
      • Diagnosis
    • DTC P1773: ASC Information
      • Descriptions Of Monitor Methods
      • Monitor Execution
      • Monitor Execution Conditions (Other Monitor And Sensor)
        • Other Monitor (There is no temporary DTC stored in memory for the item monitored below)
        • Sensor (The sensor below is determined to be normal)
      • LOGIC FLOW CHARTS (Monitor Sequence)
      • DTC Set Conditions
        • Check Conditions
        • Judgment Criteria
      • OBD-II Drive Cycle Pattern
      • Probable Causes
      • Diagnosis
    • DTC P1796: Idle-N control function failure
      • Descriptions Of Monitor Methods
      • Probable Causes
      • Diagnosis
    • DTC P2763: Lock-up and Low-reverse Brake Linear Solenoid Valve System (Open circuit); DTC P2764: Lock-up and Low-reverse Brake Linear Solenoid Valve System (Short circuit)
      • Descriptions Of Monitor Methods
      • Monitor Execution
      • Monitor Execution Conditions (Other Monitor And Sensor)
        • Other Monitor (There is no temporary DTC stored in memory for the item monitored below)
        • Sensor (The sensor below is determined to be normal)
      • LOGIC FLOW CHARTS (Monitor Sequence)
      • DTC Set Conditions
        • Check Conditions <P2763>
        • Judgment Criteria <P2763>
        • Check Conditions <P2764>
        • Judgment Criteria <P2764>
      • OBD-II Drive Cycle Pattern
      • Probable Causes
      • Diagnosis
    • DTC U0001: Malfunction of CAN communication circuit (Bus off)
      • Diagnostic Function
      • Descriptions Of Monitor Methods
      • Monitor Execution
      • Monitor Execution Conditions (Other Monitor And Sensor)
        • Other Monitor (There is no temporary DTC stored in memory for the item monitored below)
        • Sensor (The sensor below is determined to be normal)
      • LOGIC FLOW CHARTS (Monitor Sequence)
      • DTC Set Conditions
        • Check Conditions
        • Judgment Criteria
      • OBD-II Drive Cycle Pattern
      • Probable Causes
      • Diagnosis
    • DTC U0100: CAN time-out error (Engine)
      • Diagnostic Function
      • Descriptions Of Monitor Methods
      • Monitor Execution
      • Monitor Execution Conditions (Other Monitor And Sensor)
        • Other Monitor (There is no temporary DTC stored in memory for the item monitored below)
        • Sensor (The sensor below is determined to be normal)
      • LOGIC FLOW CHARTS (Monitor Sequence)
      • DTC Set Conditions
        • Check Conditions
        • Judgment Criteria
      • OBD-II Drive Cycle Pattern
      • Probable Causes
      • Diagnosis
    • DTC U0121: CAN time-out error (ASC)
      • Diagnostic Function
      • DTC Set Conditions
        • Judgment Criteria
      • Probable Causes
      • Diagnosis
    • DTC U0141: CAN time-out error (ETACS)
      • Diagnostic Function
      • DTC Set Conditions
        • Judgment Criteria
      • Probable Causes
      • Diagnosis
    • DTC U0317: CAN time-out error (EPB)
      • Diagnostic Function
      • DTC Set Conditions
        • Judgment Criteria
      • Probable Causes
      • Diagnosis
  • Symptom Procedures
    • Inspection Procedure 1: TCM cannot communicate with scan tool (M.U.T.-III)
      • Symptoms
      • Probable Causes
      • Diagnostic Procedure
    • Inspection Procedure 2: The vehicle does not run at any range
      • Probable Causes
      • Diagnosis
    • Inspection Procedure 3: The vehicle does not run at the "D" or the "R" range
      • Probable Causes
      • Diagnosis
    • Inspection Procedure 4: The acceleration is poor
      • Probable Causes
      • Diagnosis
    • Inspection Procedure 5: The vehicle moves at the "N" range
      • Probable Causes
      • Diagnosis
    • Inspection Procedure 6: Gears cannot be shifted at all, or a certain gear shift (1st to 2nd, 2nd to 3rd, etc.) is not made
      • Probable Causes
      • Diagnosis
    • Inspection Procedure 7: The torque converter is not locked up
      • Probable Causes
      • Diagnosis
    • Inspection Procedure 8: The clutch slips when the vehicle starts or during gear shift
      • Probable Causes
      • Diagnosis
    • Inspection Procedure 9: The engine brake is not applied
      • Probable Causes
      • Diagnosis
    • Inspection Procedure 10: The shift shock is large at a certain gear shift. (1st to 2nd, 2nd to 3rd, etc.)
      • Probable Causes
      • Diagnosis
    • Inspection Procedure 11: The select shock is large when the selector lever position is shifted from "N" to "D", and "N" to "R."
      • Probable Causes
      • Diagnosis
    • Inspection Procedure 12: Abnormal sound occurs during idling
      • Probable Causes
      • Diagnosis
    • Inspection Procedure 13: Abnormal sound occurs during driving
      • Probable Causes
      • Diagnosis
    • Inspection Procedure 14: Abnormal sound occurs during gear shift
      • Probable Causes
      • Diagnosis
    • Inspection Procedure 15: Engine stall
      • Probable Causes
      • Diagnosis
    • Inspection Procedure 16: Oil leaks from the air breather
      • Probable Causes
      • Diagnosis
    • Inspection Procedure 17: The starter does not rotate at the "P" or "N" range. (The engine does not start.)
      • Probable Causes
      • Diagnosis
  • Data List Reference Table
  • Check At Engine TCM Terminal
• Diagnosis
  • Standard Flow Of Diagnostic Troubleshooting
  • Precautions For Diagnosis
  • Indicator Check
  • Diagnostic Function
    • When the system fails
    • When the S-AWC system oil is too hot
    • Fail-safe function
      • Notes
      • On-Board Diagnostics
      • How To Connect The Scan Tool (M.U.T.-III)
      • How To Read And Erase Diagnostic Trouble Codes
      • How To Read Data List
      • How To Perform Actuator Test
      • How To Diagnose The Can Bus Lines
  • Freeze Frame Data Reference Table
  • Diagnostic Trouble Code Chart
  • Trouble Symptom Chart
  • Diagnostic Trouble Code Procedures
    • DTC C100A: FL Wheel Speed Sensor Circuit; DTC C1015: FR Wheel Speed Sensor Circuit; DTC C1020: RL Wheel Speed Sensor Circuit; DTC C102B: RR Wheel Speed Sensor Circuit
      • Notes
      • Operation
      • DTC Set Condition
      • Probable Causes
      • Diagnostic Procedure
    • DTC C1011: FL Wheel Speed Sensor Signal; DTC C101C: FR Wheel Speed Sensor Signal; DTC C1027: RL Wheel Speed Sensor Signal; DTC C1032: RR Wheel Speed Sensor Signal
      • Notes
      • Operation
      • DTC Set Condition
      • Probable Causes
      • Diagnostic Procedure
    • DTC C1014: FL Wheel Speed Sensor Performance; DTC C101F: FR Wheel Speed Sensor Performance; DTC C102A: RL Wheel Speed Sensor Performance; DTC C1035: RR Wheel Speed Sensor Performance
      • Notes
      • Operation
      • DTC Set Condition
      • Probable Causes
      • Diagnostic Procedure
    • DTC C1078: Tire Revolutions Range
      • Notes
      • Operation
      • DTC Set Condition
      • Probable Causes
      • Diagnostic Procedure
    • DTC C1219: Steering Wheel Sensor Signal
      • Notes
      • Operation
      • DTC Set Conditions
      • Probable Causes
      • Diagnostic Procedure
    • DTC C121A: Steering Wheel Sensor Initialization
      • Notes
      • Operation
      • DTC Set Condition
      • Probable Causes
      • Diagnostic Procedure
    • DTC C123C: Sensor Cluster Malfunction
      • Notes
      • Operation
      • DTC Set Conditions
      • Probable Causes
      • Diagnostic Procedure
    • DTC C1242: Straight G Sensor Signal
      • Notes
      • Operation
      • DTC Set Conditions
      • Probable Causes
      • Diagnostic Procedure
    • DTC C1610: Electronic Controlled Coupling Solenoid Power Supply Relay Fails
      • Operation
      • DTC Set Conditions
      • Probable Causes
      • Diagnostic Procedure
    • DTC C1613: Drive Mode Selector Stuck
      • Operation
      • DTC Set Condition
      • Probable Causes
      • Diagnostic Procedure
    • DTC C1614: Parking Brake Switch Stuck On
      • Notes
      • Operation
      • DTCSET Condition
      • Probable Causes
      • Diagnostic Procedure
    • DTC C1615: Brake Control Prohibited Request
      • Notes
      • Operation
      • DTC Set Condition
      • Probable Causes
      • Diagnostic Procedure
    • DTC C1616: Cranking Signal Stuck
      • Notes
      • Operation
      • DTC Set Condition
      • Probable Causes
      • Diagnostic Procedure
    • DTC C161F: Electronic Controlled Coupling Solenoid (Front) Protection
      • Notes
      • Operation
      • DTC Set Condition
      • Probable Causes
      • Diagnostic Procedure
    • DTC C1621: Electronic Controlled Coupling Solenoid (Center) Protection
      • Notes
      • Operation
      • DTC Set Condition
      • Probable Causes
      • Diagnostic Procedure
    • DTC C1623: Brake Control Abnormality
      • Notes
      • Operation
      • DTC Set Condition
      • Probable Causes
      • Diagnostic Procedure
    • DTC C1624: AWC-ECU Internal
      • Operation
      • Diagnostic Trouble Code Set Condition
      • Probable Causes
    • DTC C1626: Electronic Controlled Coupling Solenoid Voltage Fails
      • Operation
      • DTC Set Condition
      • Probable Causes
      • Diagnostic Procedure
    • DTC C1627: Abnormal Electronic Control Solenoid (Front) Current
      • Operation
      • DTC Set Conditions
      • Probable Causes
      • Diagnostic Procedure
    • DTC C1628: Electronic Controlled Coupling Solenoid (Center) Current Fails
      • Operation
      • DTC Set Conditions
      • Probable Causes
      • Diagnostic Procedure
    • DTC C1629: ASC Timeout
      • Notes
      • Operation
      • DTC Set Condition
      • Probable Causes
      • Diagnostic Procedure
    • DTC C1630: Steering Wheel Sensor Timeout
      • Notes
      • Operation
      • DTC Set Condition
      • Probable Causes
      • Diagnostic Procedure
    • DTC C1631: ETACS Timeout
      • Notes
      • Operation
      • DTC Set Condition
      • Probable Causes
      • Diagnostic Procedure
    • DTC C1632: Engine Timeout
      • Notes
      • Operation
      • DTC Set Conditions
      • Probable Causes
      • Diagnostic Procedure
    • DTC C1633: T/M Timeout
      • Notes
      • Operation
      • DTC Set Condition
      • Probable Causes
      • Diagnostic Procedure
    • DTC C1634: EPS Timeout
      • Notes
      • Operation
      • DTC Set Conditions
      • Probable Causes
      • Diagnostic Procedure
    • DTC C1635: EPS control prohibited request
      • Notes
      • Operation
      • DTC Set Conditions
      • Probable Causes
      • Diagnostic Procedure
    • DTC C1707: Implausible Coding Data
      • Notes
      • Operation
      • DTC Set Condition
      • Probable Causes
      • Diagnostic Procedure
    • DTC C2100: Power Supply Low Voltage
      • Notes
      • Operation
      • DTC Set Conditions
      • Probable Causes
      • Diagnostic Procedure
    • DTC C2101: Power Supply High Voltage
      • Operation
      • DTC Set Conditions
      • Probable Causes
      • Diagnostic Procedure
    • DTC C2205: Steering Wheel Sensor Internal Error
      • Notes
      • Operation
      • DTC Set Condition
      • Probable Causes
      • Diagnostic Procedure
    • DTC U0100: Engine CAN Timeout
      • Notes
      • Operation
      • DTC Set Condition
      • Probable Causes
      • Diagnostic Procedure
    • DTC U0101: T/M CAN Timeout
      • Notes
      • Operation
      • DTC Set Condition
      • Probable Causes
      • Diagnostic Procedure
    • DTC U0121: ASC CAN Timeout
      • Notes
      • Operation
      • DTC Set Condition
      • Probable Causes
      • Diagnostic Procedure
    • DTC U0126: Steering Wheel Sensor CAN Timeout
      • Notes
      • Operation
      • DTC Set Condition
      • Probable Causes
      • Diagnostic Procedure
    • DTC U0131: EPS CAN timeout
      • Notes
      • Operation
      • DTC Set Condition
      • Probable Causes
      • Diagnostic Procedure
    • DTC U0141: ETACS CAN Timeout
      • Notes
      • Operation
      • DTC Set Condition
      • Probable Causes
      • Diagnostic Procedure
    • DTC U0317: CAN time-out error (EPB)
      • Diagnostic Function
      • DTC Set Conditions
        • Judgment Criteria
      • Probable Causes
      • Diagnosis
    • DTC U0401: Engine CAN Message
      • Notes
      • Operation
      • DTC Set Condition
      • Probable Causes
      • Diagnostic Procedure
    • DTC U0428: Steering Wheel Sensor CAN Message
      • Notes
      • Operation
      • DTC Set Condition
      • Probable Causes
      • Diagnostic Procedure
    • DTC U0431: ETACS CAN Message
      • Notes
      • Operation
      • DTC Set Condition
      • Probable Causes
      • Diagnostic Procedure
    • DTC U1073: Bus-Off
      • Notes
      • DTC Set Condition
      • Probable Causes
    • DTC U1195: Coding not Completed
      • Notes
      • Operation
      • DTC Set Condition
      • Probable Causes
      • Diagnostic Procedure
    • DTC U119A: Chassis No. Mismatch
      • Notes
      • Operation
      • DTC Set Condition
      • Probable Causes
      • Diagnostic Procedure
    • DTC U1425: T/M CAN Message
      • Notes
      • Operation
      • DTC Set Condition
      • Probable Causes
      • Diagnostic Procedure
    • DTC U1426: ASC CAN Message
      • Notes
      • Operation
      • DTC Set Condition
      • Probable Causes
      • Diagnostic Procedure
    • DTC U1427: Implausible Wheel Speed Data
      • Notes
      • Operation
      • DTC Set Condition
      • Probable Causes
      • Diagnostic Procedure
    • DTC U1428: Sensor Cluster CAN Message
      • Notes
      • Operation
      • DTC Set Conditions
      • Probable Causes
      • Diagnostic Procedure
    • DTC U142B: Invalid data received from EPS
      • Notes
      • Operation
      • DTC Set Condition
      • Probable Causes
      • Diagnostic Procedure
  • Symptom Procedures
    • INSPECTION PROCEDURE 1: Communication Between Scan Tool and AWC-ECU Cannot be Established
      • Comments On Trouble Symptom
      • Probable Causes
      • Diagnostic Procedure
    • INSPECTION PROCEDURE 2: Shifting the Drive Mode Selector Does not Change the Mode
      • Comments On Trouble Symptom
      • Probable Causes
      • Diagnostic Procedure
    • INSPECTION PROCEDURE 3: The Tight Corner Braking Phenomenon* Appears with the S-AWC Drive Mode-selector in the AWC ECO or NORMAL Position
      • Notes
      • Comments On Trouble Symptom
      • Probable Causes
      • Diagnosis
    • INSPECTION PROCEDURE 4: 4WD system check screen is displayed on the center of the multi-information display and a "4WD" symbol flashes at the left top. But no diagnostic trouble codes are stored
      • Comments On Trouble Symptom
      • Probable Causes
      • Diagnostic Procedure
    • INSPECTION PROCEDURE 5: Malfunction of Power Supply Circuit System
      • Comments On Trouble Symptom
      • Probable Causes
      • Diagnostic Procedure
    • INSPECTION PROCEDURE 6: When the ECO Mode Switch is Turned On, the Drive Mode is not Switched into AWC ECO Mode
      • Comments On Trouble Symptom
      • Probable Causes
      • Diagnostic Procedure
  • Data List Reference Table
  • Special Function
    • Reset
    • Test
  • Check At AWC-Ecu Terminal
• Special Tools
• On-Vehicle Service
  • A/T Control Component Layout
  • Essential Service
    • Transmission Fluid Check
    • Transmission Fluid Change
    • Flushing Coolers And Tubes
    • Oil Cooler Flow Check
    • Transmission Range Switch Check
    • Transmission Range Switch And Control Cable Adjustment
    • Transfer Oil Level Check
    • Transfer Oil Change
    • ELECTRONIC CONTROL COUPLING (FRONT) OPERATION CHECK <Vehicles WITH S-AWC>
    • ELECTRONIC CONTROL COUPLING (CENTER) OPERATION CHECK <Vehicles WITH S-AWC>
  • Automatic Transaxle Control Component Check
    • Transmission Range Switch Check
    • A/T Control Relay Check
    • Solenoid Valve Check
    • Transmission Fluid Temperature Sensor Check
    • ELECTRONIC CONTROL COUPLING SOLENOID (FRONT) CHECK <Vehicles WITH S-AWC>
    • ELECTRONIC CONTROL COUPLING SOLENOID (CENTER) CHECK <Vehicles WITH S-AWC>
    • Selector Lever Operation Check
    • Shift Lock Mechanism Check
      • System Check
      • Component Parts Check
        • Shift Lock Link
        • Shift Lock Solenoid
• Transaxle Control
  • Removal And Installation
  • Inspection
    • Switch Check
    • KEY LOCK RELAY CHECK <Vehicles WITHOUT KOS>
• Transaxle Assembly
  • Removal And Installation
    • Notes
    • Removal Service Points
      • <<A>> Transaxle Assembly Upper Part Coupling Bolt Removal
      • <<B>> Torque Converter And Drive Plate Coupling Bolt Removal
      • <<c>> ENGINE ASSEMBLY HOLDING
    • Installation Service Points
      • >>A<< Transaxle Assembly Installation
      • >>B<< Transaxle Control Cable (Transaxle Side) Installation
• Transfer Assembly
  • REMOVAL AND INSTALLATION
    • Notes
    • Removal Service Point
      • <<A>> Exhaust Manifold Bracket
  • REMOVAL AND INSTALLATION
    • Notes
    • Removal Service Point
      • <<A>> Transfer Assembly Removal
• Transaxle Control Module (TCM)
  • Removal And Installation
• AWC-ECU
  • Removal And Installation
• A/T Fluid Cooler Line
  • Removal And Installation
• Paddle Shift Assembly
  • Removal And Installation
  • Paddle Shift Switch Check