Section 67 (Wireless Control Module (WCM) - Lancer Evolution)
WARNING: This page is about a different variant/trim than selected.
- General Information
- Special Tools
- Diagnosis
- Standard Flow Of Diagnostic Troubleshooting
- Diagnostic Function
- Id Codes Registration Judgment Table
- Warnings/Alarms
- Diagnostic Trouble Code Chart
- Diagnostic Trouble Code Procedures
- DTC B1731: Engine control module communication timeout
- DTC B1761: VIN code not programmed
- DTC B1A08: Keyless/KOS key1 performance; DTC B1A09: Keyless/KOS key2 performance; DTC B1A0A: Keyless/KOS key3 performance; DTC B1A0B: Keyless/KOS key4 performance; DTC B1A0C: Keyless key 5 performance; DTC B1A0D: Keyless key 6 performance; DTC B1A0E: Keyless key 7 performance; DTC B1A0F: Keyless key 8 performance
- DTC B1A10: Keyless/KOS key 1 low battery; DTC B1A11: Keyless/KOS key 2 low battery; DTC B1A12: Keyless/KOS key 3 low battery; DTC B1A13: Keyless/KOS key 4 low battery; DTC B1A14: Keyless key 5 low battery; DTC B1A15: Keyless key 6 low battery; DTC B1A16: Keyless key 7 low battery; DTC B1A17: Keyless key 8 low battery
- DTC B1A24: Key ID not registered
- DTC B1A25: Key ID unmatched
- DTC B1A28: Engine control module authenticate error
- DTC B1A35: Transponder read error
- DTC B2101: IG SW start POS. circuit low; DTC B2102: IG SW start POS. circuit high
- DTC B2204: Coding data mismatch
- DTC B2206: VIN code mismatch
- DTC B2352: Antenna fail
- DTC B2401: Keyless/KOS key ID not register
- DTC B2415: RA module power voltage
- DTC B2416: ECU internal error
- DTC C1608: EEPROM Error
- DTC C1900: No Registration
- DTC C1901: Vehicle Speed Information Abnormality
- DTC C1910: Transmitter low battery voltage abnormality 1; DTC C1920: Transmitter low battery voltage abnormality 2; DTC C1930: Transmitter low battery voltage abnormality 3; DTC C1940: Transmitter low battery voltage abnormality 4; DTC C1911: Reception abnormality 1; DTC C1921: Reception abnormality 2; DTC C1931: Reception abnormality 3; DTC C1941: Reception abnormality 4
- DTC C1913: Acceleration sensor abnormality 1; DTC C1923: Acceleration sensor abnormality 2; DTC C1933: Acceleration sensor abnormality 3; DTC C1943: Acceleration sensor abnormality 4; DTC C1914: Pressure sensor abnormality 1; DTC C1924: Pressure sensor abnormality 2; DTC C1934: Pressure sensor abnormality 3; DTC C1944: Pressure sensor abnormality 4
- DTC C1912: Tire inflation pressure warning 1; DTC C1922: Tire inflation pressure warning 2; DTC C1932: Tire inflation pressure warning 3; DTC C1942: Tire inflation pressure warning 4
- DTC C1915: Transmitter OFF Mode 1; DTC C1925: Transmitter OFF Mode 2; DTC C1935: Transmitter OFF Mode 3; DTC C1945: Transmitter OFF Mode 4
- DTC U0019: Bus off (CAN-B)
- DTC U0141: ETACS-ECU CAN timeout
- DTC U0151: SRS-ECU CAN timeout
- DTC U0154: Occupant classification-ECU CAN timeout
- DTC U0155: Combination meter CAN timeout
- DTC U0164: A/C-ECU CAN timeout
- DTC U0184: Audio CAN timeout
- DTC U0195: Satellite radio tuner CAN timeout
- DTC U0197: Hands free module CAN timeout
- DTC U0245: Audio visual navigation unit CAN timeout
- DTC U1412: Implausible Vehicle Speed Signal Received
- DTC U1415: Coding not completed/Data fail
- DTC U1417: Implausible coding data
- Data List Reference Table
- Trouble Symptom Chart
- Symptom Procedures
- Inspection Procedure 1: Scan tool cannot communicate with WCM
- Inspection Procedure 2: The ignition key cannot be registered using scan tool
- Inspection Procedure 3: Engine does not start (cranking but no initial combustion)
- Inspection Procedure 4: Abnormality in WCM power supply and ground circuits
- Inspection Procedure 5: Keyless entry system does not work
- Inspection Procedure 6: Keyless entry hazard light answerback function, the dome light answerback function or the horn answerback function does not work normally
- Inspection Procedure 7: The timer lock function does not work after the doors have been unlocked by the keyless entry system
- Inspection Procedure 8: The trunk is not opened when the keyless entry transmitter "TRUNK" button is operated
- Inspection Procedure 9: Power door locks with selective unlocking does not work
- Check At Ecu Terminals
- On-Vehicle Service
- Id Codes Registration Procedure
- Registration Using Scan Tool MB991958 (M.U.T.-III Sub Assembly)
- Notes
- Supply Unit List For Individual Key
- Key Supply Unit List For Other Than Individual Key
- "Key Registration"/"Additional key registration" METHOD
- "Key Registration (Barcode No.)" METHOD
- "Keyless ID Reg." METHOD
- "Tire Pressure Sensor ID Registration" METHOD
- "TPMS transmitter check" METHOD
- "Tire Pressure Sensor ID Check" METHOD
- Registration Not Using Scan Tool MB991958 (M.U.T.-III Sub Assembly) <USA Only>
- Keyless Id Not Using Scan Tool MB991958 (M.U.T.-III Sub Assembly) <USA Only>
- Registration Using Scan Tool MB991958 (M.U.T.-III Sub Assembly)
- TPMS Transmitter Check
- TPMS Transmitter Id Check
- Keyless Entry System Check
- Inspection Of Keyless Entry Timer Lock Function
- Power Door Locks With Selective Unlocking Inspection
- Customization Function
- Id Codes Registration Procedure
- WCM
- Transmitter
- TPMS Transmitter