Rear Axle Hub: Installation

HINT

• Use the same procedures for the RH side and LH side.
• The procedures listed below are for the LH side.
• A bolt without a torque specification is shown in the standard bolt chart (SS-2).

1. INSTALL REAR AXLE HUB AND BEARING ASSEMBLY LH 
   1. Install the parking brake plate, cable support bracket and parking brake anchor block to the rear axle carrier with the 2 nuts

      Torque: 76 N*m (775 kgf*cm, 56 ft.*lbf) 

   2. Hold the axle hub and bearing in a vise between aluminum plates.
      NOTE: Do not overtighten the vise.
      Fig 1: Locating Parking Brake Anchor Block With Nuts

      Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
   3. Install the axle hub and bearing to the rear axle carrier with the 4 bolts.

      Torque: 97 N*m (989 kgf*cm, 72 ft.*lbf) 

      Fig 2: Locating Axle Hub Bolts

      Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
2. INSTALL REAR NO. 1 WHEEL BEARING DUST DEFLECTOR LH 
   1. Using SST and a hammer, install the bearing dust deflector to the rear axle carrier.

      SST 09950-70010 (09951-07150), 09951-01000 

      HINT:

      Align the hole for the speed sensor in the No. 1 bearing dust deflector with the rear axle carrier.

      Fig 3: Identifying Bearing Dust Deflector To Rear Axle Carrier

      Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
3. INSTALL REAR AXLE ASSEMBLY LH 
   1. Engage the spline part of the rear axle carrier to the spline part of the drive shaft.
   2. Using a jack, lift up the rear axle carrier, and align the installation positions of each arm.
      NOTE: Place a wooden block between the jack and rear axle carrier to prevent damage.
4. TEMPORARILY CONNECT PNEUMATIC CYLINDER WITH REAR SHOCK ABSORBER ASSEMBLY LH  (See INSTALLATION )
5. CONNECT REAR UPPER NO. 1 CONTROL ARM ASSEMBLY LH 
   1. Connect the control arm with a new nut to the axle carrier.

      Torque: 160 N*m (1632 kgf*cm, 118 ft.*lbf) 

      Fig 4: Identifying Rear Upper No. 1 Control Arm With Nut

      Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
6. CONNECT REAR UPPER NO. 2 CONTROL ARM ASSEMBLY LH 
   1. Connect the control arm with a new nut to the axle carrier

      Torque: 160 N*m (1632 kgf*cm, 118 ft.*lbf) 

      Fig 5: Identifying Rear Upper No. 2 Control Arm With Nut

      Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
7. CONNECT TOE CONTROL LINK SUB-ASSEMBLY LH 
   1. Connect the control link with a new nut to the axle carrier

      Torque: 118 N*m (1203 kgf*cm, 87 ft.*lbf) 

      Fig 6: Identifying Control Link With Nut To Axle Carrier

      Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
8. TEMPORARILY TIGHTEN REAR NO. 2 SUSPENSION ARM ASSEMBLY LH 
   1. Install the stud of the suspension arm, and temporarily install a washer, nut and the bolt to the axle carrier.
      Fig 7: Locating Rear No. 2 Suspension Arm Nut

      Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
   2. Temporarily install the No. 2 suspension arm with the No 2 suspension toe adjust plate, rear suspension attachment and nut to the suspension member
      Fig 8: Identifying No 2 Suspension Toe Adjust Plate

      Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
9. CONNECT REAR NO. 1 SUSPENSION ARM ASSEMBLY LH 
   1. Connect the suspension arm with a new nut to the axle carrier

      Torque: 118 N*m (1203 kgf*cm, 87 ft.*lbf) 

      Fig 9: Locating Suspension Arm With Nut To Axle Carrier

      Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
10. APPLY HIGH TEMPERATURE GREASE  (See REASSEMBLY )
11. INSTALL NO. 2 PARKING BRAKE SHOE ASSEMBLY LH  (See REASSEMBLY )
12. INSTALL NO. 1 PARKING BRAKE SHOE ASSEMBLY LH  (See REASSEMBLY )
13. INSTALL PARKING BRAKE SHOE ADJUSTING SCREW SET LH  (See REASSEMBLY )
14. INSTALL NO. 2 PARKING BRAKE SHOE RETURN TENSION SPRING  (See REASSEMBLY )
15. INSTALL PARKING BRAKE SHOE LEVER LH  (See REASSEMBLY )
16. INSTALL NO. 1 PARKING BRAKE SHOE RETURN TENSION SPRING  (See REASSEMBLY )
17. CHECK PARKING BRAKE INSTALLATION  (See REASSEMBLY )
18. INSTALL REAR AXLE SHAFT NUT LH 
    1. Clean the threaded parts on the drive shaft and axle hub nut using a non-residue solvent
       NOTE:

       • Be sure to perform this work for a new drive shaft.
       • Keep the threaded parts free of oil and foreign objects.
    2. Using a 32 mm socket wrench, install a new rear axle shaft nut.

       Torque: 290 N*m (2957 kgf*cm, 214 ft.*lbf) 

       NOTE: Do not stake the shaft nut.

       HINT:

       Stake the axle shaft nut after inspecting the axle hub bearing looseness and axle hub runout

19. INSPECT REAR AXLE HUB BEARING LOOSENESS  (See ON-VEHICLE INSPECTION  )
20. INSPECT REAR AXLE HUB RUNOUT  (See ON-VEHICLE INSPECTION  )
21. INSTALL REAR DISC  (See INSTALLATION )
22. ADJUST PARKING BRAKE SHOE CLEARANCE  (See ADJUSTMENT )
23. CONNECT REAR SPEED SENSOR LH  (See INSTALLATION )
24. CONNECT REAR DISC BRAKE CALIPER ASSEMBLY LH 
    1. Connect the rear disc brake caliper with 2 new bolts.

       Torque: 86 N*m (877 kgf*cm, 63 ft.*lbf) 

       NOTE:

       • Do not twist the brake flexible hose.
       • Make sure the screw parts are free from foreign matter and are not damaged.
       • Be careful not to overtighten the bolts, as the rear axle carrier is made of aluminum.
       Fig 10: Locating Rear Disc Brake Caliper With Bolts

       Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
25. STAKE REAR AXLE SHAFT LH NUT 
    1. Using a chisel and a hammer, stake the axle shaft nut
       Fig 11: Staking Axle Shaft Nut

       Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
26. INSTALL LOAD SENSING VALVE SENSOR BRACKET 
    1. Install the load sensing valve sensor bracket to the toe control link with the bolt

       Torque: 3.6 to 6.9 N*m (37 to 70 kgf*cm, 32 to 61 in.*lbf) 

       Fig 12: Locating Load Sensing Valve Sensor Bracket

       Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
27. STABILIZE SUSPENSION  (See REAR SUSPENSION MEMBER )
28. CONNECT PNEUMATIC CYLINDER WITH REAR SHOCK ABSORBER ASSEMBLY LH  (See INSTALLATION )
29. CONNECT REAR STABILIZER LINK ASSEMBLY LH 
    1. Insert the bolt from the front of the vehicle Then install the rear stabilizer link with the nut

       Torque: 26 N*m (265 kgf*cm, 19 ft.*lbf) 

       Fig 13: Locating Rear Stabilizer Link With Nut

       Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
30. TIGHTEN REAR NO. 2 SUSPENSION ARM ASSEMBLY LH 
    1. Tighten the nut on the rear suspension member side

       Torque: 150 N*m (1530 kgf*cm, 111 ft.*lbf) 

       Fig 14: Identifying No 2 Suspension Toe Adjust Plate

       Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
    2. Tighten the nut on the rear axle carrier side

       Torque: 225 N*m (2294 kgf*cm, 166 ft.*lbf) 

31. INSTALL REAR WHEEL 

    Torque: 140 N*m (1428 kgf*cm, 103 ft.*lbf) 

32. PERFORM PARKING BRAKE SHOE BEDDING 
    1. Perform parking brake shoe bedding (see PROBLEM SYMPTOMS TABLE )
33. CHECK SUSPENSION CONTROL SYSTEM 
    1. Check the suspension control system (see ADJUSTMENT )
       Fig 15: Locating Rear No. 2 Suspension Arm Nut

       Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
34. INSPECT AND ADJUST REAR WHEEL ALIGNMENT  (See INSTALLATION )
35. CHECK ABS SPEED SENSOR SIGNAL 
    1. Check the speed sensor signal (BC-47)
36. ADJUST HEADLIGHT ASSEMBLY 
    1. for LED headlight

       Adjust the headlight (see ADJUSTMENT )

    2. for HID headlight

       Adjust the headlight (see ADJUSTMENT ).

37. ADJUST OBJECT RECOGNITION CAMERA 
    1. Adjust the object recognition camera (see ADJUSTMENT )