(Electronic Power Steering (EPS) Module - Electrical Diagnostics)

• Diagnostic Code Index
• DTC Troubleshooting
  • C200B-02 Steering Shaft Torque Sensor -Circuit Voltage Below Threshold
    • Notes
    • When Monitored And Set Conditions
    • Diagnostic Test
  • C200B-1C Steering Shaft Torque Sensor -Circuit Voltage Out Of Range
    • Notes
    • When Monitored And Set Conditions
    • Diagnostic Test
  • C200B-62 Steering Shaft Torque Sensor -Single Compare Failure
    • Notes
    • When Monitored And Set Conditions
    • Diagnostic Test
  • C200C-1C Steering Shaft Torque Sensor-Circuit Voltage Out Of Range
    • Notes
    • When Monitored And Set Conditions
    • Diagnostic Test
  • C200D-1C Motor Rotation Angle Sensor-Circuit Voltage Out Of Range
    • Notes
    • When Monitored And Set Conditions
    • Diagnostic Test
  • C200D-64 Motor Rotation Angle Sensor-Signal Plausibility Failure
    • Notes
    • When Monitored And Set Conditions
    • Diagnostic Test
  • U0001-88 High Speed Can Communication Bus-Bus Off
    • Notes
    • When Monitored And Set Conditions
    • Diagnostic Test
  • U0100-00 Lost Communication With ECM/Pcm "A"
    • Notes
    • When Monitored And Set Conditions
    • Diagnostic Test
  • U0121-00 Lost Communication With Anti-Lock Brake System (Abs) Control Module
    • Notes
    • When Monitored And Set Conditions
    • Diagnostic Test
  • U0155-00 IPC (Instrument Panel Cluster)-Missing Message
    • Notes
    • When Monitored And Set Conditions
    • Diagnostic Test
  • U0338-00 Software Incompatibility With Remote Function Actuation
    • Notes
    • When Monitored And Set Conditions
    • Diagnostic Test
  • U0401-00 Invalid Data Received From ECM/Pcm
    • Notes
    • When Monitored And Set Conditions
    • Diagnostic Test
  • U0415-00 Invalid Data Received From Anti-Lock Brake System (Abs) Control Module
    • Notes
    • When Monitored And Set Conditions
    • Diagnostic Test
  • U0423-00 Invalid Data Received From Instrument Panel Cluster (IPC) Control Module
    • Notes
    • When Monitored And Set Conditions
    • Diagnostic Test
  • U0515-00 Invalid Data Received From Remote Function Actuation
    • Notes
    • When Monitored And Set Conditions
    • Diagnostic Test
  • U2011-19 Motor-Circuit Current Above Threshold
    • Notes
    • When Monitored And Set Conditions
    • Diagnostic Test
  • U2011-1C Motor-Circuit Voltage Out Of Range
    • Notes
    • When Monitored And Set Conditions
    • Diagnostic Test
  • U2011-61 Motor-Signal Calculation Failure
    • Notes
    • When Monitored And Set Conditions
    • Diagnostic Test
  • U2011-62 Motor-Single Compare Failure
    • Notes
    • When Monitored And Set Conditions
    • Diagnostic Test
  • U2011-64 Motor-Signal Plausibility Failure
    • Notes
    • When Monitored And Set Conditions
    • Diagnostic Test
  • U2011-72 Motor-Actuator Stuck Open
    • Notes
    • When Monitored And Set Conditions
    • Diagnostic Test
  • U2011-92 Motor-Performance Or Incorrect Operation
    • Notes
    • When Monitored And Set Conditions
    • Diagnostic Test
  • U2300-54 Central Configuration-Missing Calibration
    • Notes
    • When Monitored And Set Conditions
    • Diagnostic Test
  • U2300-55 Central Configuration-Not Configured
    • Notes
    • When Monitored And Set Conditions
    • Diagnostic Test
  • U2300-56 Central Configuration-Invalid/Incompatible Configuration
    • Notes
    • When Monitored And Set Conditions
    • Diagnostic Test
  • U3000-16 Control Module-Circuit Voltage Below Threshold
    • Notes
    • When Monitored And Set Conditions
    • Diagnostic Test
  • U3000-1C Battery Voltage-Circuit Voltage Above Threshold 2
    • Notes
    • When Monitored And Set Conditions
    • Diagnostic Test
  • U3000-28 Control Module-Signal Bias Level Out Of Range/Zero Adjustment Failure
    • Notes
    • When Monitored And Set Conditions
    • Diagnostic Test
  • U3000-41 Control Module-General Checksum Failure
    • Notes
    • When Monitored And Set Conditions
    • Diagnostic Test
  • U3000-46 Control Module-Calibration/Parameter Memory Failure
    • Notes
    • When Monitored And Set Conditions
    • Diagnostic Test
  • U3000-47 Control Module-Watchdog/Safety Failure
    • Notes
    • When Monitored And Set Conditions
    • Diagnostic Test
  • U3000-49 Control Module-Internal Electronic Failure
    • Notes
    • When Monitored And Set Conditions
    • Diagnostic Test
  • U3000-4B Control Module-Over Temperature
    • Notes
    • When Monitored And Set Conditions
    • Diagnostic Test
  • U3000-61 Control Module-Signal Calculation Failure
    • Notes
    • When Monitored And Set Conditions
    • Diagnostic Test
  • U3000-64 Control Module-DST Calculation Failure
    • Notes
    • When Monitored And Set Conditions
    • Diagnostic Test
  • U3000-73 Control Module-Actuator Stuck Closed
    • Notes
    • When Monitored And Set Conditions
    • Diagnostic Test
  • U3000-96 Control Module-Component Internal Failure
    • Notes
    • When Monitored And Set Conditions
    • Diagnostic Test
  • U3003-16 Battery Voltage Level-Circuit Voltage Below Threshold
    • Notes
    • When Monitored And Set Conditions
    • Diagnostic Test
  • U3003-17 Battery Voltage-Circuit Voltage Above Threshold 1
    • Notes
    • When Monitored And Set Conditions
    • Diagnostic Test