Gearshift Mechanism, Checking
Overview:
- 1. Selector mechanism function test, refer to GEARSHIFT MECHANISM, CHECKING
- 2. Checking the ignition key lock, refer to GEARSHIFT MECHANISM, CHECKING
- 3. Selector Lever Handle Locking Button, Checking, refer to GEARSHIFT MECHANISM, CHECKING
- The starter does not work when the selector lever is in "S", "D", "R" or in the "tiptronic gate".
- If selector lever position "N" is selected at speeds greater than 5 km/h, the shift lock solenoid must not engage and block the selector lever. The selector lever can be moved into a another gear.
- For speeds below 2 km/h (almost standstill) and shifting into selector lever position "N", the shift lock solenoid must only engage after approximately 1 second. The selector lever can be move out of "N" only when the brake pedal is pressed.
Selector lever in "P" and the ignition turned on:
-- Do not press the brake pedal.
- The selector lever is locked and cannot be moved out of "P" while locking button on selector lever handle is pressed. The Shift Lock Solenoid -N110- locks the selector lever.
-- Press the brake pedal and hold it down.
- The Shift Lock Solenoid -N110- unlocks the selector lever. It is possible to shift into a gear. Press the button in the selector lever handle and slowly move the selector lever from "P" and through "R, N, D, S". While doing this, make sure the Transmission Range Display -Y6- inside the instrument cluster matches the actual position of the selector lever.
The selector lever is in "N" and the ignition is turned on:
-- Do not press the brake pedal.
- After a short waiting period: The selector lever is locked and cannot be shifted out of the "N" position despite the locking button on the selector lever handle being pressed. The Shift Lock Solenoid -N110- locks the selector lever.
-- Press the brake pedal.
- The Shift Lock Solenoid -N110- unlocks the selector lever. It is possible to shift into "D".
Selector lever in "D" and the ignition is on:
-- Move the selector lever into the "tiptronic gate".
- The "D" in the Selector Lever Transmission Range Position Display Unit -Y26- must turn off and the "+" and "-" must turn on.
- The Transmission Range Display -Y6- inside the instrument cluster must change from "PRNDS" to "654321" when the selector lever is moved into the "tiptronic gate".
If the specified values are not obtained:
-- Perform the"Guided Fault Finding" with a Vehicle Diagnostic Tester.
-- Adjust the selector lever cable. Vehicles through 11.2005, refer to SELECTOR LEVER CABLE, ADJUSTING , vehicles from 11.2005, refer to SELECTOR LEVER CABLE, ADJUSTING .
-- Locking button on selector lever handle, checking, refer to GEARSHIFT MECHANISM, CHECKING .
-- Check ignition key removal lock.
-- To reach "ignition on", turn the key to right.
-- Press the brake pedal and hold it down.
- It must be possible to move the selector lever out of "P" without "getting stuck" when the locking button in the selector lever handle is pressed.
-- Turn off the ignition.
- It should not be possible to remove the ignition key when the selector lever is in any other position than "P".
-- Move the selector lever into "P".
-- Remove ignition key.
- It should be possible to remove the key only when the selector lever is in "P".
- It is not possible to move the selector lever out of "P" when both the locking button and the brake pedal are pressed.
If the ignition key lock does not function as described, follow the "Guided Fault Finding" with a Vehicle Diagnostic Tester.
Make sure locking button moves easily.
- It must be possible to press the locking button without using great force.
- After releasing, the locking button must come all the way back out by itself.
If the specified values are not obtained:
-- Check whether selector lever handle is installed correctly: Vehicles through 11.2005, refer to SELECTOR LEVER HANDLE , vehicles from 11.2005, refer to SELECTOR LEVER HANDLE .
-- Check whether selector rod or selector lever is bent.
Function Test:
- The ignition is switched on.
Locking button on selector lever handle must be pressed for the following shifts. If it is not pressed, the selector lever cannot be shifted into the specified position.
- Move the selector lever from "P" into "R" and press the brake pedal at the same time.
- "D" into "S"
- "N" into "R" ; stationary, press the brake pedal after waiting longer
- "R" into "P"
If the specified values are not obtained:
-- Check whether selector lever handle is installed correctly: Vehicles through 11.2005, refer to SELECTOR LEVER HANDLE , vehicles from 11.2005, refer to SELECTOR LEVER HANDLE .
-- Follow the "Guided Fault Finding" with a Vehicle Diagnostic Tester and check the Shift Lock Solenoid -N110-.
-- Adjust the selector lever cable. Vehicles through 11.2005, refer to SELECTOR LEVER CABLE, ADJUSTING , vehicles from 11.2005, refer to SELECTOR LEVER CABLE, ADJUSTING .