Front Stabilizer Bar: Installation

INSTALL FRONT STABILIZER BAR BUSH
1. Install the stabilizer bar bush to the stabilizer bar.
  HINT:
  - Install the bush onto the stabilizer so that the bush stopper of the stabilizer bar faces the outside of the vehicle.
  - Install the bush with its cutout facing the front of the vehicle.
    
    Fig 1: Installing Front Stabilizer Bar Bush
    Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
INSTALL FRONT STABILIZER BAR
1. Install the stabilizer onto the crossmember with the paint mark on the left side of the vehicle.
  
  Fig 2: Installing Front Stabilizer Bar
  Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
INSTALL FRONT STABILIZER BRACKET LH
1. Provisionally tighten bolt A.
2. Tighten the bolts to the specified torque, in the order of B then A.
  Torque: 47 N.m (479 kgf*cm, 35 ft.*lbf)
INSTALL FRONT STABILIZER BRACKET RH
HINT:

The installation procedure for the RH side is the same as that for the LH side.

Fig 3: Locating Front Stabilizer Bracket RH Bolts
Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
INSTALL POWER STEERING GEAR (See INSTALLATION )
INSTALL FRONT SUSPENSION CROSSMEMBER SUB-ASSEMBLY (See INSTALLATION )
INSTALL FRONT STABILIZER LINK ASSEMBLY LH
1. Install the stabilizer link with the 2 nuts.
  HINT:
  
  If the ball joint turns together with the nut, use a socket hexagon wrench 6 to hold the stud.
INSTALL FRONT STABILIZER LINK ASSEMBLY RH
HINT:

The installation procedure for the RH side is the same as that for the LH side.

Fig 4: Locating Stabilizer Link Nuts
Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
INSTALL FRONT LOWER SUSPENSION ARM LH (See INSTALLATION )
INSTALL FRONT LOWER SUSPENSION ARM RH
HINT:

The installation procedure for the RH side is the same as that for the LH side.
INSTALL TIE ROD END SUB-ASSEMBLY LH (See INSTALLATION )
INSTALL TIE ROD END SUB-ASSEMBLY RH
HINT:

The installation procedure for the RH side is the same as that for the LH side.
INSTALL STEERING COLUMN HOLE COVER SUB-ASSEMBLY (See INSTALLATION )
INSTALL STEERING SLIDING YOKE SUB-ASSEMBLY (See INSTALLATION )
INSTALL COLUMN HOLE COVER SILENCER SHEET (See INSTALLATION )
INSTALL FRONT WHEEL
Torque: 103 N.m (1,050 kgf*cm, 76 ft.*lbf)
POSITION WHEELS FACING STRAIGHT AHEAD
INSTALL OUTER COWL TOP PANEL
Hatchback: See INSTALLATION

Sedan: See INSTALLATION
INSTALL COWL TO REGISTER DUCT SUB-ASSEMBLY (for Hatchback) (See INSTALLATION )
INSTALL FRONT AIR SHUTTER SEAL (for Sedan) (See INSTALLATION )
INSTALL FRONT WIPER MOTOR AND LINK
Hatchback: See INSTALLATION

Sedan: See INSTALLATION
INSTALL COWL TOP VENTILATOR LOUVER LH (for Hatchback) (See INSTALLATION )
INSTALL COWL TOP VENTILATOR LOUVER SUB-ASSEMBLY
Hatchback: See INSTALLATION

Sedan: See INSTALLATION
INSTALL HOOD TO COWL TOP SEAL (for Hatchback) (See INSTALLATION )
INSTALL COWL SIDE VENTILATOR SUB-ASSEMBLY LH (for Sedan) (See INSTALLATION )
INSTALL COWL SIDE VENTILATOR SUB-ASSEMBLY RH (for Sedan) (See INSTALLATION )
INSTALL FRONT WIPER ARM AND BLADE ASSEMBLY LH
Hatchback: See INSTALLATION

Sedan: See INSTALLATION
INSTALL FRONT WIPER ARM AND BLADE ASSEMBLY RH
Hatchback: See INSTALLATION

Sedan: See INSTALLATION
INSTALL FRONT WIPER ARM HEAD CAP
Hatchback: (See INSTALLATION )

Sedan: (See INSTALLATION )
INSPECT HOOD
Hatchback: (See ADJUSTMENT )

Sedan: (See ADJUSTMENT )
ADJUST HOOD
Hatchback: See ADJUSTMENT

Sedan: See ADJUSTMENT
CONNECT CABLE TO NEGATIVE BATTERY TERMINAL
Torque: 5.4 N.m (55 kgf*cm, 48 in.*lbf)
INSPECT AND ADJUST FRONT WHEEL ALIGNMENT (See ADJUSTMENT )