LEMON Manuals: Even more car manuals for everyone
Home >> Suzuki >> 2013 >> Kizashi Base, Standard Trans >> Repair and Diagnosis >> External Pages >> Different variant/trim >> Section 1 (Continuously Variable Transaxle (CVT)) >> Diagnostic Information and Procedures >> DTC Table

DTC Table

WARNING: This page is about a different variant/trim than selected.
NOTE:
  • With the CAN communication OBD generic scan tool, DTC No. with delta () mark in the following table can not be read.
  • For details of D/C (driving cycle), refer to OBD SYSTEM DESCRIPTION .
DTC DETECTING CONDITION CHART

DTC DTC name DTC detecting condition DTC detection logic MIL
P0602 Control Module Programming Error TCM internal failure (data programming error). 1 D/C Off
P062F Internal Control Module EEPROM Error TCM internal failure (EEPROM error). 1 D/C Lights up
P0641 Sensor Reference Voltage "A" Circuit/Open Primary and secondary pressure sensor power supply circuit voltage is out of specified value for 5 sec. 1 D/C Lights up
P0703 Brake Switch "B" Circuit Brake light switch signal received from ECM is no change. 2 D/C Lights up
P0705 Transmission Range Sensor "A" Circuit (PRNDL Input) Two or more transmission range sensor signals are input simultaneously for 2 sec. 1 D/C Lights up
P0707 Transmission Range Sensor "A" Circuit Low Transmission range signal is not input for 10 sec. 2 D/C Lights up
P0711 Transmission Fluid Temperature Sensor "A" Circuit Range/Performance CVT fluid temperature variation is lower than specified value even if engine was running for specified time after engine start. 2 D/C Lights up
P0712 Transmission Fluid Temperature Sensor "A" Circuit Low CVT fluid temperature signal circuit voltage is lower than specified value for 5 sec. 1 D/C Lights up
P0713 Transmission Fluid Temperature Sensor "A" Circuit High CVT fluid temperature signal circuit voltage is higher than specified value for 5 sec. 1 D/C Lights up
P0716 Input/Turbine Speed Sensor "A" Circuit Range/Performance This DTC is detected if all the following conditions are met.
  • Difference between engine speed and primary pulley speed is higher than 1000 rpm for 5 sec. when lock-up ON.
  • Difference between measured value and estimated value of primary pulley speed is higher than 1000 rpm for 5 sec. when lock-up ON.
 2 D/C Lights up
P0717 Input/Turbine Speed Sensor "A" Circuit No Signal Primary pulley speed signal is no signal even if secondary pulley speed signal is input. 1 D/C Lights up
P0721 Output Speed Sensor Circuit Range/Performance This DTC is detected if all of the following conditions are met.
  • Difference between measured engine speed and the estimated secondary pulley speed is higher than 1000 rpm for 5 sec. when lock-up.
  • Difference between measured primary pulley speed and the estimated secondary pulley speed is higher than 1000 rpm for 5 sec. when lock-up ON.
 2 D/C Lights up
P0722 Output Speed Sensor Circuit No Signal This DTC is detected if any one of the following conditions is met.
  • The secondary pulley speed is lower than 150 rpm for 5 sec. in a row when the primary pulley speed is higher than 1000 rpm.
  • The secondary pulley speed is 0 rpm for specified times when the vehicle speed is higher than 10 km/h (6 mile/h).
 1 D/C Lights up
P0741 Torque Converter Clutch Circuit Performance or Stuck Off Difference between engine speed and primary pulley speed is more than 130 rpm for 30 sec. even if TCC solenoid valve is ON. 2 D/C Lights up
P0776 Pressure Control Solenoid "B" Performance/Stuck Off Secondary pressure value is 1.2 MPa (12.2 kgf/cm2 , 174 psi, 12 bar) or higher for 30 sec. or more. 2 D/C Lights up
P0777 Pressure Control Solenoid "B" Stuck On Secondary pressure value is equal to or lower than specified value. 2 D/C Lights up
P0826 Manual Mode Control Switch Circuit This DTC is detected if any one of the following conditions is met.
  • Manual mode switch ON signal continues to be input for longer than 5 sec. even after "P", "R" or "N" range signal input.
  • ON signal of manual shift-down switch or manual shift-up switch is input for longer than 5 sec. even while manual mode switch is OFF.
 1 D/C Off
P0842 Transmission Fluid Pressure Sensor/Switch "A" Circuit Low Primary pressure sensor signal circuit voltage is lower than specified value for 5 sec. 1 D/C Lights up
P0843 Transmission Fluid Pressure Sensor/Switch "A" Circuit High Primary pressure sensor signal circuit voltage is higher than 4.7 V for 5 sec. 1 D/C Lights up
P0847 Transmission Fluid Pressure Sensor/Switch "B" Circuit Low Secondary pressure sensor signal circuit voltage is lower than specified value for 5 sec. 1 D/C Lights up
P0848 Transmission Fluid Pressure Sensor/Switch "B" Circuit High Secondary pressure sensor signal circuit voltage is higher than 4.7 V for 5 sec. 1 D/C Lights up
P0871 Transmission Fluid Pressure Sensor/Switch "C" Circuit Range/Performance Measured line pressure is out of specified line pressure that calculate base on secondary pressure for 5 sec. 2 D/C Lights up
P0961 Pressure Control Solenoid "A" Control Circuit Range/Performance Gear ratio calculated from primary pulley speed and secondary pulley speed is higher than specified value. 2 D/C Lights up
P0962 Pressure Control Solenoid "A" Control Circuit Low Monitored circuit voltage of line pressure control solenoid valve is lower than limit value even if TCM outputs power to its control circuit. 1 D/C Lights up
P0963 Pressure Control Solenoid "A" Control Circuit High Monitored circuit current of line pressure control solenoid valve is lower than limit value for 5 sec. even if TCM outputs power to its control circuit. 1 D/C Lights up
P0966 Pressure Control Solenoid "B" Control Circuit Low Monitored circuit voltage of secondary pressure control solenoid valve is lower than limit value even if TCM outputs power to its control circuit. 1 D/C Lights up
P0967 Pressure Control Solenoid "B" Control Circuit High Monitored circuit current of secondary pressure control solenoid valve is lower than limit value for 5 sec. even if TCM outputs power to its control circuit. 1 D/C Lights up
P1706 Torque Request Communication Error from TCM ECM detects abnormality of CAN communication data which TCM transmits. 1 D/C Off
P1810 Lockup/Select Control Circuit Monitor signal of the lock-up/select switching solenoid valve is different from its command signal. 1 D/C Lights up
P1816 Stepper Motor Circuit Malfunction Monitor signal of stepper motor is different from its command signal. 1 D/C Lights up
P1818 Stepper Motor Performance Difference between measured primary pulley speed and estimated primary pulley speed is higher than 1000 rpm for 5 sec. 2 D/C Lights up
P1824 Learning Value Initialization Data Reading Error TCM cannot read learning value in ROM. 1 D/C Off
P1825 Learning Value Initialization Data Mismatched TCM and learning value in ROM are mismatched. 2 D/C Off
P1970 Sensor Ground Circuit Malfunction Ground circuit of following sensors is open circuit for specified times.
  • CVT fluid temperature sensor
  • Primary pressure sensor
  • Secondary pressure sensor
 1 D/C Lights up
P2763 Torque Converter Clutch Pressure Control Solenoid Control Circuit High Monitored circuit current of TCC (Torque Converter Clutch) solenoid valve is lower than limit value for 5 sec. even if TCM outputs power to its control circuit. 1 D/C Lights up
P2764 Torque Converter Clutch Pressure Control Solenoid Control Circuit Low Monitored circuit current of TCC (Torque Converter Clutch) solenoid valve is higher than limit value even if TCM outputs power to its control circuit. 1 D/C Lights up
U0073 Control Module Communication Bus Off Refer to CAN DTC (LOST COMMUNICATION AND COMMUNICATION BUS OFF) TABLE . 1 D/C Lights up
U0100 Lost Communication With ECM 1 D/C Lights up
U0121 Lost Communication With ABS 1 D/C Off
U0140 Lost Communication With BCM 1 D/C Off
scientia non olet · About LEMON Manuals