DTC B27A5: Front Internal Antenna Open

DTC detecting condition :

When open circuit occurs in the harness between keyless access control module and front interior antenna.

Trouble symptom :

The keyless access with push button start system does not operate. (When the access key is in the front area of the passenger room)

CAUTION:

For replacement procedure of keyless access control module, refer to the "REGISTRATION MANUAL FOR IMMOBILIZER" provided as a separate volume .
Before performing diagnosis, refer to "CAUTION" in "General Description" . Ref. to KEYLESS ACCESS WITH PUSH BUTTON START (DIAGNOSTICS)>GENERAL DESCRIPTION>CAUTION .

Wiring diagram :

Keyless access with push button start system Ref. to WIRING SYSTEM>KEYLESS ACCESS WITH PUSH BUTTON START SYSTEM>WIRING DIAGRAM .

Courtesy of SUBARU OF AMERICA, INC.

CHECK LAN SYSTEM .
Inspect LAN system. Ref. to LAN SYSTEM (DIAGNOSTICS)>BASIC DIAGNOSTIC PROCEDURE>PROCEDURE .

Is the check result OK?

Yes: Go to 2.

No: Perform the inspection according to the diagnosis for LAN system.
CHECK CONNECTOR .
1. Disconnect the connector from the keyless access control module.
2. Disconnect the connector from the front interior antenna.
3. Check the connector.
Is the check result OK?

Yes: Go to 3.

No: Repair or replace the connector.
CHECK POWER SUPPLY CIRCUIT .
Using a tester, measure the voltage between the keyless access control module connector and chassis ground.

Connector & terminal

(i91) No. 4 (+) - Chassis ground (-):

Is the voltage 9.5 - 16 V?

Yes: Go to 4.

No: Check the power supply circuit.
CHECK HARNESS (OPEN CIRCUIT) .
Using a tester, measure the resistance between the keyless access control module connector and front interior antenna connector, and between keyless access control module connector and chassis ground.

Connector & terminal

(i92) No. 25 - (C35) No. 1:

(i92) No. 12 - (C35) No. 3:

(i92) No. 17 - Chassis ground:

(i91) No. 20 - Chassis ground:

Is the resistance less than 1 Ω?

Yes: Go to 5.

No: Repair or replace the open circuit of harness.
CHECK HARNESS (GROUND SHORT CIRCUIT) .
Using a tester, measure the resistance between the keyless access control module connector and chassis ground.

Connector & terminal

(i92) No. 25 - Chassis ground:

(i92) No. 12 - Chassis ground:

Is the resistance 10 kΩ or more?

Yes: Go to 6.

No: Repair or replace the short circuit of the harness.
CHECK DTC .
1. Connect the disconnected connectors.
2. Turn the ignition switch to ON.
3. Using the Subaru Select Monitor, perform the clear memory of [Keyless Access with Push Button Start (Collation)]. Ref. to COMMON (DIAGNOSTICS)>CLEAR MEMORY .
4. Read the DTC of [Keyless Access with Push Button Start (Collation)] using the Subaru Select Monitor. Ref. to KEYLESS ACCESS WITH PUSH BUTTON START (DIAGNOSTICS)>DIAGNOSTIC TROUBLE CODE (DTC) .
Is DTC B27A5 displayed?

Yes: Go to 7.

No: Even if DTC is displayed, the circuit has returned to a normal condition at this time. Reproduce the failure, and then perform the diagnosis again.

NOTE: In this case, temporary poor contact of connector, temporary open or short circuit of harness may be the cause.
CHECK FRONT INTERIOR ANTENNA .
1. Turn the ignition switch to OFF.
2. Replace the front interior antenna with the rear interior antenna. Ref. to SECURITY AND LOCKS>KEYLESS ACCESS INDOOR ANTENNA>REMOVAL .
3. Turn the ignition switch to ON.
4. Using the Subaru Select Monitor, perform the clear memory of [Keyless Access with Push Button Start (Collation)]. Ref. to COMMON (DIAGNOSTICS)>CLEAR MEMORY .
5. Read the DTC of [Keyless Access with Push Button Start (Collation)] using the Subaru Select Monitor. Ref. to KEYLESS ACCESS WITH PUSH BUTTON START (DIAGNOSTICS)>DIAGNOSTIC TROUBLE CODE (DTC) .
Is DTC B27A5 displayed?

Yes: Replace the keyless access control module. Ref. to SECURITY AND LOCKS>KEYLESS ACCESS CM>REMOVAL .

No: Malfunction occurred in the front interior antenna.