LEMON Manuals: Even more car manuals for everyone
Home >> Subaru >> 2008 >> Outback Base, Automatic >> Repair and Diagnosis >> External Pages >> Different car >> Section 182 (LAN Communication System - LAN System (Diagnostics)) >> Subaru Select Monitor >> Operation >> Registration Body Integrated Unit (Equipment Setting)

Registration Body Integrated Unit (Equipment Setting)

WARNING: This page is about a different car, the 2008 Subaru Impreza. However, it is still accessible from the selected car via links, so may be relevant.
CAUTION: Body integrated unit is core of LAN system, and also can select the function of all vehicle system control. It is possible to control the original functions of vehicle when registrations of body integrated unit and function setting are corresponded to vehicle equipment.
If registrations and function setting are different from vehicle equipment, vehicle system does not operate normally and diagnosis cannot be performed correctly. Pay attention to following item.
  • Be sure to correspond registrations and function settings to vehicle equipment.
  • Do not change the settings of vehicle improperly.
  • Confirm key illumination does not blink or "Factory initial setting" of body integrated unit registrations is "Market". If "Factory initial setting" is set to "Factory", key illumination blinks when ignition key is turned ON, to notify that the settings are unconfirmed.
  • Key illumination does not blink with ignition switch turned to ON and go off with door closed.
  • Be sure to register immobilizer if body integrated unit is replaced with a new part, (models with immobilizer)
  • Make a registration of immobilizer when the parts related to immobilizer have been replaced. Refer to the "REGISTRATION MANUAL FOR IMMOBILIZER".
  1. Connect the SDI to data link connector located in the lower portion of the instrument panel (on the driver's side).
    Fig 1: Identifying Data Link Connector Location
    G05663967Courtesy of SUBARU OF AMERICA, INC.
    CAUTION: Do not connect the scan tools other than the Subaru Select Monitor.
  2. Start a PC.
  3. Turn the ignition switch to ON (engine OFF), and run the "PC application for Subaru Select Monitor".
  4. On the «Main Menu», select {Each System Check}.
  5. On the «System Selection Menu» display screen, select the {Integ. Unit mode}.
  6. Click the [OK] button after the control module name {Integrated unit} is displayed.
  7. On the «Integ. unit mode failure diag» display screen, select the {Unit customization}.
  8. Change the setting with UP/DOWN key.
    • List of body integrated unit registration item
    NOTE: Setting is different depending on the grade of vehicle.
    DATA INITIAL SETTING

    Data Initial setting Registration Remarks
    A/C ECM setting OFF ON Illumination control does not operate if A/C ECM setting is set to "OFF" in case of model with auto A/C.
    OFF If A/C ECM setting is set to "ON" in case of model without auto A/C, illumination change to night illumination and it is difficult to be recognized.
    P/W ECM setting OFF ON Set to "OFF" for all vehicles.
    OFF
    Center display setting (manufacturer option) OFF ON Set the center display failure to "OFF".
    OFF
    Wiper deicer setting (manufacturer option) OFF ON ON signal does not output with operation of wiper deicer switch if wiper deicer is set to "OFF" in models with a wiper deicer.
    OFF
    Factory initial setting (Reset of body integrated unit) Factory Factory (Reset) If Factory initial setting is set to "Factory", registrations of items above is changed to "OFF". Be sure to set to "Market".
    Market (Settlement)
    CAUTION:
    • To perform normal operation of vehicle and diagnosis, the above settings must match the actual vehicle equipment.
    • When body integrated unit is a new part or "Factory" mode, key illumination blinks to show equipment settings have not been completed. Check the detailed procedures of function setting.
    • Be sure not to change Factory initial setting except installation of new body integrated unit.
    NOTE: "Factory" mode:
    • Body integrated unit has not been set yet. It can be recognized by key illumination blinking with ignition switch turned to ON.
    • All replacement body integrated units are set to Factory mode. When replacing a body integrated unit, be sure to perform the registration operation.

      "Market" mode:

    • Each settings have been set. It can be recognized by key ring illumination coming on in concocting with room light and going off with ignition switch turned to ON.
  9. Perform the Factory setting. On the <<ECM customizing" display screen of Subaru Select Monitor, select the {Factory initial setting}.
  10. Change the mode from Factory to Market.
  11. Change the Subaru Select Monitor system selection to «Immobilizer» to register the immobilizer key. (Model with immobilizer)
  12. Perform the registration according to the procedures of the IMMOBILIZER REGISTRATION OPERATION MANUAL.
  13. When key registration is completed, "Do you want to register remote engine start?" is displayed. Perform registration only for equipped models.
  14. Perform the function setting (ECM customizing).

    <Ref. to FUNCTION SETTING (ECM CUSTOMIZING) , OPERATION, Subaru Select Monitor. >

NOTE: For details concerning the operation procedure, refer to the help file on PC application for Subaru Select Monitor.
scientia non olet · About LEMON Manuals