Manual Transaxle Overhaul - Evolution
- General Information
- Special Tools
- Transaxle
- Disassembly And Assembly
- Notes
- Disassembly Service Points
- Adjustment Before Assembly
- Assembly Service Points
- >> A << Input Shaft/Output Shaft/Center Differential Installation
- >> B << 5TH-Reverse Speed Shift Fork/5TH-Reverse Speed Shift Rail/3RD-4TH Speed Shift Fork/3RD-4TH Speed Shift Rail Installation
- >> C << Spring Pin Installation
- >> D << Spacer And Outer Race Installation
- >> E << Transaxle Case Installation
- >> F << Under Cover Installation
- >> G << Control Housing Installation
- >> H << Select Lever Installation
- Inspection
- Disassembly And Assembly
- Input Shaft
- Disassembly And Assembly
- Notes
- Disassembly Service Points
- Assembly Service Points
- >> A << Oil Seal Installation
- >> B << Ball Bearing Installation
- >> C << Snap Ring Installation
- >> D << Synchronizer Spring Installation
- >> E << 3RD-4TH Speed Synchronizer Hub Installation
- >> F << Synchronizer Sleeve Installation
- >> G << 4TH Speed Gear Sleeve Installation
- >> H << 5TH Speed Gear Installation
- >> I << Thrust Plate Installation
- >> J << Thrust Plate Stopper Installation
- >> K << Ball Bearing Installation
- >> L << Snap Ring Installation
- Inspection
- Disassembly And Assembly
- Output Shaft
- Disassembly And Assembly
- Notes
- Disassembly Service Points
- Assembly Service Points
- >> A << Oil Seal Installation
- >> B << Taper Roller Bearing Installation
- >> C << 1ST Speed Gear Sleeve Installation
- >> D << Synchronizer Spring Installation
- >> E << 1ST-2ND Speed Synchronizer Hub Installation
- >> F << Synchronizer Sleeve Installation
- >> G << 2ND Speed Gear Sleeve Installation
- >> H << 3RD Speed Gear Installation
- >> I << Snap Ring Installation
- >> J << 4TH Speed Gear Installation
- >> K << 5TH Speed Gear Sleeve Installation
- >> L << Synchronizer Spring Installation
- >> M << 5TH Speed-Reverse Synchronizer Hub Installation
- >> N << Synchronizer Sleeve Installation
- >> O << Reverse Gear Bearing Sleeve Installation
- >> P << Taper Roller Bearing Installation
- >> Q << Snap Ring Installation
- Inspection
- Output Shaft
- Needle Roller Bearing
- Synchronizer Ring < For 5TH Speed >
- Outer Synchronizer Ring/Inner Synchronizer Ring/Synchronizer Cone < For Reverse >
- Outer Synchronizer Ring/Inner Synchronizer Ring/Synchronizer Cone < For 1 St Speed And 2 ND Speed >
- Synchronizer Sleeve And Hub
- Synchronizer Spring
- Speed Gears
- Disassembly And Assembly
- Reverse Idler Gear
- Speedometer Gear
- Select Lever
- Disassembly And Assembly
- Control Housing
- Clutch Housing
- Transmission Case
- Center Differential
- Transfer
- Specifications
- Fastener Tightening Specifications
- General Specifications
- Service Specifications
- Sealants And Adhesives
- Lubricants
- Snap Rings, Spacers And Thrust Plate For Adjustment
- Spacer (For adjustment of input shaft end play)
- Snap ring (For adjustment of input shaft front bearing end play)
- Snap ring (For adjustment of input shaft rear bearing end play)
- Thrust plate (For adjustment of input shaft 5th speed gear end play)
- Spacer (For adjustment of output shaft preload)
- Snap ring (For adjustment of output shaft rear bearing end play)
- Snap ring (For adjustment of output shaft 3rd speed gear end play)
- Spacer (For adjustment of center differential case preload)
- Spacer (For adjustment of center differential case backlash)