Diagnostic procedure

DTC P2096 (L3) DIAGNOSTIC PROCEDURE

STEP	INSPECTION		ACTION
1	VERIFY FREEZE FRAME DATA AND DIAGNOSTIC MONITORING TEST RESULTS HAVE BEEN RECORDED Have FREEZE FRAME DATA and DIAGNOSTIC MONITORING TEST RESULTS (Fuel system related) been recorded?	Yes	Go to the next step.
1		No	Record the FREEZE FRAME DATA and DIAGNOSTIC MONITORING TEST RESULTS on the repair order, then V go to the next step.
2	VERIFY RELATED REPAIR INFORMATION AVAILABILITY Verify related Service Bulletins and/or on-line repair information availability. Is any related repair information available?	Yes	Perform repair or diagnosis according to the available repair information. If the vehicle is not repaired, go to the next step.
2		No	Go to the next step.
3	VERIFY RELATED PENDING CODE OR STORED DTC Turn the ignition switch off then to the ON position (Engine off). Verify the related PENDING CODE or stored DTCs. Is the DTC P2177 or P2187 also present?	Yes	Go to the applicable DTC inspection. (See DTC TABLE [L3] .)
3		No	Go to the next step.
4	IDENTIFY TRIGGER DTC FOR FREEZE FRAME DATA Is DTC P2096 on FREEZE FRAME DATA?	Yes	Go to the next step.
4		No	Go to FREEZE FRAME DATA DTC inspection. (See DTC TABLE [L3] .)
5	VERIFY CURRENT INPUT SIGNAL STATUS OF HO2S. Connect the M-MDS to the DLC-2. Start the engine and warm it up completely. Access O2S12 PID. Read O2S12 PID under the following accelerator pedal condition (in NEUTRAL). More than 0.45 V when accelerator pedal is suddenly depressed (rich condition). Less than 0.45 V just after release of accelerator pedal (lean condition) Is the PID normal?	Yes	Go to the next step.
5		No	Visually inspect for the exhaust gas leakage between the TWC and HO2S. If there is no leakage, replace the HO2S. (See AIR FUEL RATIO (A/F) SENSOR, HEATED OXYGEN SENSOR (HO2S) REMOVAL/INSTALLATION [L3] .) Then go to Step 17.
6	VERIFY CURRENT INPUT SIGNAL STATUS Connect the M-MDS to the DLC-2. Verify the following PIDs. (See PCM INSPECTION [L3] .) APP1 APP2 ECT MAF TP REL VSS Are the PIDs normal?	Yes	Go to the next step.
6		No	Inspect the malfunctioning part according to the inspection results. Then go to Step 17.
7	VERIFY CURRENT INPUT SIGNAL STATUS UNDER FREEZE FRAME DATA CONDITION Connect the M-MDS to the DLC-2. Verify the following PIDs under the FREEZE FRAME DATA condition. (See PCM INSPECTION [L3] .) APP1 APP2 ECT MAF TPREL VSS Are the PIDs normal?	Yes	Go to the next step.
7		No	Inspect the malfunctioning part according to the inspection results. Then go to Step 17.
8	INSPECT THE A/F SENSOR Inspect the A/F sensor. (See AIR FUEL RATIO (A/F) SENSOR INSPECTION [L3] .) Is the A/F sensor normal?	Yes	Go to the next step.
8		No	Visually inspect for the exhaust gas leakage between the exhaust manifold and A/F sensor. If there is no leakage, replace A/F sensor. (See AIR FUEL RATIO (A/F) SENSOR, HEATED OXYGEN SENSOR (HO2S) REMOVAL/INSTALLATION [L3] .) Then go to Step 17.
9	VERIFY CURRENT INPUT SIGNAL STATUS OF MAF SENSOR Connect the M-MDS to the DLC-2. Start the engine. Access the MAF PID. Verify that the MAF PID changes quickly according to engine speed. Is the PID normal?	Yes	Go to Step 11.
9		No	Go to the next step.
10	INSPECT INTAKE AIR SYSTEM FOR EXCESSIVE AIR SUCTION Visually inspect the hose in intake air system for looseness, cracks or damages. Is there any malfunction?	Yes	Repair or replace the malfunctioning part, then go to Step 17.
10		No	Replace the MAF/IAT sensor, then go to Step 17.
11	INSPECT FUEL LINE PRESSURE Perform the "FUEL LINE PRESSURE INSPECTION". (See FUEL LINE PRESSURE INSPECTION [L3] .) Is there any malfunction?	Yes	Go to the next step.
11		No	Go to Step 13.
12	INSPECT FUEL SYSTEM FOR FUEL LEAKAGE Visually inspect fuel leakage in the fuel system. Is there fuel leakage?	Yes	Repair or replace the malfunctioning part, then go to Step 17.
12		No	Replace the fuel pump unit, then go to Step 17. (See FUEL PUMP UNIT REMOVAL/INSTALLATION [L3] .)
13	INSPECT IGNITION COIL WIRING HARNESSES Inspect the ignition coil related wiring harness condition (intermittent open or short circuit) for all cylinders. Are wiring harness conditions normal?	Yes	Go to the next step.
13		No	Repair the wiring harnesses, then go to Step 17.
14	INSPECT IGNITION SYSTEM OPERATION Perform spark test. (See ENGINE CONTROL SYSTEM OPERATION INSPECTION [L3] .) Is strong blue spark visible at each cylinder?	Yes	Go to the next step.
14		No	Repair or replace the malfunctioning part according to spark test result. Then go to Step 17.
15	INSPECT ENGINE COMPRESSION Inspect the engine compression. (See COMPRESSION INSPECTION [L3] .) Is there any malfunction?	Yes	Overhaul the engine, then go to Step 17.
15		No	Go to the next step.
16	INSPECT FUEL INJECTOR OPERATION Perform the Fuel Injector Operation Inspection. (See ENGINE CONTROL SYSTEM OPERATION INSPECTION [L3] .) Does the fuel injector operate normally?	Yes	Go to the next step.
16		No	Repair or replace malfunctioning part according to inspection result, then go to the next step.
17	VERIFY TROUBLESHOOTING OF DTC P2096 COMPLETED Make sure to reconnect all disconnected connectors. Clear the DTC from the PCM memory using the M-MDS. After warming up the engine, maintain the idle status for 1 min or more. Is the PENDING CODE for this DTC present?	Yes	Replace the PCM, then go to the next step. (See PCM REMOVAL/INSTALLATION [L3] .)
17		No	Go to the next step.
18	VERIFY AFTER REPAIR PROCEDURE Perform the "AFTER REPAIR PROCEDURE". (See AFTER REPAIR PROCEDURE [L3] .) Is any DTC present?	Yes	Go to the applicable DTC inspection. (See DTC TABLE [L3] .)
18		No	Troubleshooting completed.