| B11D9: 16 |
Vehicle Battery: Circuit Voltage Below Threshold |
GO to Pinpoint Test A |
| B11D9: 17 |
Vehicle Battery: Circuit Voltage Above Threshold |
GO to Pinpoint Test A |
| U0140: 00 |
Lost Communication With Body Control Module: No Sub Type Information |
GO to Pinpoint Test B |
| U2002: 9E |
Switch: Stuck On |
GO to Pinpoint Test C |
| U2009: 9E |
Rotary Encoder: Stuck On |
GO to Pinpoint Test D |
| U3000: 04 |
Control Module: System Internal Failure |
GO to Pinpoint Test D |
| C00A1: 57 |
Driveline Control Module: Invalid / Incompatible Software Component |
GO to Pinpoint Test E |
| C00A1: F1 |
Driveline Control Module: <Manufacturer Defined> |
GO to Pinpoint Test E |
| C00A5: 01 |
Driveline Control Module Transfer Case Unit Control Circuit Driver: General Electrical Failure |
GO to Pinpoint Test E |
| C00A5: 08 |
Driveline Control Module Transfer Case Unit Control Circuit Driver: Bus Signal / Message Failure |
GO to Pinpoint Test E |
| C00A5: 19 |
Driveline Control Module Transfer Case Unit Control Circuit Drive: Circuit Current Above Threshold |
GO to Pinpoint Test E |
| C00A5: 1C |
Driveline Control Module Transfer Case Unit Control Circuit Driver: Circuit Voltage Out of Range |
GO to Pinpoint Test E |
| C00A5: 49 |
Driveline Control Module Transfer Case Unit Control Circuit Drive: Internal Electronic Failure |
GO to Pinpoint Test E |
| C00A5: 4B |
Driveline Control Module Transfer Case Unit Control Circuit Drive: Over Temperature |
GO to Pinpoint Test E |
| C00A5: 96 |
Driveline Control Module Transfer Case Unit Control Circuit Drive: Component Internal Failure |
GO to Pinpoint Test E |
| C00A6: 07 |
4WD/AWD Transfer Case Unit Actuator: Mechanical Failure |
GO to Pinpoint Test F |
| C00A6: 18 |
4WD/AWD Transfer Case Unit Actuator: Circuit Current Below Threshold |
GO to Pinpoint Test G |
| C00A6: 19 |
4WD/AWD Transfer Case Unit Actuator: Circuit Current Above Threshold |
GO to Pinpoint Test G |
| C00A6: 4B |
4WD/AWD Transfer Case Unit Actuator: Over Temperature |
GO to Pinpoint Test H |
| C00A6: 54 |
4WD/AWD Transfer Case Unit Actuator: Missing Calibration |
GO to Pinpoint Test I |
| C00A6: 66 |
4WD/AWD Transfer Case Unit Actuator: Signal Has Too Many Transitions/Events |
GO to Pinpoint Test J |
| C00A6: 71 |
4WD/AWD Transfer Case Unit Actuator: Actuator Stuck |
GO to Pinpoint Test G |
| C00A6: 74 |
4WD/AWD Transfer Case Unit Actuator: Actuator Slipping |
GO to Pinpoint Test G |
| C00A6: 99 |
4WD/AWD Transfer Case Unit Actuator: Exceeded Learning Limit |
GO to Pinpoint Test G |
| C00A7: 11 |
4WD/AWD Transfer Case Unit Actuator Position Sensor "A": Circuit Short To Ground |
GO to Pinpoint Test K |
| C00A7: 13 |
4WD/AWD Transfer Case Unit Actuator Position Sensor "A": Circuit Open |
GO to Pinpoint Test K |
| C00A7: 17 |
4WD/AWD Transfer Case Unit Actuator Position Sensor "A": Circuit Voltage Above Threshold |
GO to Pinpoint Test K |
| C00A8: 11 |
4WD/AWD Transfer Case Unit Actuator Position Sensor "B": Circuit Short To Ground |
GO to Pinpoint Test L |
| C00A8: 13 |
4WD/AWD Transfer Case Unit Actuator Position Sensor "B": Circuit Open |
GO to Pinpoint Test L |
| C00A8: 17 |
4WD/AWD Transfer Case Unit Actuator Position Sensor "B": Circuit Voltage Above Threshold |
GO to Pinpoint Test L |
| C0631: 14 |
Front Axle Disconnect Actuator: Circuit Short To Ground Or Open |
GO to Pinpoint Test M |
| C0631: 17 |
Front Axle Disconnect Actuator: Circuit Voltage Above Threshold |
GO to Pinpoint Test N |
| C0631: 7E |
Front Axle Disconnect Actuator: Actuator Stuck On |
GO to Pinpoint Test O |
| C0631: 7F |
Front Axle Disconnect Actuator: Actuator Stuck Off |
GO to Pinpoint Test P |
| C0632: 14 |
Front Axle Disconnect Control Circuit: Circuit Short To Ground Or Open |
GO to Pinpoint Test Q |
| C0632: 17 |
Front Axle Disconnect Control Circuit: Circuit Voltage Above Threshold |
GO to Pinpoint Test Q |
| C0632: 38 |
Front Axle Disconnect Control Circuit: Signal Frequency Incorrect |
GO to Pinpoint Test Q |
| C0632: 85 |
Front Axle Disconnect Control Circuit: Signal Above Allowable Range |
GO to Pinpoint Test Q |
| C0632: 86 |
Front Axle Disconnect Control Circuit: Signal Invalid |
GO to Pinpoint Test Q |
| C0632: 98 |
Front Axle Disconnect Control Circuit: Component or System Over Temperature |
GO to Pinpoint Test Q |
| C0632: A1 |
Front Axle Disconnect Control Circuit: System Voltage |
GO to Pinpoint Test Q |
| C0633: 14 |
Front Half Shaft Speed Sensor: Circuit Short To Ground Or Open |
GO to Pinpoint Test R |
| C0633: 17 |
Front Half Shaft Speed Sensor: Circuit Voltage Above Threshold |
GO to Pinpoint Test R |
| C0633: 86 |
Front Half Shaft Speed Sensor: Signal Invalid |
GO to Pinpoint Test R |
| C0633: A1 |
Front Half Shaft Speed Sensor: System Voltage |
GO to Pinpoint Test R |
| P0562: 00 |
System Voltage Low: No Sub Type Information |
GO to Pinpoint Test E |
| P0563: 00 |
System Voltage high: No Sub Type Information |
GO to Pinpoint Test E |
| P0603: 00 |
Internal Control Module Keep Alive Memory (KAM) Error: No Sub Type Information |
GO to Pinpoint Test E |
| P0604: 00 |
Internal Control Module Random Access Memory (RAM) Error: No Sub Type Information |
GO to Pinpoint Test E |
| P0605: 00 |
Internal Control Module Read Only Memory (ROM) Error: No Sub Type Information |
GO to Pinpoint Test E |
| P0607: 00 |
Control Module Performance: No Sub Type Information |
GO to Pinpoint Test E |
| P060A: 00 |
Internal Control Module Monitoring Processor Performance: No Sub Type Information |
GO to Pinpoint Test E |
| P060B: 00 |
Internal Control Module A/D Processing Performance: No Sub Type Information |
GO to Pinpoint Test E |
| P060C: 00 |
Internal Control Module Main Processor Performance: No Sub Type Information |
GO to Pinpoint Test E |
| P0630: 00 |
VIN Not Programmed or Incompatible - ECM/PCM: No Sub Type Information |
GO to Pinpoint Test S |
| P064F: 00 |
Unauthorized Software/Calibration Detected: No Sub Type Information |
GO to Pinpoint Test E |
| P068A: 00 |
ECM/PCM Power Relay De-Energized - Too Early: No Sub Type Information |
GO to Pinpoint Test E |
| P1001: 00 |
KOER Not Able to Complete, KOER Aborted: No Sub Type Information |
GO to Pinpoint Test T |
| P1397: 01 |
System Voltage Out Of Self-Test Range: General Electrical Failure |
GO to Pinpoint Test T |
| P1501: 00 |
Vehicle Speed Sensor Out Of Self Test Range: No Sub Type Information |
GO to Pinpoint Test T |
| P160A: 00 |
Control Module Vehicle Options Reconfiguration Error: No Sub Type Information |
GO to Pinpoint Test S |
| P166E: 00 |
Internal control module all wheel drive disconnect control performance: No Sub Type Information |
GO to Pinpoint Test U |
| P1674: 00 |
Control Module Software Corrupted: No Sub Type Information |
GO to Pinpoint Test E |
| P1705: 00 |
Transmission Range Circuit Not Indicating Park/Neutral During Self-Test: No Sub Type Information |
GO to Pinpoint Test T |
| U0100: 00 |
Lost Communication With ECM/PCM "A": No Sub Type Information |
GO to Pinpoint Test V |
| U0101: 00 |
Lost Communication with TCM: No Sub Type Information |
GO to Pinpoint Test V |
| U0121: 00 |
Lost Communication With Anti-Lock Brake System (ABS) Control Module "A": No Sub Type Information |
GO to Pinpoint Test V |
| U0126: 00 |
Lost Communication With Steering Angle Sensor Module: No Sub Type Information |
GO to Pinpoint Test V |
| U0137: 00 |
Lost Communication With Trailer Brake Control Module: No Sub Type Information |
GO to Pinpoint Test V |
| U0138: 00 |
Lost Communication with All Terrain Control Module: No Sub Type Information |
GO to Pinpoint Test V |
| U0140: 00 |
Lost Communication With Body Control Module: No Sub Type Information |
GO to Pinpoint Test V |
| U0146: 00 |
Lost Communication With Serial Data Gateway "A": No Sub Type Information |
GO to Pinpoint Test V |
| U0151: 00 |
Lost Communication With Restraints Control Module: No Sub Type Information |
GO to Pinpoint Test V |
| U0155: 00 |
Lost Communication With Instrument Panel Cluster (IPC) Control Module: No Sub Type Information |
GO to Pinpoint Test V |
| U0164: 00 |
Lost Communication With HVAC Control Module: No Sub Type Information |
GO to Pinpoint Test V |
| U0212: 00 |
Lost Communication With Steering Column Control Module: No Sub Type Information |
GO to Pinpoint Test V |
| U0402: 00 |
Invalid Data Received from TCM: No Sub Type Information |
GO to Pinpoint Test W |
| U0415: 00 |
Invalid Data Received from Anti-Lock Brake System (ABS) Control Module "A": No Sub Type Information |
GO to Pinpoint Test W |
| U0422: 00 |
Invalid Data Received From Body Control Module: No Sub Type Information |
GO to Pinpoint Test W |
| U0423: 00 |
Invalid Data Received from Instrument Panel Cluster Control Module: No Sub Type Information |
GO to Pinpoint Test W |
| U0428: 00 |
Invalid Data Received From Steering Angle Sensor Module: No Sub Type Information |
GO to Pinpoint Test W |
| U1012: 00 |
Invalid Internal Control Module Monitoring Data Received from Anti-Lock Brake System (ABS) Control Module: No Sub Type Information |
GO to Pinpoint Test W |
| U1014: 00 |
Invalid Internal Control Module Monitoring Data Received from Restraints Control Module: No Sub Type Information |
GO to Pinpoint Test W |
| U2100: 00 |
Initial Configuration Not Complete: No Sub Type Information |
GO to Pinpoint Test S |
| U2101: 00 |
Control Module Configuration Incompatible: No Sub Type Information |
GO to Pinpoint Test S |
| U2200: 00 |
Control Module Configuration Memory Corrupt: No Sub Type Information |
GO to Pinpoint Test S |