LEMON Manuals: Even more car manuals for everyone
Home >> Lexus >> 2009 >> LS 600hL >> Repair and Diagnosis >> External Pages >> Different car >> Section 6 (Exterior) >> Front Bumper >> Installation

Front Bumper: Installation

WARNING: This page is about a different car, the 2008 Lexus LS 600hL. However, it is still accessible from the selected car via links, so may be relevant.
  1. INSTALL FRONT BUMPER BAR REINFORCEMENT LH 
    1. Install the bumper bar reinforcement with the 2 screws
      2. Fig 1: Identifying Front Bumper Bar Reinforcement And Screws
      G05786611Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
  2. INSTALL FRONT BUMPER BAR REINFORCEMENT RH 

    HINT

    Use the same procedures described for the LH side.

  3. INSTALL FRONT BUMPER SIDE RETAINER LH 
    1. Attach the claw to install the retainer, and then install the screw
      2. Fig 2: Identifying Retainer And Screws
      G04946433Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
  4. INSTALL FRONT BUMPER SIDE RETAINER RH 

    HINT.

    Use the same procedures described for the LH side

  5. INSTALL RADIATOR SUPPORT OPENING COVER 
    1. Install the radiator support opening cover with the 2 clips
    Fig 3: Identifying Radiator Support And Clips
    G04946432Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
  6. INSTALL FRONT LOWER SUSPENSION CROSSMEMBER 
    1. Install the suspension crossmember with the 4 bolts and 3 clips

      Torque: 25 N*m (255 kgf*cm, 18 ft.*lbf) 

    Fig 4: Identifying Suspension Crossmember With Bolts
    G04946431Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
  7. INSTALL FRONT LOWER BUMPER ABSORBER 
    1. Install the absorber
    Fig 5: Identifying Front Lower Bumper Absorber
    G04946430Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
  8. INSTALL FRONT BUMPER REINFORCEMENT 
    1. Install the reinforcement with the 6 bolts

      Torque: 29 N*m (296 kgf*cm, 21 ft.*lbf) 

      Fig 6: Identifying Reinforcement And Bolts
      G05786606Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
    2. Connect the cooler thermistor connector
    3. Install the height control cleaner to the reinforcement.
    4. w/ Headlight Cleaner System.

      Attach the 4 headlight cleaner hose clamps.

  9. INSTALL FRONT BUMPER ENERGY ABSORBER 
    1. Install the energy absorber.
      2. Fig 7: Identifying Front Bumper Energy Absorber
      G04946428Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
  10. INSTALL FRONT BUMPER COVER 
    1. Connect the 2 fog light connectors and No. 4 engine room main wire connector and install the front bumper.
    2. Attach the 6 claws to the connect the front bumper, as shown in the illustration

      HINT.

      Use the same procedures for the RH side and LH side

      Fig 8: Identifying Front Bumper Claws
      G05786627Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
    3. Install the bumper seal bracket and attach the clip.

      HINT

      Use the same procedures for the RH side and LH side

      Fig 9: Identifying Bumper Seal Bracket With Clip
      G05786603Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
    4. Install the 8 screws.
    Fig 10: Identifying Front Bumper And Screws
    G05786629Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
  11. INSTALL FRONT FENDER LINER LH 
    1. Install the 2 clips so that their grooves are vertical
      2. Fig 11: Identifying Front Fender Liner And Clips
      G04950730Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
  12. INSTALL FRONT FENDER LINER RH 

    HINT

    Use the same procedures described for the LH side

  13. INSTALL FRONT WHEEL OPENING EXTENSION PAD LH 
    1. Install the extension pad with the 5 screws and clip.
      2. Fig 12: Identifying Extension Pad, Clip And Screws
      G05786600Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
  14. INSTALL FRONT WHEEL OPENING EXTENSION PAD RH 

    HINT.

    Use the same procedures described for the LH side.

  15. INSTALL FRONT FENDER WHEEL OPENING MOULDING LH  (See INSTALLATION  )
  16. INSTALL FRONT FENDER WHEEL OPENING MOULDING RH 

    HINT.

    Use the same procedures described for the LH side.

  17. INSTALL RADIATOR GRILLE ASSEMBLY  (See INSTALLATION  )
  18. INSTALL COOL AIR INTAKE DUCT SEAL  (See INSTALLATION )
  19. INSTALL INLET AIR CLEANER COVER SUB-ASSEMBLY  (See INSTALLATION )
  20. INSTALL ENGINE ROOM SIDE COVER LH  (See INSTALLATION )
  21. INSTALL ENGINE ROOM SIDE COVER RH  (See INSTALLATION )
  22. CONNECT CABLE TO NEGATIVE BATTERY TERMINAL 
    NOTE: When disconnecting the cable, some systems need to be initialized after the cable is reconnected (see INITIALIZATION ).
  23. INSTALL BATTERY SERVICE HOLE COVER LH  (See INSTALLATION )
  24. INSTALL LUGGAGE COMPARTMENT MAT SUB-ASSEMBLY  (See INSTALLATION )
scientia non olet · About LEMON Manuals