LEMON Manuals: Even more car manuals for everyone
Home >> Infiniti >> 2007 >> FX45 >> Repair and Diagnosis >> Transmission >> Automatic Transmission >> On-Vehicle Service >> Parking Components (2WD Models Only) >> Installation

Parking Components (2WD Models Only): Installation

CAUTION: After completing installation, check A/T position, A/T fluid leakage and A/F fluid level. Refer to "CHECKING OF A/T POSITION ", "CHECKING A/T FLUID ".
  1. As shown in the figure, use a drift to drive rear oil seal into the rear extension until it is flush.
    CAUTION:
    • Do not reuse rear oil seal.
    • Apply ATF to rear oil seal.
      • Fig 1: Driving Rear Oil Seal Into Rear Extension
      G04875969Courtesy of NISSAN MOTOR CO., U.S.A.
  2. Install return spring to parking pawl.
    Fig 2: Identifying Return Spring To Parking Pawl
    G05218198Courtesy of NISSAN MOTOR CO., U.S.A.
  3. Install parking pawl (with return spring) and pawl shaft to rear extension.
    Fig 3: Installing Parking Pawl And Pawl Shaft
    G04875964Courtesy of NISSAN MOTOR CO., U.S.A.
  4. Install parking actuator support to rear extension.
    Fig 4: Installing Parking Actuator Support
    G04875963Courtesy of NISSAN MOTOR CO., U.S.A.
  5. Install needle bearing to rear extension.
    CAUTION:
  6. Install seal rings in output shaft.
    CAUTION:
    • Do not reuse seal rings.
    • Apply petroleum jelly to seal rings.
      • Fig 6: Identifying Seal Rings On Output Shaft
      G04875961Courtesy of NISSAN MOTOR CO., U.S.A.
  7. Install parking gear to output shaft
    Fig 7: Installing Parking Gear And Output Shaft
    G04875960Courtesy of NISSAN MOTOR CO., U.S.A.
  8. Install output shaft to transmission case.
    Fig 8: Installing Output Shaft From Transmission Case
    G04875959Courtesy of NISSAN MOTOR CO., U.S.A.
  9. Install bearing race to output shaft.
    Fig 9: Installing Bearing Race In Output Shaft
    G04875958Courtesy of NISSAN MOTOR CO., U.S.A.
  10. Apply recommended sealant (Genuine Anaerobic Liquid Gasket or equivalent. Refer to "RECOMMENDED CHEMICAL PRODUCTS AND SEALANTS ".) to rear extension assembly as shown in the figure.
    CAUTION: Completely remove all moisture, oil and old sealant, etc. from the transmission case and rear extension assembly mounting surfaces.
    Fig 10: Applying Recommended Sealant To Rear Extension Assembly
    G04875978Courtesy of NISSAN MOTOR CO., U.S.A.
  11. Install rear extension assembly to transmission case. (With needle bearing.)
    CAUTION: Insert the tip of parking rod between the parking pawl and the parking actuator support when assembling the rear extension assembly.
    Fig 11: Removal/Installation Of Rear Extension Assembly
    G04875957Courtesy of NISSAN MOTOR CO., U.S.A.
  12. Tighten rear extension assembly mounting bolts to specified torque. Refer to "COMPONENTS ".
    CAUTION: Do not reuse self-sealing bolts.
    Fig 12: Locating Bolts For Rear Extension Assembly And Transmission Case
    G04875955Courtesy of NISSAN MOTOR CO., U.S.A.
  13. Install engine mounting insulator (rear). Refer to "REMOVAL AND INSTALLATION (2WD MODELS) ".
  14. Install rear engine mounting member. Refer to "REMOVAL AND INSTALLATION (2WD MODELS) ".
  15. Install control rod. Refer to "CONTROL ROD REMOVAL AND INSTALLATION ".
  16. Install rear propeller shaft. Refer to "REMOVAL AND INSTALLATION ".
  17. Install exhaust front tube and center muffler. Refer to "COMPONENTS ".
  18. Install drain plug in oil pan, and then tighten drain plug to the specified torque. Refer to "COMPONENTS ".
    CAUTION: Do not reuse drain plug gasket.
  19. Pour ATF into A/T assembly. Refer to "CHANGING A/T FLUID ".
scientia non olet · About LEMON Manuals