Specifications Index
SPECIFICATIONS INDEX
| System | Specification/Procedure | |||
|---|---|---|---|---|
| Air Conditioning | ||||
| Service | ||||
| R1234yf | WORKING WITH A/C SERVICE STATION (1 OF 2) WORKING WITH A/C SERVICE STATION (2 OF 2) |
|||
| Torque | OVERVIEW - A/C COMPRESSOR | |||
| Axle Nut/Hub Nut/Wheel Bearing Unit | ||||
| Front | 200 Nm +90° | |||
| Rear | 200 Nm +90° (TORSION BEAM AXLE AND MULTI-LINK SUSPENSION) | |||
| Battery | BATTERY | |||
| Brakes | ||||
| Bleeding Sequence | HYDRAULIC SYSTEM, STANDARD BLEEDING | |||
| Disc Brakes | ||||
| Front | FRONT BRAKES | |||
| Rear | REAR BRAKES | |||
| Torque | ||||
| Front | OVERVIEW - FRONT BRAKES | |||
| Rear | OVERVIEW - REAR BRAKES | |||
| Charging | ||||
| Generator | GENERATOR | |||
| Torque | OVERVIEW - GENERATOR | |||
| Drive Belts | ||||
| Adjustment | ||||
| 1.5L | RIBBED BELT, REMOVING AND INSTALLING | |||
| 2.0L | RIBBED BELT, REMOVING AND INSTALLING | |||
| Belt Routing | ||||
| 1.5L | OVERVIEW - RIBBED BELT DRIVE | |||
| 2.0L | OVERVIEW - CYLINDER BLOCK, BELT PULLEY SIDE | |||
| Engine Cooling | ||||
| General Service Specifications | Refer to the appropriate FLUID CAPACITY TABLES information. | |||
| Radiator Cap Pressure | ||||
| 1.5L | Blue Cap The pressure release valve must open at 1.4 bar (20.31 psi). | |||
| 2.0L | Black Cap The pressure release valve must open at 1.6 to 1.8 bar (23.21 to 26.11 psi). | |||
| Thermostat R & I | N/A | |||
| Water Pump R & I | ||||
| 1.5L | COOLANT PUMP/COOLANT THERMOSTAT | |||
| 2.0L | COOLANT PUMP/COOLANT THERMOSTAT | |||
| Engine Mechanical | ||||
| 1.5L | ||||
| Compression | COMPRESSION, CHECKING | |||
| Oil Pressure | Checking the sensor and the oil pressure takes place using the Vehicle Diagnostic Tester | |||
| Overhaul | ENGINE ASSEMBLY (1.5) | |||
| 2.0L | ||||
| Compression | COMPRESSION, CHECKING | |||
| Oil Pressure | OIL PRESSURE, CHECKING | |||
| Idle | 0.85 to 1.6 bar (12.33 to 23.21 psi) | |||
| 2, 000 RPM | 1.2 to 1.6 bar (17.4 to 23.21 psi) | |||
| 3, 700 RPM | 1.2 to 1.6 bar (17.4 to 23.21 psi) | |||
| Overhaul | ENGINE ASSEMBLY (2.0L) | |||
| Fluid Specifications | See FLUIDS under MAINTENANCE tab. | |||
| Engine Oil Drain Plug | 30Nm | |||
| Flywheel/Flex Plate Torque | 60 Nm + 90° | |||
| Fuel System | ||||
| Fuel Pressure & Test Procedure | TRANSFER FUEL PUMP -G6-, CHECKING | |||
| Ignition | ||||
| Firing Order & Cylinder Identification | FIRING ORDER & CYLINDER IDENTIFICATION | |||
| Spark Plug | SPARK PLUGS, REPLACING | |||
| Starting | ||||
| Starter | STARTER | |||
| Torque | OVERVIEW - STARTER | |||
| Wheel Alignment | ||||
| Adjustment Specifications | AXLE ALIGNMENT SPECIFIED VALUES | |||
| Wheel & Tire | ||||
| Wheel Lug Nut Torque | 140 Nm | |||