Test Procedure

Step	Procedure	Result / Action to Take
1	PERFORM: Preliminary Check to verify the customers complaint. Refer to: PRELIMINARY CHECK . -- Was Complaint verified?	-- YES: GO TO: Step 2 Oxygen Sensor 1 After Catalytic Converter - GX7-, CHECKING (2) . -- NO: GATHER more information from customer about the complaint.
2	IGNITION: OFF. DISCONNECT: Oxygen Sensor 1 After Catalytic Converter - GX7- harness connector. CHECK: Oxygen Sensor 1 After Catalytic Converter - GX7- component connector terminal 1 to 2 for resistance. SPECIFIED VALUE: 1 - 5 Ω (@ 25° C). -- Was Value obtained?	-- YES: GO TO: Step 3 Oxygen Sensor 1 After Catalytic Converter - GX7-, CHECKING (3) . -- NO: REPLACE: Oxygen Sensor 1 After Catalytic Converter - GX7-. GO TO: Step 6 Oxygen Sensor 1 After Catalytic Converter - GX7-, CHECKING (6) .
3	IGNITION: ON. CHECK: Oxygen Sensor 1 After Catalytic Converter - GX7- harness connector terminal 1 to ground for voltage. IGNITION: OFF. SPECIFIED VALUE: Battery voltage. -- Were Values obtained?	-- YES: GO TO: Step 4 Oxygen Sensor 1 After Catalytic Converter - GX7-, CHECKING (4) . -- NO: PERFORM: Visual Inspection of wiring and component. CHECK: Wiring for open, high resistance, short or harness connector for damage, corrosion, loose or broken terminals. REPAIR: Faulty wiring or connector. GO TO: Step 6 Oxygen Sensor 1 After Catalytic Converter - GX7-, CHECKING (6) .
4	RECONNECT: Oxygen Sensor 1 After Catalytic Converter - GX7- harness connector. CONNECT: Scan Tool. START: Engine and let Idle. Perform the function test located in diagnostic mode 06. Refer to appropriate Diagnostic Mode 06 - Read Test Results for Specific Diagnostic Functions, DIAGNOSTIC MODES 01 - 09 . SPECIFIED VALUE: Mode 6 Pass. IGNITION: OFF. -- Were Values obtained?	-- YES: FAULT: Is intermittent. PERFORM: Visual Inspection of wiring and component. CHECK: Wiring for open, high resistance, short or harness connector for damage, corrosion, loose or broken terminals. REPAIR: Faulty wiring or connector. GO TO: Step 6 Oxygen Sensor 1 After Catalytic Converter - GX7-, CHECKING (6) . -- NO: GO TO: Step 5 Oxygen Sensor 1 After Catalytic Converter - GX7-, CHECKING (5) .
5	REMOVE: Engine Control Module -J623-. CHECK: Oxygen Sensor 1 After Catalytic Converter - GX7- harness connector terminal 2 to the Engine Control Module -J623- harness connector T91 / 11 for resistance. CHECK: Oxygen Sensor 1 After Catalytic Converter - GX7- harness connector terminal 3 to the Engine Control Module -J623- harness connector T91 / 26 for resistance. CHECK: Oxygen Sensor 1 After Catalytic Converter - GX7- harness connector terminal 4 to the Engine Control Module -J623- harness connector T91 / 25 for resistance. SPECIFIED VALUE: 0.5 Ω (± 0.3 Ω). -- Were Values obtained?	-- YES: REPLACE: Oxygen Sensor 1 After Catalytic Converter - GX7-. GO TO: Step 6 Oxygen Sensor 1 After Catalytic Converter - GX7-, CHECKING (6) . -- NO: PERFORM: Visual Inspection of wiring and component. CHECK: Wiring for open, high resistance, short or harness connector for damage, corrosion, loose or broken terminals. REPAIR: Faulty wiring or connector. GO TO: Step 6 Oxygen Sensor 1 After Catalytic Converter - GX7-, CHECKING (6) .
6	Final Procedure Perform a road test to verify repair. -- Does the original DTC return?	-- YES: CHECK: Engine Control Module -J623- harness connector for any damaged, pushed out pins. REPAIR: As necessary. If all electrical connections are OK: REPLACE: Engine Control Module -J623-. Clear the DTC's. Refer to DIAGNOSTIC MODE 04 - ERASE DTC MEMORY . Repair is complete. Generate Readiness Code. Refer to READINESS CODE . Return vehicle to Customer. -- NO: Perform the diagnostic procedure for any DTC's. If no DTC's return the repair is complete. Return vehicle to customer.