Specifications Index
SPECIFICATIONS INDEX
| System | Specification/Procedure | ||
|---|---|---|---|
| Air Conditioning | |||
| Service | CAPACITIES | ||
| Torque | FASTENER TIGHTENING SPECIFICATIONS | ||
| Axle Nut/Hub Nut | |||
| Front | 70 Nm + 90° turn | ||
| Rear | 180 Nm + 180° turn | ||
| Battery | GENERAL INFORMATION | ||
| Brakes | |||
| Bleeding Sequence | BRAKE SYSTEM, BLEEDING | ||
| Disc Brakes | FRONT BRAKES | ||
| Torque | FRONT BRAKES ASSEMBLY OVERVIEW, FN3 FRONT BRAKES OVERVIEW, FNR-G REAR BRAKES ASSEMBLY OVERVIEW, C 38 REAR BRAKES ASSEMBLY OVERVIEW, BOSCH REAR BRAKES OVERVIEW, CII 41 |
||
| Charging | |||
| Generator | DESCRIPTION AND OPERATION N/A | ||
| Torque | |||
| Drive Belts | |||
| Adjustment | |||
| 2.0L | RIBBED BELT (WITH TENSIONING ROLLER) | ||
| 2.5L | RIBBED BELT | ||
| Belt Routing | |||
| 2.0L | See the figure under RIBBED BELT (WITH TENSIONER) | ||
| 2.5L | See the figure under RIBBED BELT OVERVIEW | ||
| Engine Cooling | |||
| General Service Specifications | Refer to the appropriate MAINTENANCE, DIAGNOSIS - FLUID CAPACITY TABLES information. | ||
| Radiator Cap Pressure | |||
| 2.0L | 1.4 Bar | ||
| 2.5L | 1.4-1.6 Bar | ||
| Thermostat R & I | |||
| 2.0L | COOLANT THERMOSTAT | ||
| 2.5L | COOLANT THERMOSTAT | ||
| Water Pump R & I | |||
| 2.0L | COOLANT PUMP | ||
| 2.5L | COOLANT PUMP | ||
| Engine Mechanical | |||
| 2.0L | |||
| Compression | COMPRESSION TEST | ||
| Oil Pressure | Increase the engine speed further. At 2000 RPM and with the oil temperature at 80°C (176°F), the oil pressure must be a minimum 2.0 bar. At higher engine speeds, the oil pressure must not exceed 7.0 bar. If necessary, replace the oil filter bracket. |
||
| Overhaul | 10 ENGINE ASSEMBLY | ||
| Torque | FASTENER TIGHTENING SPECIFICATIONS | ||
| 2.5L | |||
| Compression | COMPRESSION PRESSURE, CHECKING | ||
| Oil Pressure | -- Start the engine and increase the engine speed: The LED must illuminate at 1.2 to 1.6 bar. Replace the oil pressure switch if it does not. -- Increase the engine speed further. At 2000 RPM and an oil temperature of 80°C (176°F), the oil pressure must be between 2.7 and 4.5 bar. At higher engine speeds the oil pressure must not exceed 7.0 bar |
||
| Overhaul | 10 ENGINE ASSEMBLY | ||
| Torque | FASTENER TIGHTENING SPECIFICATIONS | ||
| Fluid Specifications | See FLUIDS under MAINTENANCE tab. | ||
| Flywheel/Flex Plate Torque | 60 Nm + an additional 90° (1/4) turn. | ||
| Fuel System | |||
| Pressure Specification | |||
| 2.0L | at least 3.5 bar | ||
| 2.5L | The fuel pressure in the high pressure pipe can be up to 120 bar | ||
| Fuel Pressure Test Procedure | |||
| 2.0L | FUEL PRESSURE REGULATOR VALVE, CHECKING | ||
| 2.5L | FUEL PUMP PRESSURE, CHECKING | ||
| Ignition | |||
| Firing Order & Cylinder Identification | |||
| FIRING ORDER & CYLINDER IDENTIFICATION | |||
| Ignition Wires (Resistance) | Coil-On-Plug | ||
| Ignition Wires (Routing) | Coil-On-Plug | ||
| Spark Plug | |||
| 2.0L | Glow Plugs | ||
| 2.5L | TEST DATA AND SPARK PLUGS | ||
| Starting | |||
| Starter | STARTER, CHECKING | ||
| Torque | FASTENER TIGHTENING SPECIFICATIONS | ||
| Wheel Alignment | |||
| Adjustment Specifications | WHEEL ALIGNMENT SPECIFIED VALUES | ||
| Torque | N/A | ||
| Wheel & Tire | |||
| Wheel Lug Nut Torque | 120 Nm | ||