LEMON Manuals: Even more car manuals for everyone
Home >> Toyota >> 2012 >> Sienna Limited, AWD >> Repair and Diagnosis >> Steering >> Power Steering >> Power Steering System [Diagnostics - Introduction] >> Power Steering System >> Data List / Active Test >> Data List / Active Test

Data List / Active Test

  1. DATA LIST 

    HINT: 

    Using the Techstream to read the Data List allows the values or states of switches, sensors, actuators and other items to be read without removing any parts. This non-intrusive inspection can be very useful because intermittent conditions or signals may be discovered before parts or wiring is disturbed. Reading the Data List information early in troubleshooting is one way to save diagnostic time.

    NOTE:

    In the table below, the values listed under "Normal Condition" are reference values. Do not depend solely on these reference values when deciding whether a part is faulty or not.

    1. Turn the ignition switch off.
    2. Connect the Techstream to the DLC3.
    3. Turn the ignition switch to ON.
    4. Turn the Techstream on.
    5. Enter the following menus: Chassis / EMPS / Data List.
    6. According to the display on the Techstream, read the Data List.
    EMPS

    Tester Display Measurement Item/Range Normal Condition Diagnostic Note
    Meter Vehicle Velocity Vehicle speed from meter:
    Minimum: 0 km/h (mph), Maximum: 300 km/h (186.4 mph)    		 0 km/h (mph): Vehicle stopped -
    Vehicle driven at constant speed No significant fluctuation
    Engine Revolution Engine revolution:
    Minimum: 0 RPM, Maximum: 12800 RPM    		 Engine running at constant speed No significant fluctuation
    Motor Actual Current Current to motor:
    Minimum: -327.68 A, Maximum: 327.67 A    		 Value changes in proportion to steering effort -
    Command Value Current Requested current to motor:
    Minimum: -327.68 A, Maximum: 327.67 A    		 Value changes in proportion to steering effort -
    Steering Angle Velocity Steering angle speed:
    Minimum: -32768 deg/s, Maximum: 32767 deg/s    		 Value changes in proportion to steering effort The engine is running and steering wheel is being turned
    Thermistor Temperature ECU substrate temperature:
    Minimum: -40°C, Maximum: 150°C    		 - -
    PIG Power Supply Power source voltage to activate motor:
    Minimum: 0 V, Maximum: 20.1531 V    		 11 to 14 V: Always -
    IG Power Supply ECU power source voltage:
    Minimum: 0 V, Maximum: 20.1531 V    		 11 to 14 V: Ignition switch ON -
    Steering Wheel Torque Steering Wheel Torque:
    Minimum: -327.68 Nm, Maximum: 7 Nm    		 Value changes in proportion to steering effort Ignition switch ON and power steering is operating
    Motor Rotation Angle Motor rotation angle:
    Minimum: 0 deg, Maximum: 1441.77 deg    		 During steering operation, motor rotation angle value changes from 0 to 360° The engine is running and steering wheel is being turned
    Motor Voltage Motor Power Supply Voltage:
    Minimum: 0 V, Maximum: 98 V    		 11 to 14 V: Ignition switch ON -
    Motor Terminal Volt(U) Motor terminal voltage (U phase):
    Minimum: 0 V, Maximum: 98 V    		 Value changes within 4 to 35 V range The engine is running and steering wheel is being turned.
    Motor Terminal Volt(V) Motor terminal voltage (V phase):
    Minimum: 0 V, Maximum: 98 V    		 Value changes within 4 to 35 V range The engine is running and steering wheel is being turned.
    Motor Terminal Volt(W) Motor terminal voltage (W phase):
    Minimum: 0 V, Maximum: 98 V    		 Value changes within 4 to 35 V range The engine is running and steering wheel is being turned.
    Torque Sensor 1 Output Torque sensor 1 output value:
    Minimum: 0 V, Maximum: 4.9725 V    		 2.3 to 2.7 V The engine is running and steering wheel is not turned (without load).
    2.5 to 3.8 V The engine is running and steering wheel is turned to right with vehicle stopped.
    1.2 to 2.5 V The engine is running and steering wheel is turned to left with vehicle stopped.
    Torque Sensor 2 Output Torque sensor 2 output value:
    Minimum: 0 V, Maximum: 4.9725 V    		 2.3 to 2.7 V The engine is running and steering wheel is not turned (without load).
    1.2 to 2.5 V The engine is running and steering wheel is turned to right with vehicle stopped.
    2.5 to 3.8 V The engine is running and steering wheel is turned to left with vehicle stopped.
    IG ON/OFF Times Number of times ignition switch turned to ON after DTC detection:
    Minimum: 0 times, Maximum: 65535 times    		 - -
    Motor Overheat Record Continuous overheat prevention control record:
    Unrec or Rec    		 Unrec -
    Motor Lo Power Record PIG power source voltage drop record:
    Unrec or Rec    		 Unrec -
    Eng Rev Inter Record Status of the Record of Engine Revolution Signal Interrupt:
    Unrec or Rec    		 Unrec -
    Spd Sig Invalid Record Record of vehicle speed signal invalid:
    Unrec or Rec    		 Unrec -
    Battery Voltage Lo Record Battery voltage drop record:
    Minimum: 0 times, Maximum: 65535 times    		 0 times -
    Battery Voltage Battery voltage:
    Minimum: 0 V, Maximum: 25.5 V    		 11 to 14 V: Always -
    PS Assist Signal Status of the Record of Power Steering Assist Signal:
    ON or OFF    		 ON or OFF -
    The Number of DTCs Number of detected DTCs when freeze frame data stored:
    Minimum: 0, Maximum: 255    		 - -
scientia non olet · About LEMON Manuals