Data List / Active Test

HINT: 

Using the Techstream to read the Data List allows values or status of switches, sensors, actuators and other items to be read without removing any parts. This non-intrusive inspection can be very useful because intermittent conditions or signals may be discovered before parts or wiring is disturbed. Reading the Data List information early in troubleshooting is one way to save diagnostic time.

1. Connect the Techstream to the DLC3.
2. Turn the ignition switch to ON.
3. Turn the Techstream on.
4. Enter the following menus.
   1. Select: Body Electrical / D-Door Motor / Data List.
      D-DOOR MOTOR:
      
      

      Tester Display	Measurement Item/Range	Normal Condition	Diagnostic Note
      D Door P/W Auto SW	Driver door power window auto switch signal/ON or OFF	ON: Driver door power window auto switch operates OFF: Driver door power window auto switch does not operate	-
      D Door P/W Up SW	Driver door power window manual up switch signal/ON or OFF	ON: Driver door power window manual up switch operates OFF: Driver door power window manual up switch does not operate	-
      D Door P/W Down SW	Driver door power window manual down switch signal/ON or OFF	ON: Driver door power window manual down switch operates OFF: Driver door power window manual down switch does not operate	-
      Glass Position (Close - 1/4)	Jam protection operation within range of fully closed to 1/4 open window glass position/OK or CAUTION	OK: Margin is sufficient during manual UP operation CAUTION: May be displayed even when no resistance is applied in each position. In this case, there is a foreign object stuck in that position.	-
      Glass Position (1/4 - 2/4)	Jam protection operation within range of 1/4 to 1/2 open window glass position/OK or CAUTION	OK: Margin is sufficient during manual UP operation CAUTION: May be displayed even when no resistance is applied in each position. In this case, there is a foreign object stuck in that position.	-
      Glass Position (2/4 - 3/4)	Jam protection operation within range of 1/2 to 3/4 open window glass position/OK or CAUTION	OK: Margin is sufficient during manual UP operation CAUTION: May be displayed even when no resistance is applied in each position. In this case, there is a foreign object stuck in that position.	-
      Glass Position (3/4 - Open)	Jam protection operation within range of 3/4 to fully open window glass position/OK or CAUTION	OK: Margin is sufficient during manual UP operation CAUTION: May be displayed even when no resistance is applied in each position. In this case, there is a foreign object stuck in that position.	-
      Number of Trouble Codes	Number of DTC recorded / 0 to 255	Min.: 0 Max.: 255	-

   2. Select: Body Electrical / Main Body / Data List.
      MAIN BODY:
      
      

      Tester Display	Measurement Item/Range	Normal Condition	Diagnostic Note
      Communication D Door Motor	Connection status between power window regulator motor assembly (driver door) and main body ECU (Instrument panel junction block)/OK/Stop	OK: Communication is normal STOP: Communication is stopped	-
      D Door Courtesy SW	Driver side door courtesy switch signal/ON or OFF	ON: Driver side door is open OFF: Driver side door is closed	-

HINT: 

Using the Techstream to perform Active Test allows relays, VSVs, actuators and other items to be operated without removing any parts. This non-intrusive functional inspection can be very useful because intermittent operation may be discovered before parts or wiring is disturbed. Performing Active Test early in troubleshooting is one way to save diagnostic time. Data List information can be displayed while performing Active Test.

1. Connect the Techstream to the DLC3.
2. Turn the ignition switch to ON.
3. Turn the Techstream on.
4. Enter the following menus.
   1. Select: Body Electrical / D-Door Motor / Active Test.
      D-DOOR MOTOR:
      
      

      Tester Display	Test Part	Control Range	Diagnostic Note
      Power Window	Power window	UP or OFF	-
      Power Window	Power window	DOWN or OFF	-

   2. Select: Body Electrical / Main Body / Active Test.
      MAIN BODY:
      
      

      Tester Display	Test Part	Control Range	Diagnostic Note
      IG OFF P/W Control Permission Output	Power window	ON or OFF (After ignition switch is turned off)	-