Common Specs & Procedures
COROLLA COMMON SPECS & PROCEDURES
| System | Specification/Procedure | |||
|---|---|---|---|---|
| Air Conditioning | ||||
| Service | SERVICE DATA | |||
| Torque | TORQUE SPECIFICATIONS | |||
| Axle Nut/Hub Nut | ||||
| Front Axle Nut | 216 N.m (158 ft.lbs) | |||
| Rear Hub Bolts | 100 N.m (74 ft.lbs) | |||
| Battery | ||||
| 2AZ-FE | SERVICE DATA | |||
| 2ZR-FE | SERVICE DATA | |||
| Brakes | ||||
| Bleeding Sequence | BLEEDING | |||
| Front | SERVICE DATA | |||
| Torque | TORQUE SPECIFICATIONS | |||
| Rear | SERVICE DATA | |||
| Torque | TORQUE SPECIFICATIONS | |||
| Charging | ||||
| 2AZ-FE | ||||
| Generator | SERVICE DATA | |||
| Torque | TORQUE SPECIFICATIONS | |||
| 2ZR-FE | ||||
| Generator | SERVICE DATA | |||
| Torque | TORQUE SPECIFICATIONS | |||
| Drive Belts | ||||
| 2AZ-FE | ||||
| Belt Routing | INSTALLATION | |||
| Belt Tensioning | ON-VEHICLE INSPECTION | |||
| 2ZR-FE | ||||
| Belt Routing | ON-VEHICLE INSPECTION | |||
| Belt Tensioning | ON-VEHICLE INSPECTION | |||
| Engine Cooling | ||||
| 2AZ-FE | ||||
| General Service Specifications | SERVICE DATA | |||
| Radiator Cap Pressure | 74 to 103 kPa (0.75 to 1.05 kgf/cm2
, 10.7 to 15 psi) Minimum 59 kPa (0.6 to 2 , 8.6) |
|||
| Thermostat R & I | THERMOSTAT | |||
| Water Pump R & I | WATER PUMP | |||
| 2ZR-FE | ||||
| General Service Specifications | SERVICE DATA | |||
| Radiator Cap Pressure | 74 to 103 kPa (0.75 to 1.05 kgf/cm2
, 10.7 to 14.9 psi) Minimum 59 kPa (0.6 to 2 , 8.6) |
|||
| Thermostat R & I | THERMOSTAT | |||
| Water Pump R & I | WATER PUMP | |||
| Engine Mechanical | ||||
| 2AZ-FE | ||||
| Compression | SERVICE DATA | |||
| Oil Pressure | ||||
| @ Idle: | 29 kPa (0.3 kgf.cm2 , 4.3 psi) or more | |||
| @ 3,000 RPM: | 170 to 300 kPa (1.7 to 3.1 kgf/cm2 , 24 to 44 psi) | |||
| Overhaul | SERVICE DATA | |||
| Torque | TORQUE SPECIFICATIONS | |||
| 2ZR-FE | ||||
| Compression | SERVICE DATA | |||
| Oil Pressure | ||||
| @ Idle: | 25 kPa (0.3 kgf/cm2 , 3.6 psi) or more | |||
| @ 3,000 RPM: | 150 to 400 kPa (1.5 to 4.1 kgf/cm2 , 22 to 58 psi) | |||
| Overhaul | SERVICE DATA | |||
| Torque | TORQUE SPECIFICATIONS | |||
| Fluid Specifications | See FLUIDS under MAINTENANCE tab. | |||
| Flywheel/Flex Plate Torque | ||||
| 2AZ-FE | ||||
| Flywheel | 130 N.m (96 ft.lbs) | |||
| Flex Plate (Drive Plate) | 98 N.m (72 ft.lbs) | |||
| 2ZR-FE | ||||
| Flywheel | Step 1: 49 N.m (36 ft.lbs) Step 2: Turn 90° |
|||
| Drive Plate | 88 N.m (65 ft.lbs) | |||
| Fuel System | ||||
| 2AZ-FE | ||||
| Pressure Specification | 304 to 343 kPa (3.1 to 3.5 kgf/cm2 , 44.1 to 49.7 psi) | |||
| Fuel Pressure Test Procedure | ON-VEHICLE INSPECTION | |||
| Fuel Filter Location | FUEL PUMP | |||
| 2ZR-FE | ||||
| Pressure Specification | 304 to 343 kPa (3.1 to 3.5 kgf/cm2 , 44.1 to 49.7 psi) | |||
| Fuel Pressure Test Procedure | ON-VEHICLE INSPECTION | |||
| Fuel Filter Location | FUEL PUMP | |||
| Ignition | ||||
| Firing Order, Cylinder Identification |
FIRING ORDER & CYLINDER IDENTIFICATION | |||
| Spark Plug | ||||
| 2AZ-FE | ||||
| Type | DENSO: SK20R11 NGK: IFR6A11 |
|||
| Gap | 1.0 to 1.1 mm (0.0394 to 0.0433 in.) | |||
| Torque | 19 N.m (194 kgf.cm, 14 ft.lbf) | |||
| 2ZR-FE | ||||
| Type | DENSO: SC20HR11 | |||
| Gap | 1.0 to 1.1 mm (0.0394 to 0.0433 in.) | |||
| Torque | 20 N.m (204 kgf.cm, 15 ft.lbs) | |||
| Starting | ||||
| 2AZ-FE | ||||
| Starter | SERVICE DATA | |||
| Torque | TORQUE SPECIFICATIONS | |||
| 2ZR-FE | ||||
| Starter | SERVICE DATA | |||
| Torque | TORQUE SPECIFICATIONS | |||
| Wheel Alignment | ||||
| Front | ||||
| Adjustment Specifications | SERVICE DATA | |||
| Torque | TORQUE SPECIFICATIONS | |||
| Rear | ||||
| Adjustment Specifications | SERVICE DATA | |||
| Torque | TORQUE SPECIFICATIONS | |||
| Wheel & Tire | ||||
| Wheel Lug Nut Torque | 103 N.m (1,150 kgf.cm, 76 ft.lbs) | |||