LEMON Manuals: Even more car manuals for everyone
Home >> Toyota >> 2009 >> Tacoma PreRunner, 2D Pickup >> Repair and Diagnosis >> Engine Performance >> Engine Ignition System (2TR-FE) >> Ignition System >> On-Vehicle Inspection

On-Vehicle Inspection

NOTE: In this section, the terms "cold" and "hot" refer to the temperature of the coils. "Cold" means approximately - 10 to 50°C (14 to 122°F). "Hot" means approximately 50 to 100°C (122 to 212°F).
  1. PERFORM SPARK TEST 
    1. Check for DTCs.
      NOTE: If a DTC is present, perform troubleshooting procedures for that DTC.
    2. Check if sparks occur.
      1. Remove the ignition coil.
      2. Remove the spark plug.
      3. Install the spark plug to the ignition coil and connect the ignition coil connector.
      4. Disconnect the 4 injector connectors.
      5. Ground the spark plug.
      6. Visually check that sparks occur while the engine is being cranked.
        NOTE:
        • Be sure to ground the spark plug when checking.
        • If the ignition coil has been struck or dropped, replace it.
        • Do not crank the engine for more than 2 seconds.
    3. Spark test flow chart.
      1. Check that the wire harness side connector of the ignition coil with igniter is securely connected.

        Result 

        RESULT CHART

        Result Proceed to
        NG Connect securely
        OK Go to next step
      2. Perform spark test on each ignition coil with igniter.
        1. Replace ignition coil with igniter with a normal one.
        2. Perform spark test again.

          Result 

          RESULT CHART

          Result Proceed to
          OK Replace Ignition coil with Igniter
          NG Go to next step
      3. Check power supply to ignition coil with igniter.
        1. Turn the ignition switch ON.
        2. Check that there is battery voltage at ignition coil positive (+) terminal.

          Result 

          RESULT CHART

          Result Proceed to
          NG Check wiring between engine switch and Ignition coil with igniter
          OK Go to next step
      4. Check resistance of camshaft position sensor.

        Standard resistance 

        TEMPERATURE CHART

        Temperature Specified Condition
        Cold 835 to 1,400 Ω
        Hot 1,060 to 1,645 Ω

        Result 

        RESULT CHART

        Result Proceed to
        NG Replace camshaft position sensor
        OK Go to next step
      5. Check resistance of crankshaft position sensor.

        Standard resistance 

        TEMPERATURE CHART

        Temperature Specified Condition
        Cold 1,690 to 2,740 Ω
        Hot 2,065 to 3,225 Ω

        Result 

        RESULT CHART

        Result Proceed to
        NG Replace crankshaft position sensor.
        OK Go to next step
      6. Check IGT signal from ECM.

        Result 

        RESULT CHART

        Result Proceed to
        NG Check ECM
        OK Repair wiring between ignition coil and ECM
    4. Using a 16 mm plug wrench, install the spark plug.

      Torque: 18 N*m (183 kgf*cm, 13 ft.*lbf) 

    5. Install the ignition coil.

      Torque: 9.0 N*m (92 kgf*cm, 80 in.*lbf) 

  2. CHECK SPARK PLUG 
    NOTE:
    • Do not use a wire brush for cleaning.
    • Do not attempt to adjust the electrode gap of a used spark plug.
    1. Check the electrode.
      1. Using a megohmmeter, measure the insulation resistance.

        Insulation resistance: 10 MΩ or more 

        HINT:

        If a megohmmeter is not available, perform the following simple inspection instead.

        Fig 1: Measuring Insulation Resistance
        G06086077Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
    2. Alternative inspection method:
      1. Quickly accelerate the engine to 4,000 rpm 5 times.
      2. Remove the spark plug.
      3. Visually check the spark plug.

        If the electrode is dry, the spark plug is functioning properly. If the electrode is damp, proceed to the next step.

    3. Check the spark plug for any damage on its thread and insulator.
      Fig 2: Identifying Spark Plug Condition
      G05109914Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002

      If there is damage, replace the spark plug. If not, reinstall the spark plug.

      Recommended spark plug 

      MANUFACTURER CHART

      Manufacturer Spark Plug Type
      DENSO made SK20R11
      NGK made ILFR6C11
    4. Check the spark plug electrode gap.

      Maximum electrode gap for used spark plug: 

      1.3 mm (0.051 in.) 

      If the gap is greater than the maximum, replace the spark plug. 

      Electrode gap for new spark plug: 

      1.1 mm (0.043 in.) 

      NOTE: When adjusting the gap of a new spark plug, bend only the base of the ground electrode. Do not touch the tip. Never attempt to adjust the gap of a used plug.
      Fig 3: Checking Spark Plug Electrode Gap
      G06086079Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
    5. Clean the spark plugs.

      If the electrode has traces of wet carbon, clean the electrode with a spark plug cleaner and then dry it.

      Air pressure: 

      588 kPa (6 kgf/cm 2  , 85 psi) 

      Duration: 

      20 seconds or less 

      HINT:

      Only use the spark plug cleaner when the electrode is free of oil. If the electrode has traces of oil, use gasoline to clean off the oil before using the spark plug cleaner.

      Fig 4: Cleaning Spark Plugs
      G06086080Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
scientia non olet · About LEMON Manuals