Door Control Receiver: Installation

INSTALL DOOR CONTROL RECEIVER
1. Install the receiver with the bolt.
2. Connect the receiver connector.
Fig 1: Identifying Door Control Receiver Bolt
Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
INSTALL INNER ROOF SIDE GARNISH ASSEMBLY RH (w/o Rear No. 2 Seat)
1. Attach the 7 clips to install the garnish.
Fig 2: Identifying Garnish Clips
Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
INSTALL INNER ROOF SIDE GARNISH ASSEMBLY RH (w/ Rear No. 2 Seat)
1. Attach the 7 slips to install the garnish.
2. Connect the rear No. 2 seat belt's shoulder anchor.
  1. Connect the shoulder anchor with the bolt.
    Torque: 42 N*m (428 kgf*cm, 31 ft.*lbf)
    
    Fig 3: Identifying Garnish Clips
    Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
  2. Attach the claws to close the seat belt anchor cover.
INSTALL DECK TRIM SIDE PANEL ASSEMBLY RH (w/o Rear No. Seat) (See INSTALLATION )
INSTALL DECK TRIM SIDE PANEL ASSEMBLY RH (w/ Rear No. 2 Seat) (See INSTALLATION )

Fig 4: Attaching Seat Belt Anchor Cover
Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
INSTALL TETHER ANCHOR BRACKET SUB-ASSEMBLY (w/o Rear No. 2 Seat)
1. Install the tether anchor bracket with the bolt.
INSTALL RECLINING REMOTE CONTROL LEVER BEZEL RH (w/o Rear No. 2 Seat) (See REAR NO. 2 SEAT ASSEMBLY )
INSTALL REAR DECK TRIM COVER RH (w/ Rear No. 2 Seat)
1. Attach the 4 claws to install the trim cover.
2. Install the belt.
Fig 5: Identifying Tether Anchor Bracket Bolt
Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
INSTALL REAR FLOOR FINISH PLATE (See INSTALLATION )
INSTALL REAR FLOOR NO. 1 MAT SUPPORT SIDE PLATE (See INSTALLATION )
INSTALL REAR FLOOR NO. 3 BOARD
INSTALL REAR FLOOR NO. 2 BOARD
INSTALL REAR NO. 2 SEAT ASSEMBLY LH (w/ Rear No. 2 Seat) (See INSTALLATION )
INSTALL REAR NO. 2 SEAT ASSEMBLY RH (w/ Rear No. 2 Seat)
HINT:

Use the same procedures described for the LH side.
INSTALL NO. 2 SEAT LEG COVER LH (w/ Rear No. 2 Seat) (See POWER SEAT SWITCH )
INSTALL NO. 2 SEAT LEG COVER RH (w/ Rear No. 2 Seat)
HINT:

Use the same procedures described for the LH side.
INSTALL NO. 2 SEAT HINGE COVER LH (w/ Rear No. 2 Seat) (See POWER SEAT SWITCH )
INSTALL NO. 2 SEAT HINGE COVER RH (w/ Rear No. 2 Seat)
HINT:

Use the same procedures described for the LH side.
INSTALL DECK BOARD ASSEMBLY (w/o Rear No. 2 Seat)
INSTALL REAR FLOOR NO. 1 BOARD (w/o Rear No. 2 Seat)
INSTALL REAR DOOR OPENING TRIM WEATHERSTRIP RH
INSTALL REAR DOOR SCUFF PLATE RH
1. Attach the 9 claws and 2 clips to install the scuff plate.
Fig 6: Identifying Scuff Plate Claws And Clips
Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002