LEMON Manuals: Even more car manuals for everyone
Home >> Toyota >> 2009 >> Matrix Base, Standard >> Repair and Diagnosis >> External Pages >> Different variant/trim >> Section 13 (Automatic Transmission - U250E) >> Transmission Control Cable >> Removal

Transmission Control Cable: Removal

WARNING: This page is about a different variant/trim than selected.
  1. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL 
  2. REMOVE CENTER INSTRUMENT CLUSTER FINISH PANEL SUB-ASSEMBLY  (See REMOVAL )
  3. REMOVE SHIFT LEVER KNOB SUB-ASSEMBLY  (See REMOVAL )
  4. REMOVE CENTER INSTRUMENT CLUSTER FINISH PANEL ASSEMBLY  (See REMOVAL )
  5. REMOVE FRONT UPPER CONSOLE BOX  (See REMOVAL )
  6. REMOVE NO. 2 SWITCH HOLE BASE  (See REMOVAL )
  7. REMOVE CONSOLE BOX CARPET 
  8. REMOVE FRONT CONSOLE BOX ASSEMBLY  (See REMOVAL )
  9. REMOVE FRONT NO. 1 CONSOLE BOX INSERT  (See REMOVAL )
  10. REMOVE FRONT NO. 2 CONSOLE BOX INSERT  (See REMOVAL )
  11. REMOVE LOWER CENTER INSTRUMENT PANEL FINISH PANEL  (See REMOVAL )
  12. REMOVE NO. 1 ENGINE COVER SUB-ASSEMBLY  (See REMOVAL )
  13. REMOVE AIR CLEANER CAP SUB-ASSEMBLY  (See REMOVAL )
  14. REMOVE AIR CLEANER CASE  (See REMOVAL )
  15. REMOVE BATTERY  (See REMOVAL )
  16. REMOVE BATTERY CARRIER  (See REMOVAL )
  17. REMOVE CENTER EXHAUST PIPE ASSEMBLY  (See REMOVAL )
  18. REMOVE FRONT NO. 1 FLOOR HEAT INSULATOR 
    1. Remove the 3 nuts and front No. 1 floor heat insulator.
      Fig 1: Locating Front No. 1 Floor Heat Insulator Nuts
      G06011533Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
  19. REMOVE TRANSMISSION CONTROL CABLE ASSEMBLY 
    1. Move the shift lever to N.
    2. Disconnect the end of the transmission control cable assembly from the shift lever assembly.
      Fig 2: Locating Transmission Control Cable Bolt
      G06043200Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
    3. Pull out the stopper of the transmission control cable.
      NOTE: Do not remove the stopper. If the stopper is removed, reinstall it to its original position.
      Fig 3: Pulling Out Stopper Of Transmission Control Cable
      G06043201Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
    4. Rotate the nut counterclockwise approximately 180° and, while holding the nut in that position, disconnect the transmission control cable from the shift lever retainer.
      NOTE: Do not over-rotate the nut as it will come off the internal spring and the transmission control cable will not be reusable.
    5. Remove the nut and disconnect the control cable assembly from the control shaft lever.
      Fig 4: Locating Transmission Control Cable Nut
      G06011483Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
    6. Remove the clip and disconnect the transmission control cable assembly from the control cable bracket.
    7. Disconnect the control cable assembly from the control cable bracket.
      Fig 5: Locating Control Cable Assembly
      G06008385Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
    8. Remove the nut and separate the transmission control cable support.
      Fig 6: Locating Transmission Control Cable Support With Nut
      G06011537Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
    9. Remove the 2 nuts and separate the transmission control cable assembly.
      Fig 7: Locating Transmission Control Cable Assembly Nuts
      G06011538Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
    10. Pull out the transmission control cable assembly.
scientia non olet · About LEMON Manuals