Automatic Transmission Unit: Reassembly

Fig 1: Exploded View Of Bearing

Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002

Bearing diameter 

1. Coat 2 new O-rings with ATF, and install them onto the brake reaction sleeve.
Fig 2: Identifying O-Ring
Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
2. Coat 2 new O-rings with ATF, and install them onto the No. 4 brake piston.
3. Install the No. 4 brake piston onto the reaction sleeve.

1. Coat a new O-ring with ATF, and install it to the reaction sleeve.
Fig 3: Identifying Brake Reaction Sleeve
Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
2. With the No. 1 brake piston underneath (the rear side), install the brake reaction sleeve and No. 1 brake piston onto the transmission case.
   NOTE: Be careful not to damage the O-rings.

1. Coat a new O-ring with ATF.
2. Install the O-ring onto the 1st and reverse brake piston.
Fig 4: Identifying 1st And Reverse Brake Piston
Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
3. With the spring seat of the piston facing upward (the front side), place the piston in the transmission case.
   NOTE: Be careful not to damage the O-ring.
4. Place the piston return spring onto the 1st and reverse brake piston.
   Fig 5: Identifying Piston Return Spring Onto 1st And Reverse Brake Piston

   Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002

1. Place SST on the spring retainer, and compress the return spring.

   SST 09350-30020 (09350-07050) 

   Fig 6: Identifying Return Spring

   Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
2. Using SST, install the snap ring.

   SST 09350-30020 (09350-07070) 

1. Install the thrust needle roller bearing.

   Thrust needle roller bearing diameter 

   THRUST NEEDLE ROLLER BEARING DIAMETER SPECIFICATION
   
   

   Item	Inside	Outside
   Thrust needle roller bearing	45.9 mm (1.807 in.)	64.0 mm (2.520 in.)

   Fig 7: Identifying Thrust Needle Roller Bearing

   Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
2. Install the thrust needle roller bearing.
3. Coat the No. 9 thrust bearing race with petroleum jelly, and install it onto the rear planetary ring gear.

   Bearing and race diameter 

   BEARING AND RACE DIAMETER SPECIFICATION
   
   

   Item	Inside	Outside
   Bearing	21.5 mm (0.847 in.)	40.8 mm (1.606 in.)
   Race	48.5 mm (1.909 in.)	62.7 mm (2.469 in.)

   Fig 8: Identifying Thrust Needle Roller Bearing And Race

   Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
4. Install the rear planetary gear assembly.
   Fig 9: Identifying Rear Planetary Gear Assembly

   Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002

1. Make sure the 1st and reverse brake pistons move smoothly when applying and releasing the compressed air into the transmission case.
   Fig 10: Identifying Compressed Air Into Transmission Case

   Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
2. Using vernier calipers, measure the level difference (length A) between the upper surface of the 1st and reverse brake piston and the hitting surface of the No. 4 brake flange at both ends across a diameter, and calculate the average.
   NOTE: The 1st and reverse brake piston must be installed tightly to the end face of the transmission case.

   HINT:

   Length A = 36.35 to 37.09 mm (1.431 to 1.460 in.)

   Fig 11: Identifying Level Difference (Length A) Between Upper Surface Of 1st And Reverse Brake Piston

   Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
3. Using vernier calipers, measure the thickness (length B) of the 2 brake flanges, the 7 No. 4 brake plates and the 8 No. 4 brake discs altogether at both ends across a diameter, and calculate the average.

   HINT:

   Pack clearance = Length A - Length B - 0.25 mm - 1.8 mm

   Length B = 36.04 to 37.14 mm (1.419 to 1.462 in.)

   Pack clearance: 

   0.8 to 1.1 mm (0.031 to 0.043 in.) 

   Fig 12: Identifying Thickness (Length B) Of Brake Flanges

   Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
4. If the pack clearance is outside the standard, select and install a brake flange that makes the pack clearance within the standard.

   H thickness 

   BRAKE FLANGES THICKNESS SPECIFICATION
   
   

   No.	Thickness	No.	Thickness
   0	0 mm (0 in.)	8	0.8 mm (0.032 in.)
   2	0.2 mm(0.008 in.)	10	1.0 mm (0.039 in.)
   4	0.4 mm (0.016 in.)	12	1.2 mm (0.047 in.)
   6	0.6 mm (0.024 in.)	14	1.4 mm (0.055 in.)

1. Install the 7 plates, 8 discs and 2 flanges.

   Install in order: 

   F - D - P - D - P - D - P - D - P - D - P - D - P - D - P - D - F 

   HINT:

   P = Plate, D = Disc, F = Flange

   Fig 13: Identifying No. 4 Brake Disc

   Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002

1. Install the brake stopper spring.
   Fig 14: Identifying Brake Stopper Spring

   Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002

1. Install the No. 8 thrust bearing race, thrust needle roller bearing, No. 7 thrust bearing race and planetary ring gear flange onto the intermediate shaft.

   Bearing and race diameter mm (in.) 

   BEARING AND RACE DIAMETER SPECIFICATION
   
   

   Item	Inside	Outside
   No. 7 thrust bearing race	33.4 (1.315)	49.0 (1.929)
   Thrust needle roller bearing	32.1 (1.264)	49.35 (1.943)
   No. 8 thrust bearing race	32.1 (1.264)	49.0 (1.929)

   Fig 15: Identifying No. 8 Thrust Bearing Race, Thrust Needle Roller Bearing And No. 7 Thrust Bearing Race

   Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002

1. Install the No. 3 1-way clutch assembly and the 1-way clutch inner race onto the intermediate shaft.
   Fig 16: Identifying No. 3 1-Way Clutch Assembly And 1-Way Clutch Inner Race

   Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002

1. Install the intermediate shaft with the No. 3 1-way clutch assembly onto the case.
   Fig 17: Identifying Intermediate Shaft

   Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
2. Using SST, install the snap ring.

   SST 09350-30020 (09350-07050, 09350-07060) 

   Fig 18: Identifying Snap Ring

   Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002

1. Install the center planetary gear assembly and planetary sun gear into the case.
2. Coat the No. 4 thrust bearing race and thrust needle roller bearing with petroleum jelly, and install them onto the center planetary ring gear.

   Race and Bearing diameter 

   RACE AND BEARING DIAMETER SPECIFICATION
   
   

   Item	Inside	Outside
   Race	53.7 mm (2.114 in.)	74.0 mm (2.913 in.)
   Bearing	55.7 mm (2.192 in.)	76.4 mm (3.008 in.)

   Fig 19: Identifying Planetary Sun Gear, Thrust Needle Roller Bearing And No. 4 Thrust Bearing Race

   Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002

1. Coat 2 new O-rings with ATF, and install them onto the No. 2 brake piston.
Fig 20: Identifying O-Ring
Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
2. Be careful not to damage the O-rings. Press the No. 2 brake piston into the No. 2 brake cylinder with both hands.
3. Install the No. 2 brake piston onto the case.

1. Install the flange, 3 plates, 3 discs and brake piston return spring.

   Install in order: 

   F - D- P- D- P- D- P 

   HINT:

   P = Plate, D = Disc, F = Flange

   Fig 21: Identifying Flange, Plates And Discs

   Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
2. Using SST and press, install the No. 2 brake spring snap ring.

   SST 09351-40010 

   Fig 22: Identifying No. 2 Brake Spring Snap Ring

   Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002

1. Coat 2 new O-rings with ATF, and install them onto the No. 1 brake piston.
Fig 23: Identifying O-Ring
Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
2. Be careful not to damage the O-rings. Press the No. 1 brake piston into the No. 1 brake cylinder with both hands.

1. Install the brake piston return spring and No. 1 brake piston with the No. 1 brake cylinder into the transmission case.
   Fig 24: Identifying Brake Piston Return Spring Sub-Assembly

   Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002

1. Using SST and a press, install the brake piston return spring snap ring.

   SST 09351-40010 

   Fig 25: Identifying Brake Piston Return Spring Snap Ring

   Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002

1. Install the 3 plates, 3 discs and flange.

   Install in order: 

   F - D - P - D - P - D - P 

   HINT:

   P = Plate, D = Disc, F = Flange

   Fig 26: Identifying Plate, Disc And Flange

   Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002

1. Install the center planetary ring gear and front planetary ring gear flange into the front planetary ring gear.
   Fig 27: Identifying Center Planetary Ring Gear And Front Planetary Ring Gear Flange

   Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
2. Using a screwdriver, install the snap ring.
   Fig 28: Identifying Snap Ring

   Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002

1. Install the front planetary ring gear into the case.
   Fig 29: Identifying Front Planetary Ring Gear

   Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002

1. Install the thrust needle roller bearing and No. 2 planetary carrier thrust washer.
Fig 30: Identifying Thrust Needle Roller Bearing And No. 2 Planetary Carrier Thrust Washer
Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
2. Coat the No. 3 thrust bearing race with petroleum jelly, and install it onto the front planetary ring gear.

   Thrust needle roller bearing and race diameter 

   THRUST NEEDLE ROLLER BEARING AND RACE DIAMETER SPECIFICATION
   
   

   Item	Inside	Outside
   Thrust needle roller bearing	43.4 mm (1.709 in.)	58.3 mm (2.295 in.)
   Race	38.0 mm (1.496 in.)	57.0 mm (2.244 in.)

3. Install the front planetary gear assembly and 1 -way clutch inner race into the case.
   Fig 31: Identifying Front Planetary Gear Assembly And 1 -Way Clutch Inner Race

   Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002

1. Make sure the No. 1 brake piston moves smoothly when applying and releasing the compressed air into the transmission case.
   Fig 32: Identifying Compressed Air Into Transmission Case

   Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
2. Using a feeler gauge, measure the B3 brake pack clearance between the snap ring and flange.

   Piston stroke: 

   0.42 to 0.72 mm (0.017 to 0.028 in.) 

   If the piston stroke is outside the specification, parts may have been assembled incorrectly.

   Perform the reassembly again.

   If the piston stroke is still outside the specification, select another flange.

   HINT:

   There are 4 different thicknesses for the flange.

   Fig 33: Identifying Brake Pack Clearance Between Snap Ring And Flange

   Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002

   Flange thickness 

   FLANGE THICKNESS SPECIFICATION
   
   

   No.	Thickness	No.	Thickness
   0	2.0 mm (0.079 in.)	2	2.4 mm (0.094 in.)
   1	2.2 mm (0.087 in.)	3	2.6 mm (0.102 in.)

1. Coat 2 new O-rings with ATF, and install them onto the 2nd brake piston.
Fig 34: Identifying O-Ring
Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
2. Be careful not to damage the O-rings. Press the 2nd brake cylinder into the 2nd brake piston with both hands.
3. Using SST and press, install the snap ring.

   SST 09351-40010 

   NOTE: Make sure that the end gap of the snap ring is not aligned with the spring retainer claw.
   Fig 35: Identifying Snap Ring

   Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002

1. Install the 2nd brake cylinder into the case.
   Fig 36: Identifying 2nd Brake Cylinder

   Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002

1. Install the 1-way clutch assembly and the thrust washer into the case.
   Fig 37: Identifying 1-Way Clutch Assembly And Thrust Washer

   Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002

1. Using SST, install the snap ring.

   SST 09350-30020 (09350-07060) 

   Fig 38: Identifying Snap Ring

   Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002

1. Install the flanges, 4 discs, 4 plates and the cushion plate onto the case.

   Install in order: 

   F - D - P - D - P - D - P - D - P - C 

   HINT:

   P = Plate, D = Disc, F = Flange C = Cushion

   Fig 39: Identifying Plate, Disc, Flange And Cushion

   Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002

1. Using a screwdriver, install the snap ring.
   Fig 40: Identifying No. 3 Brake Snap Ring

   Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002

1. Coat the race with petroleum jelly and install it onto the No. 2 clutch drum thrust washer.
2. Install the No. 2 1-way clutch assembly washer.
   Fig 41: Identifying No. 2 1-Way Clutch Assembly

   Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002

1. Install the thrust needle roller bearing.
2. Coat the race with petroleum jelly and install it onto the clutch drum thrust washer.

   Thrust needle roller bearing and diameter 

   THRUST NEEDLE ROLLER BEARING AND DIAMETER SPECIFICATION
   
   

   Item	Inside	Outside
   Thrust needle roller bearing	71.9 mm (2.831 in.)	85.6 mm (3.370 in.)
   Race	73.6 mm (2.898 in.)	102.0 mm (4.016 in.)

3. Install the clutch drum thrust washer and race onto the clutch drum and input shaft assembly.
   Fig 42: Identifying Clutch Drum And Input Shaft Assembly

   Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
4. Install the input shaft sub-assembly with the direct and reverse multiple disc assembly onto the transmission case.
   Fig 43: Identifying Input Shaft Sub-Assembly

   Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002

1. Install the No. 1 thrust bearing race onto the front oil pump.

   No. 1 thrust bearing race diameter 

   THRUST BEARING RACE DIAMETER SPECIFICATION
   
   

   Item	Inside	Outside
   Race	74.2 mm (2.921 in.)	87.74 mm (3.454 in.)

   Fig 44: Identifying No. 1 Thrust Bearing Race

   Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
2. Coat a new O-ring with ATF, and install it onto the oil pump assembly.
Fig 45: Identifying O-Ring
Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
3. Place the oil pump through the input shaft, and align the bolt holes in the oil pump assembly with the transmission case.
4. Hold the input shaft, and lightly press the oil pump body to slide the oil seal rings into the overdrive direct clutch drum.
   NOTE: Do not push on the oil pump strongly, as the oil seal ring will stick to the direct clutch drum.
5. Install the 10 bolts.

   Torque: 21 N*m (214 kgf*cm, 15 ft.*lbf) 

   Fig 46: Identifying Oil Pump Bolts

   Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002

1. Using SST, tap in 2 new oil seals.

   SST 09350-30020 (09350-07110) 

   Fig 47: Identifying Oil Seals

   Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
2. Coat the oil seal lips with MP grease.

1. Install a new spacer onto the manual valve lever.
Fig 48: Identifying Spacer Onto Manual Valve Lever
Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
2. Install the manual valve lever shaft onto the transmission case through the manual valve lever.
3. Using a hammer, tap in a new spring pin.
   Fig 49: Identifying Spring Pin

   Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
4. Align the manual valve lever indentation with the spacer hole, and stake them together with a punch and hammer.
Fig 50: Identifying Manual Valve Lever Indentation With Spacer Hole
Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
5. Make sure the shaft rotates smoothly.

1. Install the E-ring onto the shaft.
2. Install the parking lock pawl, shaft and spring.
   Fig 51: Identifying Parking Lock Pawl, Shaft And Spring

   Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002

1. Connect the parking lock rod to the manual valve lever.
   Fig 52: Identifying Parking Lock Rod Sub-Assembly

   Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002

1. Place the parking lock pawl bracket onto the transmission case and tighten the 3 bolts.

   Torque: 7.4 N*m (75 kgf*cm, 65 in.*lbf) 

   Fig 53: Identifying Parking Lock Pawl Bracket

   Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
2. Shift the manual valve lever to the P position, and confirm that the planetary ring gear is correctly locked up by the lock pawl.
   Fig 54: Identifying Manual Valve Lever To P Position

   Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002

1. Coat a new O-ring with ATF, and install it onto the piston.
   Fig 55: Identifying C-1 Accumulator Valve

   Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
2. Install the 2 springs and accumulator valve into the hole.

   Accumulator spring 

   ACCUMULATOR SPRING SPECIFICATION
   
   

   Spring	Free length Outer diameter	Color
   C-1 Inner	30.40 mm (1.197 in.) 11.40 mm (0.449 in.)	Pink
   C-1 Outer	48.76 mm (1.920 in.) 16.60 mm (0.654 in.)	Light green

   Fig 56: Identifying Springs And Accumulator Valve

   Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002

1. Coat a new O-ring with ATF, and install it into the piston.
   Fig 57: Identifying C-3 Accumulator Piston

   Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
2. Install the 2 springs and accumulator piston into the hole.

   Accumulator spring 

   ACCUMULATOR SPRING SPECIFICATION
   
   

   Spring	Free length Outer diameter	Color
   C-3 Inner	44.0 mm (1.732 in.) 14.0 mm (0.551 in.)	Yellow
   C-3 Outer	73.35 mm (2.888 in.) 19.90 mm (0.784 in.)	Red

   Fig 58: Identifying Springs And Accumulator Piston

   Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002

1. Coat 2 new O-rings with ATF, and install them onto the piston.
   Fig 59: Identifying B-3 Accumulator Piston

   Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
2. Install the spring and accumulator piston into the hole.

   Accumulator spring 

   ACCUMULATOR SPRING SPECIFICATION
   
   

   Spring	Free length Outer diameter	Color
   B-3	70.5 mm (2.776 in.) 19.7 mm (0.776 in.)	Purple

   Fig 60: Identifying Spring And Accumulator Piston

   Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002

1. Coat 2 new O-rings with ATF, and install them onto the piston.
   Fig 61: Identifying C-2 Accumulator Piston

   Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
2. Install the spring and accumulator piston into the hole.

   Accumulator spring 

   ACCUMULATOR SPRING SPECIFICATION
   
   

   Spring	Free length Outer diameter	Color
   C-2	62.0 mm (2.441 in.) 15.9 mm (0.626 in.)	White

   Fig 62: Identifying Spring And Accumulator Piston

   Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002

1. Install the check ball body and spring.
   Fig 63: Identifying Check Ball Body And Spring

   Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002

1. Install the 3 brake drum gaskets.
   Fig 64: Identifying Brake Drum Gasket

   Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002

1. Install the 3 transaxle case gaskets.
   Fig 65: Identifying Transaxle Case Gaskets

   Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002

1. Align the groove of the manual valve with the pin of the lever.
   Fig 66: Identifying Groove Of Manual Valve With Pin Of Lever

   Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
2. Install the 19 bolts.

   Torque: 11 N*m (112 kgf*cm, 8 ft.*lbf) 

   HINT:

   Each bolt length is as indicated below.

   Bolt length: 

   25 mm (0.98 in.) for bolt A 

   36 mm (1.42 in.) for bolt B 

   Fig 67: Identifying Bolt

   Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002

1. Install a new O-ring onto the transmission wire.
2. Install the transmission wire harness.
3. Install the bolt.

   Torque: 5.4 N*m (55 kgf*cm, 48 in.*lbf) 

4. Connect the solenoid connector.
   Fig 68: Identifying Solenoid Connector Bolts

   Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
5. Connect the 7 solenoid connectors.
6. Install the ATF temperature sensor.
7. Install the 2 clamps and the 2 bolts.

   Torque: 

   10 N*m (100 kgf*cm, 7 ft.*lbf) for bolt A 

   11 N*m (112 kgf*cm, 8 ft.*lbf) for bolt B 

   HINT:

   Each bolt length is indicated below.

   Bolt length: 

   12 mm (0.47 in.) for bolt A 

   36 mm (1.42 in.) for bolt B 

   Fig 69: Identifying Clamps With Bolts

   Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002

1. Coat a new O-ring with ATF, and install them onto the valve body oil strainer assembly.
2. Install the oil strainer with the 4 bolts.

   Torque: 10 N*m (100 kgf*cm, 7 ft.*lbf) 

   Fig 70: Identifying Valve Body Oil Strainer Assembly Bolts

   Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002

1. Install the 4 transmission oil cleaner magnets.

Fig 71: Identifying Transmission Oil Cleaner Magnets

Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002

1. Install a new gasket onto the oil pan.
2. Install the 20 bolts.

   Torque: 4.4 N*m (45 kgf*cm, 39 in.*lbf) 

3. Install the drain plug.

   Torque: 28 N*m (285 kgf*cm, 21 ft.*lbf) 

1. Using SST and a hammer, tap in a new oil seal.

   SST 09226-10010 

   Fig 72: Identifying Oil Seal

   Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002

1. Apply seal packing or equivalent to the 8 bolts.

   Seal packing: 

   Toyota Genuine Seal Packing 1281, Three Bond 1281 or Equivalent 

   Fig 73: Identifying Gasket

   Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
2. Install the transmission case adapter sub-assembly with the 8 bolts.

   Torque: 34 N*m (345 kgf*cm, 25 ft.*lbf) 

   HINT:

   Each bolt length is indicated below.

   Bolt length: 

   50 mm (1.969 in.) for bolt A 

   40 mm (1.575 in.) for bolt B 

   Fig 74: Identifying Transmission Case Adapter Sub-Assembly With Bolts

   Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002

1. Clean the threads of the bolts and case with white gasoline.
2. Install the transmission housing with the 10 bolts.

   Torque: 

   34 N*m (345 kgf*cm, 25 ft.*lbf) for bolt A 

   57 N*m (581 kgf*cm, 42 ft.*lbf) for bolt B 

   34 N*m (345 kgf*cm, 25 ft.*lbf) for bolt C 

   HINT:

   Each bolt length is indicated below.

   Bolt length: 

   Bolt A: 14 mm 

   Bolt B: 17 mm 

   Bolt C: 14 mm 

   Fig 75: Identifying Transmission Housing Bolts

   Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002

1. Install a new O-ring onto the breather tube.
2. Install the breather tube with the 3 bolts.

   Torque: 5.4 N*m (55 kgf*cm, 48 in.*lbf) 

   Fig 76: Identifying Breather Tube With Bolts

   Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002

1. Coat 2 new O-rings with AFT, and install one onto each transmission revolution sensor.
2. Install the 2 transmission revolution sensors.
3. Install the 2 bolts.

   Torque: 5.4 N*m (55 kgf*cm, 48 in.*lbf) 

   Fig 77: Identifying Transmission Revolution Sensors Bolts

   Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002

1. Coat 2 new O-rings with ATF, and install one onto each oil cooler tube union.
2. Install the 2 oil cooler tube unions.

   Torque: 29 N*m (296 kgf*cm, 21 ft.*lbf) 

   Fig 78: Identifying Oil Cooler Tube Unions

   Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002

1. Install the park/neutral position switch onto the manual valve lever shaft, and temporarily install the adjusting bolt.
2. Install a new lock washer and tighten the nut.

   Torque: 6.9 N*m (70 kgf*cm, 61 in.*lbf) 

   Fig 79: Identifying Nut, Lock Washer And Bolt

   Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
3. Push the control shaft rearward as much as possible.
4. Return the control shaft lever 2 notches to the N position.
   Fig 80: Identifying Control Shaft Lever

   Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
5. Align the neutral basic line with the switch groove as shown in the illustration, and tighten the adjusting bolt.

   Torque: 13 N*m (129 kgf*cm, 9.4 ft.*lbf) 

   Fig 81: Identifying Neutral Basic Line With Switch Groove

   Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
6. Using a screwdriver, bend the tabs of the lock washer.

   HINT:

   Bend at least 2 of the lock washer tabs.

   Fig 82: Identifying Tabs Of Lock Washer

   Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002

1. Install the control shaft lever LH with the washer and nut.

   Torque: 16 N*m (163 kgf*cm, 12 ft.*lbf) 

   Fig 83: Identifying Transmission Control Shaft Lever Nut LH

   Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002