LEMON Manuals: Even more car manuals for everyone
Home >> Toyota >> 2009 >> FJ Cruiser 4WD, Automatic >> Repair and Diagnosis >> Body & Frame >> Windows >> Windshield/Window Glass >> Rear Side Window Glass >> Installation

Rear Side Window Glass: Installation

  1. CLEAN REAR DOOR GLASS 
    1. Clean the outer circumference of the glass with a non-residue solvent.
      NOTE:
      • Do not touch the glass surface after cleaning it.
      • Even if using a new glass, clean the glass with a non-residue solvent.
        Fig 1: Identifying Outer Circumference Of Glass
        G05114380Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
  2. CLEAN VEHICLE BODY 
    1. Clean and shape the contact surface of the vehicle body.
      1. Using a knife, cut away any rough adhesive on the contact surface of the vehicle body to ensure the appropriate surface shape.
        NOTE: Do not damage the vehicle body.

        HINT:

        Leave as much adhesive on the vehicle body as possible.

        Fig 2: Identifying Adhesive On Vehicle Body Contact Surface
        G04833862Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
      2. Clean the contact surface of the vehicle body with a shop rag or piece of cloth saturated with cleaner.

        HINT:

        Clean the vehicle body even if all the adhesive has been removed.

  3. INSTALL REAR DOOR GLASS 
    1. Using a brush, apply Primer M to the exposed part of the vehicle body.
      NOTE:
      • Allow the primer to dry for 3 minutes or more.
      • Do not apply Primer M to the adhesive.
      • Throw away any leftover Primer M.
      • Do not apply too much Primer M.
        Fig 3: Identifying Primer M To Exposed Part Of Vehicle Body
        G04833927Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
    2. Using a brush or sponge, apply Primer G to the edge of the rear door glass and contact surface.

      Specification 

      SPECIFICATION

      Area Measurement
      a 5.0 mm (0.197 in.)
      b 20 mm (0.787 in.)
      c 15 mm (0.591 in.)
      d 26 mm (1.024 in.)
      Fig 4: Identifying Primer G To Edge Of Rear Door Glass And Contact Surface
      G05114347Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
      NOTE:
      • Allow the primer to dry for 3 minutes or more.
      • Throw away any leftover Primer G.
      • Do not apply too much Primer G.

      HINT:

      If Primer G is applied to any areas other than those specified, wipe off the primer with a clean shop rag or piece of cloth before it dries.

    3. Apply adhesive.

      Adhesive: 

      Toyota Genuine Windshield Glass Adhesive or the equivalent 

      1. Cut the tip off the cartridge nozzle, as shown in the illustration.

        HINT:

        After cutting off the tip, use all adhesive within the time indicated in the table below.

        Usage time frame 

        TIME FRAME REFERENCE

        Temperature Usage Time Frame
        35°C (95°F) 15 minutes
        20°C (68°F) 1 hour 40 minutes
        5°C (41°F) 8 hours
        Fig 5: Cutting Tip Off Cartridge Nozzle
        G05114348Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
      2. Load the sealer gun with the cartridge.
      3. Apply adhesive to the rear door glass as shown in the illustration.

        Specification 

        SPECIFICATION

        Area Measurement
        a 8 mm (0.315 in.)
        b 12 mm (0.472 in.)
        c 13 mm (0.512 in.)
        d 14.2 mm (0.559 in.)
        e 11.6 mm (0.457 in.)
    4. Install the rear door glass onto the body.
      1. Hold the quarter window glass in place securely with protective tape or the equivalent until the adhesive hardens.
        NOTE:
        • Allow the primer coating to dry for 3 minutes or more.
        • Check that the pins are attached to the body correctly.
        • Check the clearance between the body and glass.
      2. Lightly press the front surface of the glass to ensure a close fit.
      3. Using a scraper, remove any excessive or protruding adhesive.

        HINT:

        Apply adhesive to the rear door glass rim.

        NOTE: Do not drive the vehicle within the time indicated in the table below.

        Minimum time 

        MINIMUM TIME REFERENCE

        Temperature Minimum time prior to driving vehicle
        35°C (95°F) 1 hour 30 minutes
        20°C (68°F) 5 hours
        5°C (41°F) 24 hours
        Fig 6: Removing Excessive Or Protruding Adhesive
        G04833955Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
  4. CHECK FOR LEAKAGE AND REPAIR 
    1. Conduct a leak test by applying water to the adhesive portions after the adhesive has completely hardened.
    2. Seal any leakage with auto glass sealer.
  5. INSTALL ACCESS DOOR GLASS OUTER WEATHERSTRIP 

    HINT:

    Use the same procedure as for the RH side (see INSTALLATION ).

  6. INSTALL REAR DOOR OPENING TRIM 

    HINT:

    Use the same procedure as for the RH side (see REASSEMBLY ).

  7. INSTALL CENTER PILLAR UPPER GARNISH 

    HINT:

    Use the same procedure as for the RH side (see REASSEMBLY ).

  8. INSTALL REAR DOOR TRIM BOARD SUB-ASSEMBLY 

    HINT:

    Use the same procedure as for the RH side (see REASSEMBLY ).

  9. INSTALL NO. 1 CUP HOLDER 

    HINT:

    Use the same procedure as for the RH side (see REASSEMBLY ).

  10. INSTALL REAR DOOR INSIDE HANDLE SUB-ASSEMBLY 

    HINT:

    Use the same procedure as for the RH side (see REASSEMBLY ).

  11. INSTALL LAP BELT OUTER ANCHOR COVER 

    HINT:

    Use the same procedure as for the RH side (see REASSEMBLY ).

  12. INSTALL ACCESS PANEL REAR WEATHERSTRIP 

    HINT:

    Use the same procedure as for the RH side (see REASSEMBLY ).

scientia non olet · About LEMON Manuals