Specifications Index
TUNDRA SPECIFICATIONS INDEX
| System | Specification/Procedure | ||
|---|---|---|---|
| Air Conditioning | |||
| Service | SERVICE DATA | ||
| Torque | TORQUE SPECIFICATIONS | ||
| Axle Nut/Hub Nut | |||
| 2WD | 382 N.m (3,895 kgf.cm, 282 ft. lbf) | ||
| 4WD | 338 N.m (3,446 kgf.cm, 249 ft. lbf) | ||
| Battery | NA | ||
| Brakes | |||
| Bleeding Sequence | REPLACEMENT | ||
| Disc Brakes | SERVICE DATA | ||
| Drum Brakes | SERVICE DATA | ||
| Torque | TORQUE SPECIFICATIONS | ||
| Charging | |||
| 1GR-FE | |||
| Generator | SERVICE DATA | ||
| Torque | TORQUE SPECIFICATIONS | ||
| 2UZ-FE | |||
| Generator | SERVICE DATA | ||
| Torque | TORQUE SPECIFICATIONS | ||
| 3UR-FE | |||
| Generator | SERVICE DATA | ||
| Torque | TORQUE SPECIFICATIONS | ||
| Drive Belts | |||
| 1GR-FE | |||
| Adjustment | ON-VEHICLE INSPECTION | ||
| Belt Routing | DRIVE BELT | ||
| 2UZ-FE | |||
| Adjustment | ON-VEHICLE INSPECTION | ||
| Belt Routing | DRIVE BELT | ||
| 3UR-FE | |||
| Adjustment | ON-VEHICLE INSPECTION | ||
| Belt Routing | DRIVE BELT | ||
| Engine Cooling | |||
| 1GR-FE | |||
| General Service Specifications | SERVICE DATA | ||
| Radiator Cap Pressure | Standard Value, 93 to 122 kPa (0.95 to 1.25 kgf/cm2
, 13.5 to 18 psi) Minimum Standard Value, 79 kPa (0.8 kgf/cm2 , 11.4 psi) |
||
| Thermostat R & I | THERMOSTAT | ||
| Water Pump R & I | WATER PUMP | ||
| 2UZ-FE | |||
| General Service Specifications | SERVICE DATA | ||
| Radiator Cap Pressure | Standard Value, 93.3 to 122.7 kPa (0.95 to 1.25 kgf/cm2
, 13.5 to 17.8 psi) Minimum Standard Value, 78.5 kPa (0.8 kgf/cm2 , 11.4 psi) |
||
| Thermostat R & I | THERMOSTAT | ||
| Water Pump R & I | WATER PUMP | ||
| 3UR-FE | |||
| General Service Specifications | SERVICE DATA | ||
| Radiator Cap Pressure | Standard Value, 93 to 123 kPa (1.0 to 1.3 kgf/cm2
, 13.5 to 17.8 psi) Minimum Standard Value, 78.5 kPa (0.8 kgf/cm2 , 11.4 psi) |
||
| Thermostat R & I | THERMOSTAT | ||
| Water Pump R & I | WATER PUMP | ||
| Engine Mechanical | |||
| 1GR-FE | |||
| Compression | SERVICE DATA | ||
| Oil Pressure | @ idling, 29 kPa (0.3 kgf/cm2
, 4.3 psi) or more @ 3,000 rpm, 294 to 588 kPa (3.0 to 6.0 kgf/cm2 , 43 to 85 psi) |
||
| Overhaul | SERVICE DATA | ||
| Torque | TORQUE SPECIFICATIONS | ||
| 2UZ-FE | |||
| Compression | SERVICE DATA | ||
| Oil Pressure | @ idle, 29 kPa (0.3 kgf/cm2
, 4.2 psi) or more @ 3,000 rpm, 294 to 588 kPa (3.0 to 6.0 kgf/cm2 , 43 to 85 psi) |
||
| Overhaul | SERVICE DATA | ||
| Torque | TORQUE SPECIFICATIONS | ||
| 3UR-FE | |||
| Compression | SERVICE DATA | ||
| Oil Pressure | @ idle, 70 kPa (0.7 kgf/cm2
, 10.1 psi) or more @ 2,500 rpm, 220 kPa ( 2.2 kgf/cm2 , 31.9 psi) |
||
| Overhaul | SERVICE DATA | ||
| Torque | TORQUE SPECIFICATIONS | ||
| Fluid Specifications | See FLUIDS under MAINTENANCE tab. | ||
| Flywheel/Flex Plate (Drive Plate) Torque | |||
| 1GR-FE | 83 N.m (46 kgf.cm, 61 ft. lbf) | ||
| 2UZ-FE | Step1: 30 N.m (306 kgf.cm, 22 ft. lbf) Step2: Turn 90° |
||
| 3UR-FE | Step1: 30 N.m (301 kgf.cm, 22 ft. lbf) Step2: Turn 90° |
||
| Fuel System | |||
| 1GR-FE | |||
| Pressure Specification | @ idle;281 to 287 kPa (2.87 to 2.93 kgf/cm2 , 40.8 to 41.7 psi) | ||
| Fuel Pressure Test Procedure | ON-VEHICLE INSPECTION | ||
| Fuel Filter Location | COMPONENTS | ||
| 2UZ-FE | |||
| Pressure Specification | @idle;265 to 304 kPa (2.7 to 3.1 kgf/cm2 , 38 to 44 psi) | ||
| Fuel Pressure Test Procedure | ON-VEHICLE INSPECTION | ||
| Fuel Filter Location | COMPONENTS | ||
| 3UR-FE | |||
| Pressure Specification | @idle;281 to 287 kPa (2.87 to 2.97 kgf/cm2 , 38 to 44 psi) | ||
| Fuel Pressure Test Procedure | ON-VEHICLE INSPECTION | ||
| Fuel Filter Location | COMPONENTS | ||
| Ignition | |||
| Firing Order & Cylinder Identification | FIRING ORDER & CYLINDER IDENTIFICATION | ||
| Spark Plug | |||
| 1GR-FE | |||
| Type | DENSO K20HR-U11 | ||
| Gap | Standard electrode gap 1.0 to 1.1 mm (0.0394 to 0.0433 in.) |
||
| Torque | 20 N.m (204 kgf.cm, 15 ft. lbf) | ||
| 2UZ-FE | |||
| Type | DENSO SK20R-11 NGK IFR6A11 |
||
| Gap | Standard electrode gap 1.0 to 1.1 mm (0.0394 to 0.0433 in.) Maximum electrode gap 1.3 mm (0.0512 in.) |
||
| Torque | 18 N.m (178 kgf.cm, 13 ft. lbf) | ||
| 3UR-FE | |||
| Type | DENSO SK20HR-11 | ||
| Gap | Standard electrode gap 1.0 to 1.1 mm (0.0394 to 0.0433 in.) Maximum electrode gap 1.3 mm (0.0512 in.) |
||
| Torque | 18 N.m (178 kgf.cm, 13 ft. lbf) | ||
| Starting | |||
| 1GR-FE | |||
| Starter | SERVICE DATA | ||
| Torque | TORQUE SPECIFICATIONS | ||
| 2UZ-FE | |||
| Starter | SERVICE DATA | ||
| Torque | TORQUE SPECIFICATIONS | ||
| 3UR-FE | |||
| Starter | SERVICE DATA | ||
| Torque | TORQUE SPECIFICATIONS | ||
| Wheel Alignment | |||
| Front & Rear | |||
| Adjustment Specifications | SERVICE DATA | ||
| Torque | TORQUE SPECIFICATIONS | ||
| Wheel & Tire | |||
| Wheel Lug Nut Torque | Aluminum Wheel, 131 N.m (1336 kgf.cm, 97 ft.Ibf) Steel Wheel, 209 N.m (2131 kgf.cm, 154 ft.Ibf |
||