LEMON Manuals: Even more car manuals for everyone
Home >> Toyota >> 2008 >> Land Cruiser >> Repair and Diagnosis >> Transmission >> Automatic Trans >> Automatic Transmission >> Valve Body Assembly >> Inspection

Valve Body Assembly: Inspection

  1. INSPECT SHIFT SOLENOID VALVE SL1 
    1. Measure the resistance according to the value(s) in the table below.

      Standard Resistance 

      RESISTANCE SPECIFICATION

      Tester Connection Condition Specified Condition
      1 - 2 20°C (68°F) 5.0 to 5.6 Ω
    2. Apply 12V battery voltage to the shift solenoid valve and check that the valve moves and makes an operating noise.

      OK 

      MEASUREMENT AND SPECIFIED CONDITION

      Measurement Condition Specified Condition
      Battery positive (+) with a 21 W bulb → Terminal 1
      Battery negative (-) → Terminal 2      		 Valve moves and makes an operating noise

      If the result is not as specified, replace the solenoid valve.

      Fig 1: Inspecting Shift Solenoid Valve SL1
      G05629112Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
  2. INSPECT SHIFT SOLENOID VALVE S1 
    1. Measure the resistance according to the value(s) in the table below.

      Standard Resistance 

      RESISTANCE SPECIFICATION

      Tester Connection Condition Specified Condition
      Shift solenoid valve S1 connector terminal - Shift solenoid valve S1 body 20°C (68°F) 11 to 15 Ω
    2. Apply 12V battery voltage to the shift solenoid valve and check that the valve moves and makes an operating noise.

      OK 

      MEASUREMENT AND SPECIFIED CONDITION

      Measurement Condition Specified Condition
      Battery positive (+) → Shift solenoid valve S1 connector
      Battery negative (-) → Shift solenoid valve S1 body      		 Valve moves and makes an operating noise
      Fig 2: Inspecting Shift Solenoid Valve S1
      G05629113Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002

      If the result is not as specified, replace the solenoid valve.

  3. INSPECT SHIFT SOLENOID VALVE S2 
    1. Measure the resistance according to the value(s) in the table below.

      Standard Resistance 

      RESISTANCE SPECIFICATION

      Tester Connection Condition Specified Condition
      Shift solenoid valve S2 connector terminal - Shift solenoid valve S2 body 20°C (68°F) 11 to 15 Ω
    2. Apply 12 V battery voltage to the shift solenoid valve and check that the valve moves and makes an operating noise.

      OK 

      MEASUREMENT AND SPECIFIED CONDITION

      Measurement Condition Specified Condition
      Battery positive (+) → Shift solenoid valve S2 connector
      Battery negative (-) → Shift solenoid valve S2 body      		 Valve moves and makes an operating noise
      Fig 3: Inspecting Shift Solenoid Valve S2
      G05629114Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002

      If the result is not as specified, replace the solenoid valve.

  4. INSPECT SHIFT SOLENOID VALVE S3 
    1. Measure the resistance according to the value(s) in the table below.

      Standard Resistance 

      RESISTANCE SPECIFICATION

      Tester Connection Condition Specified Condition
      Shift solenoid valve S3 connector terminal - Shift solenoid valve S3 body 20°C (68°F) 11 to 15 Ω
    2. Apply 12V battery voltage to the shift solenoid valve and check that the valve moves and makes an operating noise.

      OK 

      MEASUREMENT AND SPECIFIED CONDITION

      Measurement Condition Specified Condition
      Battery positive (+) → Shift solenoid valve S3 connector
      Battery negative (-) → Shift solenoid valve S3 body      		 Valve moves and makes an operating noise
      Fig 4: Inspecting Shift Solenoid Valve S3
      G05629115Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002

      If the result is not as specified, replace the solenoid valve.

  5. INSPECT SHIFT SOLENOID VALVE S4 
    1. Measure the resistance according to the value(s) in the table below.

      Standard Resistance 

      RESISTANCE SPECIFICATION

      Tester Connection Condition Specified Condition
      Shift solenoid valve S4 connector terminal - Shift solenoid valve S4 body 20°C (68°F) 11 to 15 Ω
    2. Apply 12 V battery voltage to the shift solenoid valve and check that the valve moves and makes an operating noise.

      OK 

      MEASUREMENT AND SPECIFIED CONDITION

      Measurement Condition Specified Condition
      Battery positive (+) → Shift solenoid valve S4 connector
      Battery negative (-) → Shift solenoid valve S4 body      		 Valve moves and makes an operating noise
      Fig 5: Inspecting Shift Solenoid Valve S4
      G05629116Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002

      If the result is not as specified, replace the solenoid valve.

  6. INSPECT SHIFT SOLENOID VALVE SL2 
    1. Measure the resistance according to the value(s) in the table below.

      Standard Resistance 

      RESISTANCE SPECIFICATION

      Tester Connection Condition Specified Condition
      1 - 2 20°C (68°F) 5.0 to 5.6 Ω
    2. Apply 12V battery voltage to the shift solenoid valve and check that the valve moves and makes an operating noise.

      OK 

      MEASUREMENT AND SPECIFIED CONDITION

      Measurement Condition Specified Condition
      Battery positive (+) with a 21 W bulb → Terminal 1
      Battery negative (-) → Terminal 2      		 Valve moves and makes an operating noise

      If the result is not as specified, replace the solenoid valve.

      Fig 6: Inspecting Shift Solenoid Valve SL2
      G05629117Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
  7. INSPECT SHIFT SOLENOID VALVE SR 
    1. Measure the resistance according to the value(s) in the table below.

      Standard Resistance 

      RESISTANCE SPECIFICATION

      Tester Connection Condition Specified Condition
      Shift solenoid valve SR connector terminal - Shift solenoid valve SR body 20°C (68°F) 11 to 15 Ω
    2. Apply 12 V battery voltage to the shift solenoid valve and check that the valve moves and makes an operating noise.

      OK 

      MEASUREMENT AND SPECIFIED CONDITION

      Measurement Condition Specified Condition
      Battery positive (+) → Shift solenoid valve SR connector
      Battery negative (-) → Shift solenoid valve SR body      		 Valve moves and makes an operating noise
      Fig 7: Inspecting Shift Solenoid Valve SR
      G05629118Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002

      If the result is not as specified, replace the solenoid valve.

  8. INSPECT SHIFT SOLENOID VALVE SLT 
    1. Measure the resistance according to the value(s) in the table below.

      Standard Resistance 

      RESISTANCE SPECIFICATION

      Tester Connection Condition Specified Condition
      1 - 2 20°C (68°F) 5.0 to 5.6 Ω
    2. Apply 12 V battery voltage to the shift solenoid valve and check that the valve moves and makes an operating noise.

      OK 

      MEASUREMENT AND SPECIFIED CONDITION

      Measurement Condition Specified Condition
      Battery positive (+) with a 21 W bulb → Terminal 2
      Battery negative (-) → Terminal 1      		 Valve moves and makes an operating noise

      If the result is not as specified, replace the solenoid valve.

      Fig 8: Inspecting Shift Solenoid Valve SLT
      G05629119Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
  9. INSPECT SHIFT SOLENOID VALVE SLU 
    1. Measure the resistance according to the value(s) in the table below.

      Standard Resistance 

      RESISTANCE SPECIFICATION

      Tester Connection Condition Specified Condition
      1 - 2 20°C (68°F) 5.0 to 5.6 Ω
    2. Apply 12V battery voltage to the shift solenoid valve and check that the valve moves and makes an operating noise.

      OK 

      MEASUREMENT AND SPECIFIED CONDITION

      Measurement Condition Specified Condition
      Battery positive (+) with a 21 W bulb → Terminal 2
      Battery negative (-) → Terminal 1      		 Valve moves and makes an operating noise

      If the result is not as specified, replace the solenoid valve.

      Fig 9: Inspecting Shift Solenoid Valve SLU
      G05629120Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
scientia non olet · About LEMON Manuals