Floor Shift Assembly: Disassembly

REMOVE SHIFT LEVER KNOB SUB-ASSEMBLY
1. Releasing the lock by pressing the slick, disconnect the indicator light wire connector from the shift lever plate.
  
  Fig 1: Identifying Indicator Light Wire Connector
  Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
2. Disengage the secondary locking device.
3. Using a small screwdriver, disengage the locking lug of the terminals 2 and 4, and pull the terminals out from the rear.
4. Disconnect the wire harness from the clamps.
5. Remove the 2 screws and shift lever knob sub-assembly.
  NOTE: Pay attention not to apply unnatural load to transmission control switch wire harness.
  
  Fig 3: Identifying Shift Lever Knob Screws
  Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
REMOVE FLOOR SHIFT SHIFT LEVER KNOB COVER
1. Remove the shift lever knob cover.
  
  Fig 4: Identifying Floor Shift Shift Lever Knob Cover
  Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
REMOVE TRANSMISSION CONTROL SWITCH
1. Using a small screwdriver, remove the transmission control switch.
  HINT:
  
  Tape up the screwdriver tip before use.
  
  Fig 5: Identifying Transmission Control Switch
  Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
REMOVE SHIFT LEVER KNOB BUTTON
1. Remove the shift lever knob button and spring.
  
  Fig 6: Identifying Shift Lever Knob Button And Spring
  Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
REMOVE INDICATOR LIGHT WIRE SUB-ASSEMBLY
1. Remove the indicator light wire sub-assembly.
2. Remove the cap and bulb from the indicator light wire sub-assembly.
REMOVE SHIFT LOCK RELEASE BUTTON COVER
1. Using a screwdriver, remove the shift lock release button cover.
  HINT:
  
  Tape up the screwdriver tip before use.
  
  Fig 8: Identifying Shift Lock Release Button Cover
  Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
REMOVE UPPER POSITION INDICATOR HOUSING
1. Using a screwdriver, release the 4 claws and remove the upper position indicator housing.
  HINT:
  
  Tape up the screwdriver tip before use.
  
  Fig 9: Identifying Upper Position Indicator Housing Claws
  Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
REMOVE CONTROL POSITION INDICATOR PLATE
1. Remove the position indicator plate from the upper position indicator housing.
  
  Fig 10: Identifying Control Position Indicator Plate
  Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
REMOVE POSITION INDICATOR SLIDE COVER
1. Remove the position indicator slide cover.
  
  Fig 11: Identifying Position Indicator Slide Cover
  Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
REMOVE LOWER POSITION INDICATOR HOUSING
1. Using a screwdriver, release the 3 claws and remove the lower position indicator housing.
  HINT:
  
  Tape up the screwdriver tip before use.
  
  Fig 12: Identifying Lower Position Indicator Housing Claws
  Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
REMOVE SHIFT LOCK RELEASE BUTTON
1. Remove the shift lock release button and spring.
  
  Fig 13: Identifying Shift Lock Release Button
  Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
REMOVE SHIFT LOCK CONTROL UNIT ASSEMBLY
1. Using a screwdriver, remove the toggle lever support pin and shift lock control unit assembly.
  NOTE: Work so as not to damage the stopper position.
  
  HINT:
  
  Tape up the screwdriver tip before use.
  
  Fig 14: Identifying Toggle Lever Support Pin
  Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
REMOVE NO.1 SHIFT LEVER INSERT