Rear Coil Spring: Installation

INSTALL REAR COIL SPRING LH
1. Install the coil spring insulator lower onto the axle beam.
2. Install the coil spring insulator upper so that its gap fits onto the end of coil spring.
  
  Fig 1: Installing Rear Coil Spring LH
  Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
3. Install the coil spring onto the axle beam.
  NOTE: The paint mark of the coil spring should be towards the underside and rear side of the vehicle.
INSTALL REAR COIL SPRING RH
HINT:

The installation procedure for the RH side is the same as that for the LH side.
TEMPORARILY TIGHTEN REAR SHOCK ABSORBER LH (See INSTALLATION )

Fig 2: Identifying Rear Coil Spring RH Paint Mark
Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
TEMPORARILY TIGHTEN REAR SHOCK ABSORBER RH
HINT:

The installation procedure for the RH side is the same as that for the LH side.
INSTALL REAR SHOCK ABSORBER CAP LH
INSTALL REAR SHOCK ABSORBER CAP RH
INSTALL REAR ABSORBER CAP (for Hatchback)
INSTALL REAR LH FLEXIBLE HOSE
1. Connect the flexible hose onto the axle beam with a new clip.
2. Using SST, install the brake tube.
  SST 09023-00101
  
  Torque: for use without SST
  
  15 N.m (155 kgf*cm, 11 ft.*lbf)
  
  for use with SST
  
  14 N.m (143 kgf*cm, 10 ft.*lbf)
  
  Fig 3: Identifying SST
  Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
  
  HINT:
  - Use a torque wrench with a fulcrum length of 300 mm (11.81 in.).
  - This torque value is effective when SST is parallel to a torque wrench.
INSTALL REAR RH FLEXIBLE HOSE
HINT:

The installation procedure for the RH side is the same as that for the LH side.
INSTALL SKID CONTROL SENSOR WIRE (w/ ABS)
1. Install the skid control sensor wire onto the axle beam with the nut.
  Torque: 6.0 N.m (61 kgf*cm, 53 in.*lbf)
  
  Fig 4: Locating Skid Control Sensor Wire Nut
  Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
2. Connect the skid control sensor wire connector.
INSTALL REAR WHEEL
Torque: 103 N.m (1,050 kgf*cm, 76 ft.*lbf)
STABILIZE SUSPENSION
1. Lower the vehicle from the jack.
2. Bounce the vehicle up and down several times to stabilize the suspension.
FULLY TIGHTEN REAR AXLE BEAM (See INSTALLATION )
FULLY TIGHTEN REAR SHOCK ABSORBER LH (See INSTALLATION )

Fig 5: Identifying Skid Control Sensor Wire Connector
Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
FULLY TIGHTEN REAR SHOCK ABSORBER RH
HINT:

The installation procedure for the RH side is the same as that for the LH side.
INSTALL REAR SEATBACK ASSEMBLY (for Sedan Fixed Seat Type) (See INSTALLATION )
INSTALL REAR SEAT CUSHION COVER PAD SUB-ASSEMBLY (for Sedan Fixed Seat Type) (See INSTALLATION )
CONNECT CABLE TO NEGATIVE BATTERY TERMINAL
Torque: 5.4 N.m (55 kgf*cm, 48 in.*lbf)
FILL RESERVOIR WITH BRAKE FLUID (See BLEEDING )
BLEED MASTER CYLINDER (See BLEEDING )
BLEED BRAKE LINE (See BLEEDING )
CHECK FLUID LEVEL IN RESERVOIR (See BLEEDING )
CHECK FOR BRAKE FLUID LEAKAGE
INSPECT REAR WHEEL ALIGNMENT
(See REAR WHEEL ALIGNMENT
CHECK ABS SENSOR SIGNAL (w/ABS) (See TEST MODE PROCEDURE )