Customize Parameters

HINT:

The following items can be customized.

NOTE:

After confirming whether the items of the customer's request are applicable or not for the customized items, perform the customize operation.
Be sure to record the current value before customizing.
In case of performing the troubleshooting, pay attention as there is a possibility that the function is set to OFF by customizing. (Example: In case of the symptom in which "The wireless operation does not function" is displayed, check that the wireless operation is not set to OFF by customizing, then perform the troubleshooting.)

AIR CONDITIONING SYSTEM

AIR CONDITIONER

AIR CONDITIONER SPECIFICATION

DISPLAY (ITEM)	DEFAULT	CONTENTS	SETTING
SET TEMP SHIFT (Shift set temperature)	NORMAL	To control with the shifted temperature against the display temperature.	+2C / +1C / NORMAL -1C / -2C
AIR INLET MODE (Air inlet mode)	AUTO	In case of turning the A/C ON when you desire to make the compartment cool down quickly, this is the function to change the mode automatically to RECIRCULATED mode.	MANUAL/AUTO
COMPRESSOR MODE (Compressor mode)	AUTO	Function to turn the A/C ON automatically by pressing the AUTO button when the blower is ON and the A/C is OFF.	MANUAL/AUTO
COMPRS/DEF OPER (Compressor/DEF operation mode)	LINK	Function to turn the A/C ON automatically linking with the FRONT DEF button when the A/C is OFF.	NORMAL/LINK
AUTO BLOW UP (Foot/DEF automatic blow up function)	ON	Function to switch the blower level automatically when the defroster is ON.	OFF / ON
AMBINT TMP SFT (Ambient temperature Shift)	NORMAL	To control with the shifted ambient temperature against the display ambient temperature.	+3C / +2C / +1C NORMAL / -1C / -2C / -3C

THEFT DETERRENT SYSTEM

THEFT DETERRENT SYSTEM REFERENCE CHART

DISPLAY (ITEM)	DEFAULT	CONTENTS	SETTING
PASSIVE MODE (Passive Arming Mode)	OFF	PASSIVE MODE is a function that switches theft deterrent system from arming preparation state to armed state 30 seconds after key is removed from ignition key cylinder and driver side door is closed, even if doors are not locked by wireless or door key lock operation In PASSIVE MODE, if you do not perform following operations within 14 seconds after door is opened during armed state, theft deterrent system will judge that condition as a theft and switch to alarm sounding state Unlock any door by wireless operation Reconnect battery Insert key into ignition key cylinder and turn ignition switch from OFF to ON Unlock any door by key operation	ON/OFF
WARNING (HORN) (Warning (horn))	ON	Function that makes vehicle horn and theft deterrent horn able to be used as a warning device	ON/OFF
ENTRY DELAY (Entry delay time)	14 s	Function that changes entry delay time (time before warning starts) for PASSIVE MODE	0 s/14 s/30 s

LIGHTING SYSTEM

ILLUMINATED ENTRY

LIGHTING SYSTEM REFERENCE CHART

DISPLAY (ITEM)	DEFAULT	CONTENTS	SETTING
I/L ON / UNLOCK (Interior light ON w/ door key unlock)	ON	Function to light up the interior light, ignition light and step light when unlocking with the door key cylinder. : Interior light comes on when the interior light switch is at the DOOR position.	ON / OFF
LIGHTING TIME (Lighting Time)	15 s	To change the lighting time after closing the door. (It will quickly fade out in case of turning the ignition ON.)	7.5 s/15 s/30 s

LIGHT CONTROL

LIGHT CONTROL REFERENCE CHART

DISPLAY (ITEM)	DEFAULT	CONTENTS	SETTING
SENSITIVITY (Turn ON luminous intensity)	NORMAL	To adjust the sensitivity of the lighting illumination. Refer to the .	DARK2 / DARK1 / NORMAL / LIGHT1 / LIGHT2
LIGHT CTRL TYPE (Control Type)	CURRENT	To change the control logic when the light control switch is in the AUTO position. Refer to the .	CURRENT/OLD

HINT:

Sensitivity adjustment can hardly be confirmed. Please check by customer's actual driving.

Illustration *1

VEHICLE LIGHT SPECIFICATION

Lighting brightness	DARK ↔ BRIGHT
Setting	DARK2 ↔ DARK1 ↔ NORMAL ↔ LIGHT1 ↔ LIGHT2

Illustration *2

VEHICLE LIGHT SPECIFICATION

Brightness of the surrounding when fighting

Lighting delay

Delay of turning light off

⁽²⁾

OLD

Old logic

6 sec.

3 sec.

CURRENT

New logic ⁽¹⁾ ('97/8-)

15 sec.

⁽¹⁾	The new one has the logic to light up two times brighter than the old logic.

⁽²⁾	Delay time until the headlight is turned on when it suddenly gets dark.

POWER DOOR LOCK CONTROL SYSTEM

Body ECU

ECU BODY REFERENCE CHART

Display (Item)	Default	Contents	Setting
AUTO LOCK DELAY	30s	Function that selects AUTO LOCK time (30 sec. or 60 sec.)	30s/60s
UNLK/KEY TWICE (Unlock w/ 2 times D key operation)	ON	Function that unlocks only driver side door when driver side door key cylinder is turned to unlock once and unlocks all the doors when it is turned to unlock twice In OFF setting, turning it once unlocks all doors	ON/OFF

WIRELESS DOOR LOCK CONTROL SYSTEM

ECU BODY REFERENCE CHART

Item (Display)	Default	Function	Setting
OPEN DOOR WARN (Open door warning)	ON	If any door is not completely closed and LOCK is pressed, this function sounds buzzer for 10 seconds.	ON / OFF
WIRELESS OPER (Wireless door lock control function)	ON	This function turns the wireless door lock function on or off.	ON/OFF
ALARM FUNCTION (Panic function)	ON	This function operates the theft deterrent system when PANIC is pressed and held for 0.8 seconds.	ON/OFF
UNLOCK/2OPER (Wireless unlock operated twice)	ON	This function unlocks the driver side door when UNLOCK is pressed once, and unlocks all doors when pressed twice. If setting is OFF, pressing UNLOCK once makes all doors unlock.	ON / OFF
AUTO LOCK DELAY (Auto lock time)	30 s	This function regulates the interval between unlocking and automatic relocking of the doors.	30 s / 60 s
LNT/LGT ON/UNLK (Room light illuminate when wireless unlock)	ON	When UNLOCK is pressed, this function illuminates the interior light.	ON / OFF

METER / GAUGE SYSTEM

Parameter

METER

METER SPECIFICATION

Display (Item)	Default	Contents	Setting
KEY REMND SOUND	NORMAL	Function to change cycle of key remind warning buzzer.	600 / 900 / 1,200 ms

Buzzer ON/OFF Setting

The buzzer ON/OFF setting, which is a setting of the buzzer function of the combination meter, can disable the driver side seat belt buzzer and front passenger side seat belt buzzer.

NOTE: Basically, these buzzers should be set on for safe driving. Perform the procedures only if it is necessary to set the buzzer off.

Fig 1: Display Seat Belt Buzzer

PROCEDURE

SEAT BELT PROCEDURE CHART

Steps	Driver Side Seat Belt Buzzer	Front Passenger Side Seat Belt Buzzer
1	Turn the ignition switch to the ON position.	Turn the ignition switch to the ON position.
2	Press the ODO/TRIP switch until the odometer displays "ODO".	Press the ODO/TRIP switch until the odometer displays "ODO".
3	Turn the ignition switch off.	Turn the ignition switch off.
4	Turn the ignition switch to the ON position.	Turn the ignition switch to the ON position.
5	Press the ODO/TRIP switch immediately (within 6 seconds) and hold it down for 10 seconds or more.	Sit in the front passenger seat. Press the ODO/TRIP switch immediately (within 6 seconds) and hold it down for 10 seconds or more.
6	Continue holding down the ODO/TRIP switch and fasten the driver side seat belt.	Continue holding down the ODO/TRIP switch, fasten and release the passenger side seat belt.
7	Check that the odometer displays either "SEAT BELT BUZZER ON" or "SEAT BELT BUZZER OFF".	Check that the odometer displays either "SEAT BELT BUZZER ON" or "SEAT BELT BUZZER OFF".
8	Press the ODO/TRIP switch to change the display to "SEAT BELT BUZZER OFF".	Press the ODO/TRIP switch to change the display to "SEAT BELT BUZZER OFF".
9	Turn the ignition switch off.	Turn the ignition switch off.
10	Turn the ignition switch to the ON position.	Turn the ignition switch to the ON position.
11	Check that no buzzer sounds.	Check that no buzzer sounds.

HINT:

"SEAT BELT BUZZER OFF" indicates that the buzzer is OFF. "SEAT BELT BUZZER ON" indicates that the buzzer is ON. The buzzer ON/OFF setting will be finished (the odometer will display "ODO") if the ODO/TRIP switch is not operated for 10 seconds or more. In this case, perform step 11 to check that the buzzer ON/OFF setting is complete. If it is not complete, start from step 1 again.

NOTE: When either the battery cable or the combination meter connector is disconnected, these buzzers are set on.

TIME ZONE SETTING (w/ Navigation System)

Fig 2: Display Time Zone Setting Screen
Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002

SLIDING ROOF SYSTEM

Sliding roof ECU

ECU SLIDING ROOF SYSTEM CHART

Display (Item)	Default	Contents	Setting
OPEN/DOOR KEY (Door key related OPEN)	ON	Function to manually open sliding roof linked with power window if holding driver side door key for 1.5 seconds or more to unlock position when ignition switch is off	ON/OFF
CLOSE/DOOR KEY (Door key related CLOSE)	ON	Function to manually close sliding roof linked with power window if holding driver side door key for 1.5 seconds or more to lock position when ignition switch is off	ON/OFF
OPEN/WIRELESS (Wireless key related OPEN)	ON	Function to manually open sliding roof linked with power window if pressing transmitter UNLOCK switch for 1.5 seconds or more when ignition switch is off	ON/OFF
DOOR KEY OPER (Door key related operation)	SLIDE	Function to select tilt up or slide open of manual sliding roof operation linked with power window Activate by holding driver side door key for 1.5 seconds or more to unlock position when ignition switch is off	TILT/SLIDE
WIRELESS OPER (Wireless key related operation)	SLIDE	Function to select tilt up or slide open of manual sliding roof operation linked with power window Activate by pressing on transmitter UNLOCK switch for 1.5 seconds or more when ignition switch is off	TILT/SLIDE