Inspection Procedure: Notes

INSPECT FUSE (S-HTR)

Remove the S-HTR fuse from the instrument panel J/B.

Measure the resistance according to the value(s) in the table below.

Resistance

Fig 1: Identifying S-HTR Location

Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002

RESISTANCE SPECIFICATIONS

Tester item	Condition	Specified condition
S-HTR fuse	Always	Below 1 Ω.

NG: REPLACE FUSE (S-HTR)

OK: Go to Next Step

CHECK HARNESS AND CONNECTOR (AIR CONDITIONING AMPLIFIER - SEAT CLIMATE CONTROL BLOWER)

Disconnect the connector from A/C amplifier.

Fig 2: Air Conditioning Amplifier Connector Wire Harness View
Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
Disconnect the connector from the seat climate control blower.

Measure the resistance according to the value(s) in the table below.

Resistance

Fig 3: Identifying Seat Climate Control Blower Connector Terminals

Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002

RESISTANCE SPECIFICATIONS

Tester connection (Symbols)	Condition	Specified condition
D38-16 (LOUT) - P12-3 (BCS)	Always	Below 1 Ω
D38-16 (LOUT) - P11-3 (BBS)	Always	Below 1 Ω
D38-8 (ROUT) - O14-3 (BCS)	Always	Below 1 Ω
D38-8 (ROUT) - O15-3 (BBS)	Always	Below 1 Ω
D38-16 (LOUT) - Body ground	Always	10 kΩ or higher
D38-8 (ROUT) - Body ground	Always	10 kΩ or higher

NG: REPAIR OR REPLACE HARNESS OR CONNECTOR

OK: Go to Next Step

CHECK HARNESS AND CONNECTOR (SEAT CUSHION CLIMATE BLOWER - SEAT BACK CLIMATE BLOWER)

Measure the resistance according to the value(s) in the table below.

Fig 4: Checking Harness And Connector (Seat Cushion Climate Blower - Seat Back Climate Blower)

Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002

Resistance

RESISTANCE SPECIFICATIONS

Tester connection (Symbols)	Condition	Specified condition
P11-2 (BFB+) - P12-2 (BFCL)	Always	Below 1 Ω
O15-2 (BFB+) - O14-2 (BFCL)	Always	Below 1 Ω
P11-2 (BFB+) - Body ground	Always	10 kΩ or higher
O15-2 (BFB+) - Body ground	Always	10 kΩ or higher

NG: REPAIR OR REPLACE HARNESS OR CONNECTOR

OK: Go to Next Step

CHECK HARNESS AND CONNECTOR (SEAT CLIMATE CONTROL BLOWER - BATTERY)

Measure the voltage according to the value(s) in the table below.

Standard

Fig 5: Identifying Seat Climate Control Blower Connector Terminals

Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002

TESTER CONNECTION AND SPECIFIED CONDITION

Tester connection (Symbols)	Condition	Specified condition
P12-1 (BFC+) - Body ground	Ignition switch off	Below 1 Ω
P12-1 (BFC+) - Body ground	Ignition switch on (IG)	10 to 14 V
O14-1 (BFC+) - Body ground	Ignition switch off	Below 1 Ω
O14-1 (BFC+) - Body ground	Ignition switch on (IG)	10 to 14 V

Result

RESULT DESCRIPTION

Result	Proceed to
OK	A
NG (w/o Smart key system)	B
NG (w/ Smart key system)	C

B: GO TO STARTING SYSTEM STARTING SYSTEM

C: GO TO PUSH BUTTON START SYSTEM SYSTEM DESCRIPTION

A: Go to Next Step

CHECK HARNESS AND CONNECTOR (SEAT CLIMATE CONTROL BLOWER - BODY GROUND)

Measure the resistance according to the value(s) in the table below.

Resistance

Fig 6: Identifying Seat Climate Control Blower Connector Terminals

RESISTANCE SPECIFICATIONS

Tester connection (Symbols)	Condition	Specified condition
P11-1 (BFB-) - Body ground	Always	Below 1 Ω
P12-4 (BFC-) - Body ground	Always	Below 1 Ω
O14-4 (BFC-) - Body ground	Always	Below 1 Ω
O15-1 (BFB-) - Body ground	Always	Below 1 Ω

NG: REPAIR OR REPLACE HARNESS OR CONNECTOR

OK: Go to Next Step

INSPECT AIR CONDITIONING AMPLIFIER
1. Remove the A/C amplifier with connectors still connected.
2. Turn the ignition switch on (IG).
  
  Fig 7: Air Conditioning Amplifier Connector Wire Harness Side
  Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
3. Measure the waveform according to the value(s).