Torque Specifications
3MZ-FE ENGINE MECHANICAL TORQUE SPECIFICATIONS
| Part Tightened | N*m | kgf*cm | ft.*lbf | |
|---|---|---|---|---|
| Engine hanger No. 2 at Cylinder head | 20 | 204 | 15 | |
| Knock sensor at Cylinder block | 20 | 204 | 15 | |
| Oil pressure switch assembly at Cylinder block | 15 | 152 | 11 | |
| Compressor mounting bracket No.1 at Cylinder block | 25 | 255 | 18 | |
| Generator bracket No. 1 at Cylinder block | 58 | 591 | 43 | |
| Pump bracket at Cylinder head | 32 | 326 | 24 | |
| Drive shaft bearing bracket at Cylinder block | 64 | 653 | 47 | |
| Exhaust manifold converter sub-assembly No. 2 at Cylinder head | 49 | 500 | 36 | |
| Exhaust manifold heat insulator No. 2 at Cylinder head | 8.5 | 87 | 75 in.*lbf | |
| Exhaust manifold converter sub-assembly RH at Cylinder head | 49 | 500 | 36 | |
| Intake manifold at Cylinder head | 15 | 153 | 11 | |
| Ignition coil assembly at Cylinder head cover | 8.0 | 82 | 71 in.*lbf | |
| Intake air surge tank at Intake manifold | 28 | 286 | 21 | |
| Surge tank stay bolt | 20 | 204 | 15 | |
| Engine hanger No. 2 at Cylinder head | 39 | 398 | 29 | |
| Engine hanger No. 1 at Intake air surge tank | 39 | 398 | 29 | |
| Manifold stay No. 2 at Exhaust manifold converter sub-assembly | 49 | 500 | 36 | |
| Manifold stay No. 2 at Automatic transaxle assembly | 49 | 500 | 36 | |
| Engine mounting insulator RH at Engine mounting bracket | 95 | 969 | 70 | |
| Engine mounting insulator LH at Automatic transaxle assembly | 95 | 969 | 70 | |
| Engine mounting insulator FR at Automatic transaxle assembly | 87 | 887 | 64 | |
| Vane pump assembly at Pump bracket | 43 | 439 | 32 | |
| Vane pump assembly at Engine mounting bracket | 43 | 439 | 32 | |
| Frame side rail plate sub-assembly at Front frame assembly | Bolt A | 85 | 867 | 63 |
| Bolt B | 32 | 326 | 24 | |
| Nut | 32 | 326 | 24 | |
| Front suspension member brace rear at Front frame assembly | Bolt C | 85 | 867 | 63 |
| Bolt D | 32 | 326 | 24 | |
| Nut | 32 | 326 | 24 | |
| Compressor and magnetic clutch at Compressor mounting bracket No.1 | Bolt | 25 | 250 | 18 |
| Nut | 26 | 260 | 19 | |
| Generator belt adjusting bar at Cylinder block | Nut A | 43 | 438 | 32 |
| Bolt B | 18 | 184 | 13 | |
| Bolt C | 8.0 | 82 | 71 in.*lbf | |
| Generator bracket No. 2 at Transverse engine, engine mounting bracket | 28 | 286 | 21 | |
| Intermediate shaft sub-assembly | 35 | 357 | 26 | |
| Drive plate and ring gear at Torque converter | 41 | 418 | 30 | |
| Flywheel housing under cover at Automatic transaxle assembly | 7.8 | 80 | 69 in.*lbf | |
| Front suspension arm at Lower ball joint | 75 | 764 | 55 | |
| Tie rod end at Steering knuckle | 49 | 500 | 36 | |
| Front axle hub nut at Front drive shaft | 294 | 2,998 | 217 | |
| Front stabilizer link assembly at Front suspension | 74 | 755 | 55 | |
| V-bank cover at Cylinder head cover | 7.9 | 81 | 70 in.*lbf | |
| Engine mounting stay No. 2 RH at Transverse engine, engine mounting bracket | 64 | 653 | 47 | |
| Engine moving control rod (See page) | Bolt A | 64 | 653 | 47 |
| Bolt B | 23 | 235 | 17 | |
| Camshaft sub-gear at Main gear | 5.4 | 55 | 48 in.*lbf | |
| Engine rear oil seal retainer at Cylinder block 8.0 | 82 | 71 | in.*lbf | |
| Oil pump assembly at Cylinder block (See page ) | 10 mm head 8.0 | 82 | 71 | in.*lbf |
| 12 mm head | 20 | 204 | 15 | |
| 14 mm head | 43 | 439 | 32 | |
| Crank position sensor at Oil pump assembly | 8.0 | 82 | 71 in.*lbf | |
| Oil pan baffle plate at Oil pan sub-assembly | 8.0 | 82 | 71 in.*lbf | |
| Oil pan sub-assembly at Cylinder block (See page ) | 10 mm head | 8.0 | 82 | 71 in.*lbf |
| 12 mm head | 20 | 204 | 15 | |
| Oil strainer sub-assembly at Oil pan sub-assembly | 8.0 | 82 | 71 in.*lbf | |
| Oil pan sub-assembly No. 2 at Oil pan sub-assembly | 8.0 | 82 | 71 in.*lbf | |
| Oil pan drain plug at Oil pan sub-assembly No. 2 | 45 | 459 | 33 | |
| Water inlet housing at Cylinder block | 8.0 | 82 | 71 in.*lbf | |
| Cylinder head at Cylinder block | 12 pointed head 1st | 54 | 551 | 40 |
| 2nd | Turn 90° | Turn 90° | Turn 90° | |
| Recessed head | 19 | 189 | 14 | |
| Camshaft bearing cap at Cylinder head | 16 | 163 | 12 | |
| Timing belt plate at Oil pump assembly | 8.0 | 82 | 71 in.*lbf | |
| Water pump assembly at Cylinder block | 8.0 | 82 | 71 in.*lbf | |
| Oil level gage guide at Cylinder block | 8.0 | 82 | 71 in.*lbf | |
| Oil filter union at Cylinder block | 30 | 306 | 22 | |
| Timing belt idler bracket at Cylinder block | 28 | 286 | 21 | |
| Timing belt No. 3 cover at Cylinder head | 8.5 | 87 | 76 in.*lbf | |
| Camshaft timing pulley at Camshaft | 125 | 1,275 | 92 | |
| Timing belt idler sub-assembly No. 2 at Timing belt idler bracket | 43 | 438 | 32 | |
| Timing belt idler sub-assembly No. 1 at Cylinder block | 34 | 347 | 25 | |
| Chain tensioner assembly No. 1 at Oil pump assembly | 27 | 280 | 20 | |
| Transverse engine, engine mounting bracket at Cylinder block | 28 | 286 | 21 | |
| Timing belt No. 2 cover at Timing belt No. 3 cover | 8.5 | 87 | 76 in.*lbf | |
| Timing belt No. 1 cover at Oil pump assembly | 8.5 | 87 | 76 in.*lbf | |
| Crankshaft pulley at Crankshaft | 215 | 2,192 | 159 | |
| Camshaft position sensor at Cylinder head | 8.0 | 82 | 71 in.*lbf | |
| Cylinder head cover at Cylinder head | 8.0 | 82 | 71 in.*lbf | |
| Spark plug at Cylinder head | 18 | 184 | 13 | |
| Vane pump assembly at Adjusting strut | 43 | 439 | 32 | |
| Generator at Generator bracket | 58 | 591 | 43 | |
| Generator at Adjusting bar | 18 | 184 | 13 | |
| Front suspension brace upper at Body | 80 | 816 | 59 | |
| Water outlet at Cylinder head | 15 | 153 | 11 | |
| Exhaust manifold heat insulator No. 2 at Exhaust manifold LH | 8.5 | 87 | 55 in.*lbf | |
| Exhaust pipe support bracket No. 1 at Automatic transaxle assembly | 21 | 214 | 15 | |
| Drive plate & ring gear sub-assembly at Crankshaft | 83 | 846 | 61 | |
| W/head straight screw plug No. 1 at Cylinder head | 44 | 449 | 32 | |
| W/head straight screw plug No. 2 at Cylinder head | 44 | 449 | 32 | |
| Main bearing cap at Cylinder block | 12 pointed head 1st | 22 | 224 | 16 |
| 2nd | Turn 90° | Turn 90° | Turn 90° | |
| 6 pointed head | 27 | 275 | 20 | |
| Connecting rod cap at Connecting rod | 1st | 25 | 250 | 18 |
| 2nd | Turn 90° | Turn 90° | Turn 90° | |
| Cylinder block w/head straight screw No. 1 plug at Cylinder block | 30 | 306 | 22 | |
| Cylinder block w/head straight screw No. 2 plug at Cylinder block | 50 | 510 | 37 | |
| Cylinder block w/head straight screw No. 3 plug at Cylinder block | 30 | 306 | 22 | |
| Water seal plate at Cylinder block | 18 | 184 | 13 | |
| Cylinder block water drain cock sub-assembly at Cylinder block | 39 | 398 | 29 | |