LEMON Manuals: Even more car manuals for everyone
Home >> Toyota >> 2006 >> Camry Solara SLE, 2D Convertible >> Repair and Diagnosis >> Engine Performance >> Tune-Up >> Engine Ignition System (3MZ-FE) >> Ignition System >> On-Vehicle Inspection

On-Vehicle Inspection

NOTE: In the following step, the terms "cold" and "hot" refer to the temperature of the coils. "Cold" means approximately -10°C (14°F) to 50°C (122°F). "Hot" means approximately 50°C (122°F) to 100°C (212°F).
  1. INSPECT IGNITION COIL ASSEMBLY (WITH IGNITER) AND PERFORM SPARK TEST 
    1. Check for DTCs.
      NOTE: If a DTC is present, perform a troubleshooting in accordance with the procedure for that DTC.
    2. Check if sparks occur.
      1. Remove the V-bank cover (See REMOVAL ).
      2. Remove the intake air surge tank (See INSTALLATION ).
      3. Remove the ignition coils.
      4. Using a 16 mm plug wrench, remove the spark plugs.
      5. Install the spark plugs to each ignition coil and connect the ignition coil connectors.
      6. Disconnect the 6 injector connectors.
      7. Ground the spark plugs.
      8. Check if sparks occur at each spark plug while the engine is being cranked.
        NOTE: Do not crank the engine for more than 2 seconds.

        HINT:

        If sparks do not occur, do the following test (See Procedure "A"):

      9. Using a 16 mm plug wrench, install the spark plugs.

        Torque: 25 N*m (255 kgf*cm, 18 ft.*lbf) 

      10. Install the ignition coils.

        Torque: 8 N*m (82 kgf*cm, 71 in.*lbf) 

      11. Install the intake air surge tank (See INSTALLATION ).
      12. Install the V-bank cover (See INSTALLATION ).
    3. Spark test (Procedure "A")
      1. Check if wire harness side connector of ignition coil (with igniter) is secure.

        Result: 

        RESULT REFERENCE (1 OF 3)

        Result Proceed to
        NG Connect securely.
        OK Go to next step.
      2. Perform spark test with a different ignition coil (with igniter).
        1. Replace current ignition coil (with igniter) with a different functioning ignition coil (with igniter).
        2. Perform spark test again.

        Result: 

        RESULT REFERENCE (2 OF 3)

        Result Proceed to
        OK Replace faulty ignition coil (with igniter).
        NG Go to next step.
      3. Check power supply to ignition coil (with igniter).
        1. Turn the ignition switch ON.
        2. Check that there is battery voltage at ignition coil positive (+) terminal.

        Result: 

        RESULT REFERENCE (3 OF 3)

        Result Proceed to
        NG Check wiring between ignition switch to ignition coil (with igniter).
        OK Go to next step.
      4. Check resistance of VVT SENSOR  .

        Standard resistance 

        SPECIFIED CONDITION RESISTANCE REFERENCE

        Temperature Specified condition
        Cold 835 to 1,400 Ω
        Hot 1,060 to 1,645 Ω

        Result: 

        RESULT REFERENCE

        Result Proceed to
        NG Replace VVT sensor.
        OK Go to next step.
      5. Check resistance of crankshaft position sensor (See VVT SENSOR  ).

        Standard resistance 

        SPECIFIED CONDITION RESISTANCE REFERENCE

        Temperature Specified condition
        Cold 1,630 to 2,740 Ω
        Hot 2,065 to 3,225 Ω

        Result: 

        RESULT REFERENCE (1 OF 2)

        Result Proceed to
        NG Replace crankshaft position sensor.
        OK Go to next step.
      6. Check IGT signal from ECM (See FAIL-SAFE CHART ).

        Result: 

        RESULT REFERENCE (2 OF 2)

        Result Proceed to
        NG Check ECM.
        OK Repair wiring between ignition coil and ECM.
scientia non olet · About LEMON Manuals