Data List / Active Test

DATA LIST

HINT:

By accessing the DATA LIST displayed on the intelligent tester, you can perform such functions as reading the values of switches and sensors without removing any parts. Reading the DATA LIST is the first step of troubleshooting and is one method to shorten labor time.

Connect the intelligent tester to the DLC3.
Turn the engine switch on (IG).

Following the display on the tester, select "DATA LIST".

PWR SOURCE CTRL (Power source control ECU):

DATA LIST

Item	Measurement Item / Range (Display)	Normal Condition	Diagnostic Note
SHIFT P SIG	Status of shift P position switch / ON or OFF	ON: Shift lever is P position OFF: Shift lever is non-P position	-
STR UNLOCK SW	Status of steering unlock switch / ON or OFF	ON: Steering unlock switch is UNLOCK OFF: Steering unlock switch is LOCK	-
STOP LAMP SW1	Status of stop light switch1 / ON or OFF	ON: Brake pedal pressed OFF: Brake pedal depressed	-
START SW1	Status of start switch1 / ON or OFF	ON: Engine switch is ON (IG) OFF: Engine switch is OFF	-
START SW2	Status of start switch2 / ON or OFF	ON: Engine switch is ON (IG) OFF: Engine switch is OFF	-
N SW/C SW	Status of Neutral SW / ON or OFF	ON: Shift lever is N position OFF: Shift lever is non-N position	-
RATCH CIRCUIT	Status of ratch circuit / ON or OFF	ON: Engine switch is ON (IG) OFF: Engine switch is OFF or ON (ACC) or ENGINE START	-
IG1 RELAY MON1	Status of ignition1 relay monitor (outside) / ON or OFF	ON: Engine switch is ON (IG) OFF: Engine switch is OFF	-
IG1 RELAY MON2	Status of ignition1 relay monitor (inside) / ON or OFF	ON: Engine switch is ON (IG) OFF: Engine switch is OFF	-
IG2 RELAY MON1	Status of ignition2 relay monitor (outside) / ON or OFF	ON: Engine switch is ON (IG) OFF: Engine switch is OFF	-
IG2 RELAY MON2	Status of ignition2 relay monitor (inside) / ON or OFF	ON: Engine switch is ON (IG) OFF: Engine switch is OFF	-
ST RELAY MON	Status of starter relay monitor / ON or OFF	ON: ST relay is ON OFF: ST relay is OFF	-
ST REQUEST SIG	Status of starter requesting signal monitor / ON or OFF	ON: ST relay is ON OFF: ST relay is OFF	-
ACC RELAY MON	Status of ACC relay monitor / ON or OFF	ON: Engine switch is ON (ACC) OFF: Engine switch is OFF	-
ACC CUT SIG	Status of ACC relay cut signal / ON or OFF	ON: Engine switch is OFF OFF: Engine switch is ON (ACC)	-
VEHICLE SPD SIG	Status of vehicle speed signal / STOP or RUN	ON: Vehicle is stopped OFF: Vehicle is running	-
E/G COND	Status of engine condition / STOP or RUN	ON: Engine is stopped OFF: Engine is running	When engine condition is rotating
PWR COND	Status of power supply condition / ALL, ACC ON, IG1, IG2, ST ON	ALL: All relay is ON ACC ON: ACC relay is ON IG1: IG1 relay is ON IG2: IG2 relay is ON ST ON: ST relay is ON	When ready signal allows to be capable driving
#CODE	Status of Number of diagnosis codes / Min.: 0, Max.: 255	-	-

SMART KEY (Certification ECU):

DATA LIST

Item	Measurement Item / Range (Display)	Normal Condition	Diagnostic Note
D TOUCH SENSOR	Status of touch sensor front LH / ON or OFF	ON: Touch sensor is touched OFF: Touch sensor does not touched	When the outside handle of the driver's door is touched by a person who does not carry the key after "D SELECT SIG" of the ACTIVE TEST is performed, "D TOUCH SENSOR" in the DATA LIST turn on.
P TOUCH SENSOR	Status of touch sensor front RH / ON or OFF	ON: Touch sensor is touched OFF: Touch sensor does not touched	When the outside handle of the driver's door is touched by a person who does not carry the key after "P SELECT SIG" of the ACTIVE TEST is performed, "P TOUCH SENSOR" in the DATA LIST turn on.
DR TOUCH SENSOR	Status of touch sensor rear LH / ON or OFF	ON: Touch sensor is touched OFF: Touch sensor does not touched	-
DP TOUCH SENSOR	Status of touch sensor rear RH / ON or OFF	ON: Touch sensor is touched OFF: Touch sensor does not touched	-
D TRIGGER	Lock switch front LH / ON or OFF	ON: Lock switch is pushed OFF: Lock switch is not pushed	-
P TRIGGER	Lock switch front RH / ON or OFF	ON: Lock switch is pushed OFF: Lock switch is not pushed	-
DR TRIGGER	Lock switch rear LH / ON or OFF	ON: Lock switch is pushed OFF: Lock switch is not pushed	-
DP TRIGGER	Lock switch rear RH / ON or OFF	ON: Lock switch is pushed OFF: Lock switch is not pushed	-
TR/B-DOOR UNLK	Luggage compartment open switch condition / ON or OFF	ON: Luggage compartment open switch is pushed OFF: Luggage compartment open switch does not pushed	-
IG SW	Engine switch IG condition / ON or OFF	ON: Engine switch ON (IG) OFF: Engine switch OFF	-
ACC SW	Engine switch ACC condition / ON or OFF	ON: Engine switch ON (ACC) OFF: Engine switch OFF	-
IGNITION AREA	Ignition available area / FRONT or ALL	Customization status is displayed	-
PARK WAIT TIME	Parking wait time / 0.5s, 1.5s, 2.5s, 5s	Customization status is displayed	-
TRUNK OPEN MODE	Luggage compartment door open mode with vehicle locked / ON or OFF	Customization status is displayed	-
KEY LO-BATT WRN	Low key battery warning / ON or OFF	Customization status is displayed	-
UNMATCH V-ID	Unmatched vehicle-ID / YES or NO	YES: Key ID matches vehicle NO: Key ID does not match vehicle	-
NO RESPONSE	No response / YES or NO	YES: Response from key NO: No response from key	-
UNMATCH FORMAT	Unmatched response code and format / YES or NO	YES: Key ID code matches NO: Key ID code does not match	-
LOW BATTERY	Key low battery / YES or NO	YES: Key battery voltage drops NO: Key battery voltage is normal	-
WRONG CODE	ID code difference / YES or NO	YES: Key ID code matches NO: Key ID code does not match	-
WRONG C CODE	C code difference (Response) / YES or NO	YES: Key ID code matches NO: Key ID code does not match	-
P/S 10-MIN	Power save counter 10 minutes / Min.: 0, Max.: 255	The number of power saved for 10 minutes is displayed	-
P/S 5-DAY	Power save counter 5 days / Min.: 0, Max.: 255	The number of power saved for 5 days is displayed	-
P/S 14-DAY	Power save counter 14 days / Min.: 0, Max.: 255	The number of power saved for 10 days is displayed	-
WRONG ID CODE	ID code difference / YES or NO	YES: Key ID code matches NO: Key ID code does not match	-
WRONG ROL CODE	Rolling code difference / YES or NO	YES: Key rolling code matches NO: Key rolling code does not match	-
DOOR UNLOCK MOD	Door unlock mode / ALL, EACH, D_DOOR, SIDE	Mode status is displayed	-
FUNCTION CANCEL	Entry door lock function cancel / ON or OFF	Mode status is displayed	-
PERMIT(START)	PERMIT(START) / NG or OK	NG: Engine start without permission OK: Engine start permission	-
IMMOBILIZER	Immobilizer function status / SET or UNSET	SET: The key is not inside the cabin UNSET: Push the engine switch with the key inside the cabin with depressing the brake pedal	-
MASTER KEY	Master key / MATCH or NO MATCH	MATCH: Key code is sent NO MATCH: Unmatched key code	-
SUB KEY	Sub key / MATCH or NO MATCH	MATCH: Key code is sent NO MATCH: Unmatched key code	-
BCC	BCC malfunction / NG or OK	NG: Correct data sensing OK: Incorrect data sensing	-
STATUS	Abnormal status / NG or OK	NG: Malfunction OK: Normal	-
ENCRYPT CODE	Different encrypt code / NG or OK	NG: Data error OK: Normal	-
SERIAL NUMBER	Different serial number / NG or OK	NG: Data error OK: Normal	-
FRAME	Frame error / NG or OK	NG: Data error OK: Normal	-
RESPONSE	Response / NG or OK	NG: With no response OK: Those with a response	-
WIRLES COM ID	Wireless starter communication ID / Registered or No registered	-	-
WIRLES C-CODE	Wireless C code / Registered or No registered	-	-
SCLK SLEEP COND	Steering lock sleep condition / YES or NO	-	-
SCLK START COND	Steering lock start condition / YES or NO	-	-
STEERING LOCK	Steering lock / SET or UNSET	-	This status changes depending on the state of some sensors.
STEERING UNLOCK	Steering unlock / SET or UNSET	-	This status changes depending on the state of some sensors.
ENG START COND	Engine start condition / OK or NG	OK: Engine start permission NG: Engine start without permission	-
SENSOR VALUE	Sensor malfunction / NG (PAST) or OK	NG (PAST): Sensor malfunction OK: No malfunction	-
PWR SUPPLY SHORT	Short in ECU / NG (PAST) or OK	NG (PAST): Short in ECU OK: No malfunction	-
PWR SUPPLY OPEN	Open in ECU / NG (PAST) or OK	NG (PAST): Open in ECU OK: No malfunction	-
MTR DRIVER SHRT	Short in driver ECU / NG (PAST) or OK	NG (PAST): Short in driver ECU OK: No malfunction	-
MTR DRIVER OPEN	Open in driver ECU / NG (PAST) or OK	NG (PAST): Open in driver ECU OK: No malfunction	-
LCK/UNLCK REC	Steering lock command reception record / YES or NO	YES: Steering lock / unlock signal received NO: Steering lock / unlock signal not received	-
LCK BAR STUCK	Lock bar stuck malfunction / NG (PAST) or OK	NG (PAST): Lock bar stuck malfunction OK: No malfunction	-
PUSH START ERR	Push button start function malfunction / NG (PAST) or OK	NG (PAST): Malfunction in push button start OK: No malfunction	-
IG2 (LINER)	IG2 status / ON or OFF	ON: 10 to 14 V OFF: Below 1 V	-
IG (LIN)	LIN bus start-up status / ON or OFF	ON: LIN bus started-up OFF: LIN bus not started-up	-
IDBX SLEEP COND	ID code box sleep condition / YES or NO	YES: ID code box sleep available NO: ID code box sleep not available	-
IDBX START COND	ID code box start condition / YES or NO	YES: ID code box started-up NO: ID code box not started-up	-
EFI CODE RECEIV	EFI code receive / NG or OK	NG: EFI code does not receive OK: EFI code received	-
START RQST	ID code box start request condition / YES or NO	YES: ID code box start request condition NO: ID code box non-start request condition	-
CODE RQST	3 bit code request / NG or OK	NG: 3 bit code does not receive OK: 3 bit code received	-
S CODE MATCH	Code verification result / OK or NG	OK: Verification confirmed NG: Verification not conformed	-
L CODE MATCH	Code verification result / OK or NG	OK: Verification confirmed NG: Verification not conformed	-
UNLC RQ RECEIVE	Steering unlock request / YES or NO	YES: Steering unlock NO: Steering lock	-
LCK RQ RECEIVE	Steering lock request / YES or NO	YES / NO	-
START RQST-PAST	Engine start request / YES or NO	YES / NO	-
EFI COM	EFI communication / OK or NG	NG: EFI code does not receive OK: EFI code received	-
L CODE MATCH	Code verification result / OK or NG	OK: Verification confirmed NG (PAST): Verification not conformed	-
S CODE MATCH	Code verification result / OK or NG	OK: Verification confirmed NG (PAST): Verification not conformed	-
#CODE	Diagnostic trouble code / Min.: 0, Max.: 255	-	-

METER (Combination Meter):

DATA LIST

Item	Measurement Item / Range (Display)	Normal Condition	Diagnostic Note
SPEED METER	Vehicle speed / Min.: 0 km/h (0 mph), Max.: 255 km/h (158 mph)	Almost the same as the actual vehicle speed (Wheel driving)	-
TACHO METER	Engine speed / Min.: 0 rpm, Max.: 12,750 rpm	Almost the same as the actual engine speed (When engine is running)	-
KEY REMND VOLUM	Key remind warning volume / LARGE, MEDIUM, SMALL	Customization status is displayed	-
KEY REMND SOUND	Key remind warning sound / FAST, NORMAL, SLOW	Customization status is displayed	-

SMART KEY (Steering Lock):

DATA LIST

Item	Measurement Item / Range (Display)	Normal Condition	Diagnostic Note
KEY SW	Key unlock warning switch / ON or OFF	ON: The key is inside the cabin OFF: The key is not inside the cabin	-
IG SW	Status of ignition relay / ON or OFF	ON: Engine switch is ON (IG) OFF: Engine switch is OFF (IG)	-
IMMOBILIZER	Immobilizer system status / UNSET or SET	UNSET: Push the engine switch with the key inside the cabin while depressing the brake pedal SET: The key is not inside the cabin	-
RESPONSE	Transponder chip data / OK or NG	OK: With no response NG: Those with a response	-
FRAME	Transponder chip data / OK or NG	OK: Data OK NG: Data error	-
SERIAL NUMBER	Transponder chip data / OK or NG	OK: Data OK NG: Data error	-
ENCRYPT CODE	Transponder chip data / OK or NG	OK: Data OK NG: Data error	-
STATUS	Transponder chip data / OK or NG	OK: Data OK NG: Data error	-
BCC	Transponder chip data / OK or NG	OK: Correct data sensing NG: Incorrect data sensing	-
SUB KEY	Sub key code signal / MATCH or NO MATCH	MATCH: Sub key code is sent NO MATCH: Unmatched sub key	-
MASTER KEY	Master key code signal / MATCH or NO MATCH	MATCH: Master key code is sent NO MATCH: Unmatched master key	-
REGIST SUB CODE	Number of registered sub key / Min.: 0, Max.: 15	Number of registered sub key	-
REGIST MAS CODE	Number of registered master key / Min.: 0, Max.: 15	Number of registered sub key	-
REG CODE SPACE	Memory space for key code registration / NOT FULL or FULL	FULL: Impossible to register key code any more NOT FULL: Possible to register more key codes more	-
+B	Power source / BREAK or NORMAL	BREAK: Power source open NORMAL: Power source normal	-
ANTENNA COIL	Transponder key amplifier coil condition / FAIL or NORMAL	FAIL: Antenna coil is malfunctioning NORMAL: Antenna coil is normal	-
G-CODE DECISION	YES or NO	-	-
G-CODE SUPPORT	SUPPORT or NOT SUP	-	-
HAZARD ANS BACK	Hazard answer back / ON or OFF	ON: Hazard answer back function operates OFF: Hazard answer back function does not operate	-
WIRLS BUZZ RESP	Wireless door lock buzzer response / ON or OFF	ON: Wireless door lock buzzer sounds OFF: Wireless door lock buzzer does not sounds	-

ACTIVE TEST

HINT:

Perform the ACTIVE TEST using the intelligent tester to operate the motors of the front seat outer belts.

Performing the ACTIVE TEST is one of the methods to shorten labor time. It is possible to display the DATA LIST during the ACTIVE TEST.

Connect the intelligent tester to the DLC3.
Turn the engine switch on (IG).

Following the display on the tester, select the "ACTIVE TEST".

SMART KEY (Certification ECU):

ACTIVE TEST DATA LIST

Item	Vehicle Condition / Test Details	Diagnostic Note
IN LUG TUNER	Inside Trunk Tuner ON / OFF	-
OVERHEAD TUNER	Cabin Tuner ON / OFF	-
D TRANSMITTER	Door Oscillator (Front LH) ON / OFF	-
P TRANSMITTER	Door Oscillator (Front RH) ON / OFF	-
Fr TRANSMITTER	Cabin Oscillator (Front) ON / OFF	-
IN-BDR TRANSMTTR	Luggage Compartment Oscillator (Inner) ON / OFF	-
BDOOR TRANSMTTR	Luggage Compartment Oscillator (Outer) ON / OFF	-
D SELECT SIG	D-sheet Select ON/OFF	The same condition as when the key is brought near the vehicle will occur even if the key is not brought near the vehicle.
P SELECT SIG	P-sheet Select ON/OFF	The same condition as when the key is brought near the vehicle will occur even if the key is not brought near the vehicle.

METER (Combination Meter):

ACTIVE TEST DATA LIST

Item	Vehicle Condition / Test Details	Diagnostic Note
OPEN DOOR WARN	Open Door Warning Light ON / OFF	-
KEY REMND BUZZR	Key Remained Buzzer ON / OFF	-
WARNING BUZZER	Warning Buzzer ON / OFF	-
SMART KEY	Smart Key System Warning Light ON / OFF	-

SMART KEY (Steering Lock ECU):

ACTIVE TEST DATA LIST

Item	Vehicle Condition / Test Details	Diagnostic Note
SECURITY INDIC	Security Indicator Light ON / OFF	-

SMART KEY SYSTEM DIAGNOSIS MODE

HINT:

The smart key system diagnostic mode can be used to check that the key and each tuner operate normally without removing the tuners from the vehicle.
The smart key system diagnostic mode check is performed with the intelligent tester.

Connect the intelligent tester to the DLC3.
Turn the engine switch on (IG).
Following the display on the tester, select "SMART KEY" --> "ID UTILITY".

Select each "Item" and bring the key up to the action area in which the system can detect the key.

If the system functions normally, the wireless door lock buzzer sounds once.

SMART DIAG MODE:

SMART DIAG MODE REFERENCE CHART

Item	Tuner
D+OVERHEAD	Cabin
P+OVERHEAD	Cabin
DR+OVERHEAD	Cabin
PR+OVERHEAD	Cabin
FR+OVERHEAD	Cabin
RR+OVERHEAD	Cabin
IN-LUG+IN-LUG	Luggage
LUGG+OVERHEAD	Cabin
LUGG+IN-LUG	Luggage
IN-BDOR+OVERHEAD	Cabin
BDOR+OVERHEAD	Cabin
IMMOBI+AMP	Transponder key amplifier