Service Data
Suspension & Axle Service Data List
| Cold tire inflation pressure | 1ZZ-FE engine models | |||||||
| 195/60R15 88H P195/60R15 87H |
Front, rear | 210 kPa (2.1 kgf/cm2 , 29 psi) | ||||||
| 2ZZ-GE engine models | ||||||||
| 205/55R15 87V P205/55R15 87V 205/50R16 87V |
Front, rear | 220 kPa (2.2 kgf/cm2 , 32 psi) | ||||||
| Front Wheel alignment | Vehicle height | |||||||
| Tire size: 1B5/60R15, P195/60R15 | Front(1) | 190 mm (7.48 in.) | ||||||
| Rear(2) | 224 mm (8.82 in.) | |||||||
| Tire size: 205/55R15, P205/55R15 | Front(1) | 190 mm (7.48 in.) | ||||||
| Rear(2) | 226 mm (8.90 in.) | |||||||
| Tire size: 205/50R16 | Front(1) | 193 mm (7.60 in.) | ||||||
| Rear(2) | 225 mm (8.86 in.) | |||||||
| Camber | ||||||||
| 195/60R15, P195/60R15 | -0°28' ± 45' (-0.47° ± 0.75°) | |||||||
| 20S/55R15, P205/55R15 | -0°25' ± 45' (-0.42° ± 0.75°) | |||||||
| 205/50R16 | -0°29' ± 45' (-0.48° ± 0.75°) | |||||||
| Right-left error | 45' (0.75°) or less | |||||||
| Caster | ||||||||
| 195/60R15, P195/60R15 | 2°07' ± 45' (2.12° ± 0.75°) | |||||||
| 205/55R15, P205/55R15 | 2°01' ± 45' (2.02° ± 0.75°) | |||||||
| 205/50R16 | 2°02' ± 45' (2.03° ± 0.75°) | |||||||
| Right-left error | 45' (0.75°) or less | |||||||
| Steering axis inclination | ||||||||
| 195/60R15, P195/60R15 | 13°09' ± 45' (13.15° ± 0.75°) | |||||||
| 205/55R15, P205/55R15 | 13°04' ± 45' (13.07° ± 0.75°) | |||||||
| 205/50R16 | 13°12' ± 45' (13.20° ± 0.75°) | |||||||
| Right-left error | 45' (0.75°) or less | |||||||
| Toe-in (total) | 0° ± 12' (0° ± 0.2°, 0 ± 2 mm, 0 ± 0.08 in.) | |||||||
| Rack end length difference | 1.5 mm (0.059 in.) or less | |||||||
| Wheel angle | ||||||||
| 195/60R15, P195/60R15 | Inside wheel | 38°41' ± 2° (38.68° ± 2°) | ||||||
| Outside wheel: Reference | 33°20' (33.33°) | |||||||
| 205/55R15, P205/55R15 | Inside wheel | 38°46' ± 2° (38.77° ± 2°) | ||||||
| Outside wheel: Reference | 33°25' (33.42°) | |||||||
| 205/50R16 | Inside wheel | 38°38' ± 2° (38.63° ± 2°) | ||||||
| Outside wheel: Reference | 33°19' (33.32°) | |||||||
| Rear wheel alignment | Camber | -1°11' ± 45' (-1.18° ± 0.75°) | ||||||
| Right-left error | 45' (0.75°) or less | |||||||
| Toe-in (total) | 0°18' ± 12' (0.3° ± 0.2°, 3 ± 2 mm, 0.12 ± 0.08 in.) | |||||||
| Toe-in cross measurement difference | 6 mm (0.24 in.) or less | |||||||
| Front axle | Axle bearing backlash | Maximum | 0.05 mm (0.0020 in.) | |||||
| Axle hub deviation | Maximum | 0.07 mm (0.0028 in.) | ||||||
| Front drive shaft | Drive shaft standard length | |||||||
| 1ZZ-FE (A/T) | RH | 851.0 ± 5.0 mm (33.504 ± 0.197 in.) | ||||||
| LH | 565.9 ± 5.0 mm (22.279 ± 0.197 in.) | |||||||
| 1ZZ-FE (M/T) and 2ZZ-GE | RH | 845.5 ± 5.0 mm (33.287 ± 0.197 In.) | ||||||
| LH | 563.7 ± 5.0 mm (22.193 ± 0.197 in.) | |||||||
| Front suspension | Lower ball joint turning torque | 1.0 - 4.9 (N.m (10 - 50 kgf.cm, 8.7 - 43 in.***.lbf) | ||||||
| Stabilizer bar link ball joint turning torque | 0.05 - 1.0 N.m (0.5 - 10 kgf.cm, 0.4 - 3.7 in.***.lbf) | |||||||
| Rear axle | Axle bearing backlash | Maximum | 0.05 ram (0.0020 in.) | |||||
| Axle hub deviation | Maximum | 0.07 mm (0.0028 in.) | ||||||
| Rear suspension | Stabilizer bar link ball joint turning torque | 0.05 - 1.0 N.m (0.5 - 10 kgf.cm, 0.4 - 8.7 in.***.lbf) | ||||||
Measure the distance from the ground to the center of the front side lower suspension arm mounting bolt.
Measure the distance from the ground to the center of the rear side lower suspension arm suspension member side set bolt. |
||||||||