Body & Frame: Windows: Windshield: Installation

1. Using a knife, cut away any rough areas on the body.

   HINT:

   Leave the adhesive on the body as much as possible.

2. Clean the cut surface of the adhesive with a shop rag saturated in cleaner.

   HINT:

   Even if all the adhesive has been removed, clean the body.

Fig 1: Cleaning Cut Surface Of Adhesive

Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002

1. Remove the damaged No.2 stoppers and dams.
2. Using a scraper, remove the adhesive sticking to the glass.
3. Clean the glass with cleaner.

Fig 2: Removing Adhesive Sticking To Glass

Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002

REPLACE NO. 1 STOPPERS 

1. Remove the damaged stoppers.
2. Cut off the old adhesive around the stopper installation area.
   NOTE: Be careful not to damage the body.
3. Clean the installation area.
4. Attach new stoppers to the body so that the notches on the body will align with the stoppers as shown in the illustration.

Fig 3: Cutting Off Adhesive Around Stopper

Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002

HINT:

Make sure that the stoppers are installed facing the correct direction.

Attach new stoppers to the glass so that the ceramic notches on the glass will align with the stoppers as shown in the illustration.

HINT:

Make sure that the stoppers are installed facing the correct direction.

A: 

w/ No. 1 stopper: 7.7 +/- 0.5 (0.303 +/- 0.020 in.) 

w/o No. 1 stopper: 9.0 +/- 0.5 (0.354 +/- 0.020 in.) 

Fig 4: Attaching Stoppers To Glass

Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002

Install new dams with double-stick tape as shown in the illustration.

A: 7.0 mm (0.276 in.) 

Fig 5: Installing Dams With Double-Stick Tape

Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002

1. Place the glass in the correct position.
2. Check that all contacting parts of the glass rim are set perfectly even.
3. Place reference marks on the glass and body.
4. Remove the glass.

Fig 6: Placing Glass In Position

Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002

Using a cleaner, clean the contact surface which is black-colored area around the entire glass rim.

Fig 7: Cleaning Contact Surface Of Glass

Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002

Using a brush, coat Primer M to the exposed part of body on the vehicle side.

Fig 8: Coating Contact Surface Of Body With Primer

Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002

1. Using a brush or sponge, coat the edge of the glass and the contact surface with Primer G as shown in the illustration.
2. When the primer is coated wrongly to the area other than the specified, wipe it off with a clean shop rag before the primer dries.

Fig 9: Coating Contact Surface Of Glass With Primer

Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002

1. Cut off the tip of the cartridge nozzle.

   Part No. 08850-00801 or equivalent 

   HINT:

   After cutting off the tip, use all adhesive within the time described in the TEMPERATURE SPECIFICATIONS  below.

   TEMPERATURE SPECIFICATIONS
   
   

   Temperature	Tackfree time
   35°C (95°F)	15 minutes
   20°C (68°F)	100 minutes
   5°C (41°F)	8 hours

2. Load the cartridge into the sealer gun.
3. Coat the glass with adhesive as shown in the illustration.

   A: 12.5 mm (0.492 in.) 

   B: 8.0 mm (0.315 in.) 

Fig 10: Coating Glass With Adhesive

Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002

1. Install the glass, aligning the reference marks using a suction rubber.

   HINT:

   Check to see that the stoppers are attached to the body correctly.

2. Lightly press the glass front surface for close contact.
   Fig 11: Installing Windshield Glass & Molding

   Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
3. Correct insufficient or protruded adhesive agent using a spatula.

   HINT:

   Apply the adhesive agent up to the windshield glass edge.

   Fig 12: Applying Adhesive Agent Up To Windshield Glass Edge

   Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
4. Install a new windshield molding to the windshield glass before the adhesive agent hardens.

   HINT:

   Install the molding, aligning the center of molding with the center of body.

5. Remove any excessive adhesive agent before it hardens.
6. Hold the glass and molding in place securely with a protective tape or equivalent until the adhesive hardens.
   Fig 13: Installing Windshield Molding To Windshield Glass

   Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002

HINT:

Check that the 2 clips on the back side of the cowl louver are surely fixed to the body.

1. Operate the wiper motor once and turn the wiper switch OFF.
2. Install the wiper arms and tighten the nuts by hand.
3. Adjust the installation positions of the wiper arms to the positions as shown in the illustration.

   A: 30 +/- 7.5 mm (1.8 +/- 0.295 in.) 

4. Torque the nuts.

   Torque: 32 N.m (323 kgf.cm, 23 ft.lbf) 

5. Install the 2 wiper arm head caps.

Fig 14: Adjusting Installation Positions Of Wiper Arms

Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002