LEMON Manuals: Even more car manuals for everyone
Home >> Toyota >> 2004 >> Land Cruiser >> Repair and Diagnosis >> Accessories & Equipment >> Entertainment Systems >> Audio System >> Troubleshooting

Audio System: Troubleshooting

  1. DIAGNOSIS FUNCTION (Main AVC-LAN) 
    1. Diagnosis start-up

      For shifting to diagnosis mode, turn the ignition switch ON and push the "DISC" switch 3 times while pressing "ch1" and "ch6" switches.

      HINT:

      To exit the diagnosis mode, push the "DISC" switch for 1.7 sec. or turn the ignition switch to ACC or OFF.

    2. Element check mode

      After the diagnosis start-up, the system enters the element check mode. Check that the all elements light up.

      HINT:

      By pressing the "TUNE UP" switch, the system enters the "Service Check Mode".

    3. Switch check mode
      1. Element check mode is started at the same time with the switch check mode.
      2. Check that there is a beep sound when any switch is pressed.

      HINT:

      By pressing "TUNE UP" switch, the system enters the "Service Check Mode".

      Fig 1: Locating Different Switches Of Audio System (1 Of 2)
      G02904529Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
  2. Service check mode
    1. After the element check and switch check is completed, the system enters service check mode when "TUNE UP" switch is pressed.
    2. Error codes over the tuner and connected equipments are displayed on the screen of the tuner. Results for each check are displayed as follows:
      • Good:

        No DTC is detected for both "System Check Confirmation" and "Diagnosis Memory Response".

      • nCon:

        The component does not respond to the "Diagnosis On Instruction" command.

        Applicable to only the system where connected components are limited to be used.

      • ECHn:

        Application of new version has been confirmed by the "Diagnosis On Check", and there is one or more DTC which indicates "Replacement" in the "System Check Result Response" or "Diagnosis Memory Response".

      • CHEC:

        Application of new version has been confirmed by the "Diagnosis On Check", and there is no DTC which indicates "Replacement" in the "System Check Result Response" or "Diagnosis Memory Response", but one or more DTC which indicates "Check" is identified.

      • Old:

        Application of old version is confirmed by the "Diagnosis On Check", and DTC is identified in the "System Check Result Response" or "Diagnosis Memory Response".

      • nrES:

        No response is identified to the "System Check Start Instruction" and "Request for System Check Result" commands.

    HINT:

    • Check the present and past condition of components by performing the System Check and collecting stored DTC memories.
    • Check results are displayed as one of the following six indications: "good", "ECHn", "CHEC","nCon", "Old" or "nrES".
      Fig 2: Locating Different Switches Of Audio System (2 Of 2)
      G02904530Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
  3. Display Screen for Service Check.

    Example: 

    Connection parts (physical address): Radio receiver (P190), RSA ECU (P1F4), DVD player (P1A0)

    Fig 3: Service Check Block Diagram
    G02904531Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
  4. "ECHn" Detail Display Mode Screen
    Fig 4: "ECHn" Detail Display Mode Block Diagram
    G02904532Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
  5. "CHEC" Detail Display Mode Screen
    Fig 5: "CHEC" Detail Display Mode Block Diagram
    G02904533Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
  6. "Old" Detail Display Mode Screen
    Fig 6: "Old" Detail Display Mode Block Diagram
    G02904534Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
  7. DIAGNOSIS FUNCTION (Sub AVC-LAN) 

    HINT:

    As starting Main AVC-LAN to operate the diagnosis mode, Sub AVC-LAN is automatically to the mode. Perform the diagnosis mode operation on the RSA panel.

    1. Element check mode

      After the diagnosis start-up, the system enters the element check mode. Check that the all elements light up.

      HINT:

      By pressing the "TUNE UP" switch, the system enters the "Service Check Mode".

    2. Switch check mode
      1. Element check mode is started at the same time with the switch check mode.
      2. Check that there is a beep sound when any switch is pressed.

        HINT:

        By pressing "TUNE UP" switch, the system enters the "Service Check Mode".

        Fig 7: Locating Tune Up & Down Switch For "Service" Check Mode (1 Of 2)
        G02904535Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
    3. Service check mode
      1. After the element check and switch check is completed, the system enters service check mode when "TUNE UP" switch is pressed.
      2. Error codes over the tuner and connected equipments are displayed on the screen of the tuner. Results for each check are displayed as follows:
        • Good:

          No DTC is detected for both "System Check Confirmation" and "Diagnosis Memory Response".

        • nCon:

          The component does not respond to the "Diagnosis On Instruction" command.

          Applicable to only the system where connected components are limited to be used.

        • ECHn:

          Application of new version has been confirmed by the "Diagnosis On Check", and there is one or more DTC which indicates "Replacement" in the "System Check Result Response" or "Diagnosis Memory Response".

        • CHEC:

          Application of new version has been confirmed by the "Diagnosis On Check", and there is no DTC which indicates "Replacement" in the "System Check Result Response" or "Diagnosis Memory Response", but one or more DTC which indicates "Check" is identified.

        • Old:

          Application of old version is confirmed by the "Diagnosis On Check", and DTC is identified in the "System Check Result Response" or "Diagnosis Memory Response".

        • nrES:

          No response is identified to the "System Check Start Instruction" and "Request for System Check Result" commands.

      HINT:

      • Check the present and past condition of components by performing the System Check and collecting stored DTC memories.
      • Check results are displayed as one of the following six indications: "good", "ECHn", "CHEC","nCon", "Old" or "nrES".
        Fig 8: Locating Tune Up & Down Switch For Service Check Mode (2 Of 2)
        G02904536Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
    4. Display Screen for Service Check.

      Example: 

      Connection parts (physical address): Radio receiver (P190), RSA ECU (P1F4), DVD player (P1A0)

      Fig 9: Service Check Block Diagram
      G02904537Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
    5. "ECHn" Detail Display Mode Screen
      Fig 10: ECHn Detail Display Mode Block Diagram
      G02904538Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
    6. "CHEC" Detail Display Mode Screen
      Fig 11: "CHEC" Detail Display Mode Block Diagram
      G02904539Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
    7. "Old" Detail Display Mode Screen
      Fig 12: "Old" Detail Display Mode Block Diagram
      G02904540Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
  8. DIAGNOSIS CODE LIST 

    w/ Navigation system

    Physical address: 190 Radio receiver assembly

    HINT:

    *1: Even if no failure is detected, it may be stored depending on the battery condition or voltage for starting an engine.

    *2: It may be stored when the engine key is turned 1 min. again after engine start.

    *3: It may be stored when the engine key is turned again after engine start.

    *4: When 210 sec. has passed after pulling out the power supply connector of the master component with the ignition switch in ACC or ON, this code is stored.

    Fig 13: Identifying Radio Receiver Assembly DTC's (1 Of 2)
    G02904541Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
    Fig 14: Identifying Radio Receiver Assembly DTC's (2 Of 2)
    G02904542Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002

    Physical address: 440 Stereo component amplifier

    HINT:

    *1: Even if no failure is detected, it may be stored depending on the battery condition or voltage for starting an engine.

    *2: It may be stored when the engine key is turned 1 min. again after engine start.

    *3: It may be stored when the engine key is turned again after engine start.

    *4: When 210 sec. has passed after pulling out the power supply connector of the master component with the ignition switch in ACC or ON, this code is stored.

    Fig 15: Identifying Stereo Component Amplifier DTC's
    G02904543Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002

    Physical address: 1F4 RSA Panel (Main AVC-LAN)

    HINT:

    *1: Even if no failure is detected, it may be stored depending on the battery condition or voltage for starting an engine.

    *2: It may be stored when the engine key is turned 1 min. again after engine start.

    *3: It may be stored when the engine key is turned again after engine start.

    *4: When 210 sec. has passed after pulling out the power supply connector of the master component with the ignition switch in ACC or ON, this code is stored.

    Fig 16: Identifying 1F4 RSA Panel DTC's
    G02904544Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002

    Physical address: 16A, 16C RSA Panel (Sub AVC-LAN)

    HINT:

    *1: Even if no failure is detected, it may be stored depending on the battery condition or voltage for starting an engine.

    *2: It may be stored when the engine key is turned 1 min. again after engine start.

    *3: It may be stored when the engine key is turned again after engine start.

    *4: When 210 sec. has passed after pulling out the power supply connector of the master component with the ignition switch in ACC or ON, this code is stored.

    Fig 17: Identifying 16A, 16C RSA Panel DTC's
    G02904545Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002

    Physical address: 1A0 DVD Auto Player

    HINT:

    *1: Even if no failure is detected, this code may be stored depending on the battery condition or voltage for starting an engine.

    *2: This code may be stored when the engine key is turned again 1 min. after engine start.

    *3: This code may be stored when the engine key is turned again after engine start.

    *4: When 210 sec. has passed after pulling out the power supply connector of the master component with the ignition switch in ACC or ON, this code is stored.

    Fig 18: Identifying 1A0 DVD Auto Player DTC's
    G02904546Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002

    Physical address: 250 (DVD Auto Changer) (Sub AVC-LAN)

    Fig 19: Identifying 250 (DVD Auto Changer) DTC's (1 Of 2)
    G02904547Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
    Fig 20: Identifying 250 (DVD Auto Changer) DTC's (2 Of 2)
    G02904548Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
  9. PROBLEM SYMPTOMS TABLE 
    NOTE: When replacing the internal mechanism (computer part) of the audio system, be careful that no part of your body or clothing comes in contact with the terminals of the leads from the IC, etc. of the replacement part (spare part). 

    HINT:

    This inspection procedure is a simple troubleshooting which should be carried out on the vehicle during system operation and was prepared on the assumption of system component troubles (except for the wires and connectors, etc.).

    Always inspect the trouble taking the following items into consideration.

    • Open or short circuit of the wire harness
    • Connector or terminal connection fault
    Fig 21: Identifying Problem Symptoms
    G02904549Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002

The term "AM" includes LW, MW and SW, and the term "FW" includes UKW.

  1. RADIO NOT OPERATING WHEN POWER SWITCH TUNED TO "ON" 
    Fig 22: Problem Symptom Flow Diagram (Radio) When Radio Not Operating, Power Switch "On"
    G02904550Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
  2. Radio DISPLAY INDICATES WHEN POWER SWITCH TURNED TO "ON", BUT NO SOUND (INCLUDING "NOISE") IS PRODUCED 
    Fig 23: Problem Symptom Flow Diagram (Radio) When Power Switch "On" But No Sound Produced.
    G02904551Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
  3. Radio NOISE PRESENT, BUT AM-FM NOT OPERATING 
    Fig 24: Problem Symptom Flow Diagram (Radio) When Noise Present, But-FM Not Operating
    G02904552Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
  4. Radio ANY AM OR FM DOES NOR WORK 5 FEW PRESET TUNING BANDS 
    Fig 25: Problem Symptom Flow Diagram (Radio) When Any AM Or FM Does Not Work Few Present Tuning Bands
    G02904553Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
  5. Radio POOR RECEPTION 
    Fig 26: Problem Symptoms Flow Diagram (Radio) For Poor Reception
    G02904554Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
  6. Radio SOUND QUALITY POOR 
    Fig 27: Problem Symptom Flow Diagram (Radio) For Poor Sound Quality
    G02904555Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
  7. Radio PRESET MEMORY DISAPPEARS 
    Fig 28: Problem Symptom Flow Diagram (Radio) When Preset Memory Disappears
    G02904556Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
  8. Tape Player CASSETTE TAPE CANNOT BE INSERTED 
    Fig 29: Problem Symptom Flow Diagram (Tape Player) When Cassette Tape Can Not Be Inserted
    G02904557Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
  9. Tape Player CASSETTE TAPE INSERTED, BUT NO POWER 
    Fig 30: Problem Symptom Flow Diagram (Tape Player) When Cassette Tape Inserted, But No Power
    G02904558Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
  10. Tape Player POWER COMING IN, BUT TAPE PLAYER NOT OPERATING 
    Fig 31: Problem Symptom Flow Diagram Tape Player (When Power Coming In, But Tape Player Not Operating)
    G02904559Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
  11. Tape Player ANY SPEAKER DOES NOT WORK 
    Fig 32: Problem Symptom Flow Diagram Tape Player (Speaker Not Working)
    G02904560Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
  12. Tape Player SOUND QUALITY POOR (VOLUME FAINT) 
    Fig 33: Problem Symptom Flow Diagram Tape Player (Sound Quality Poor)
    G02904561Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
  13. Tape Player TAPE JAMMED MALFUNCTION WITH TAPE SPEED OR AUTO-REVERSE 
    Fig 34: Problem Symptom Flow Diagram Tape Player (When Tape Jammed Malfunction With Tape Speed Or Auto-Reverse)
    G02904562Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
  14. Tape Player CASSETTE TAPE WILL NOT BE EJECTED 
    Fig 35: Problem Symptom Flow Diagram Tape Player (When Cassette Tape Will Not Be Ejected)
    G02904563Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
  15. CD Player CD CANNOT BE INSERTED 
    Fig 36: Problem Symptom Flow Diagram CD Player (When CD Cannot Be Inserted)
    G02904564Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
  16. CD Player CD INSERTED, BUT NO POWER 
    Fig 37: Problem Symptom Flow Diagram CD Player (When CD Inserted, But To Power)
    G02904565Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
  17. CD Player POWER COMING IN, BUT CD PLAYER NOT OPERATING 
    Fig 38: Problem Symptom Flow Diagram CD Player (When Power Coming In, But CD Player Not Operating)
    G02904566Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
  18. CD Player SOUND JUMPS 
    Fig 39: Problem Symptom Flow Diagram CD Player (When Sound Jumps)
    G02904567Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
  19. CD Player SOUND QUALITY POOR (VOLUME FAINT) 
    Fig 40: Problem Symptom Flow Diagram CD Player (When Sound Quality Poor)
    G02904568Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
  20. CD Player ANY SPEAKER DOES NOT WORK 
    Fig 41: Problem Symptom Flow Diagram CD Player (Speaker Not Working)
    G02904569Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
  21. CD Player CD WILL NOT BE EJECTED 
    Fig 42: Problem Symptom Flow Diagram CD Player (When CD Will Not Be Ejected)
    G02904570Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
  22. Power Amplifier NO POWER COMING IN 
    Fig 43: Problem Symptom Flow Diagram Power Amplifier (When No Power Coming In)
    G02904571Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
  23. Power Amplifier POWER COMING IN, BUT WOOFER (POWER) AMPLIFIER NOT OPERATING 
    Fig 44: Problem Symptom Flow Diagram Power Amplifier (When No Power Coming In, But Woofer (Power) Amplifier Not Operating)
    G02904572Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
  24. Power Amplifier ANY SPEAKER DOES NOT WORK 
    Fig 45: Problem Symptom Flow Diagram (Power Amplifier) When Speakers Not Working
    G02904573Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
  25. NOISE OCCURS 
    Fig 46: Problem Symptom Flow Diagram (When Noise Occurs)
    G02904574Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
  26. NOISE PRODUCED BY VIBRATION OR SHOCK WHILE DRIVING 
    Fig 47: Problem Symptoms Block Diagram (Noise Produced By Vibration Or Shock While Driving)
    G02904575Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
  27. NOISE PRODUCED WHEN ENGINE STARTS 
    Fig 48: Problem Symptoms Block Diagram (Noise Produced When Engine Starts)
    G02904576Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
  28. Steering Pad Switch A AUDIO SYSTEM CANNOT BE OPERATED WITH STEERING PAD SWITCH 
    Fig 49: Problem Symptoms Block Diagram, Steering Pad Switch (Audio System Cannot Be Operated With Steering Pad Switch)
    G02904577Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
  29. Rear Seat Audio QUALITY OF SOUND FROM HEADPHONE TERMINAL IS POOR OR NO SOUND 
    Fig 50: Problem Symptoms Block Diagram, Rear Seat Audio (Headphone Terminal Sound Quality Poor Or No Sound Heard)
    G02904578Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002