Specifications Index
CAMRY SPECIFICATIONS INDEX
| System | Specifications/Procedures | ||
|---|---|---|---|
| Air Conditioning | |||
| Service | SPECIFICATIONS | ||
| Torque | TORQUE SPECIFICATIONS | ||
| Axle Nut/Hub Nut (Front) | 217 ft.lbs (294 N.m) | ||
| Axle Hub-To-Axle Carrier Bolts (Rear) | 59 ft.lbs (80 N.m) | ||
| Battery | NA | ||
| Brakes | |||
| Bleeding Sequence | BLEEDING BRAKE SYSTEM | ||
| Disc Brakes | DISC BRAKE SPECIFICATIONS | ||
| Drum Brake (Parking) | DRUM BRAKE SPECIFICATIONS | ||
| Torque | TORQUE SPECIFICATIONS | ||
| Charging | |||
| Generator | |||
| 2.4L (2AZ-FE) | ON-VEHICLE INSPECTION | ||
| 3.0L (1MZ-FE) | ON-VEHICLE INSPECTION | ||
| Torque | |||
| 2.4L (2AZ-FE) | TORQUE SPECIFICATIONS | ||
| 3.0L (1MZ-FE) | TORQUE SPECIFICATIONS | ||
| Drive Belts | |||
| Adjustment | BELT ADJUSTMENT | ||
| Belt Routing | DRIVE BELT ROUTING | ||
| Engine Cooling | |||
| General Service Specifications | COOLING SYSTEM SPECIFICATIONS | ||
| Radiator Cap Pressure | |||
| 2.4L (AZ-FE) | 13.4 - 17.6 psi Minimum opening pressure 11.2 psi |
||
| 3.0L (1MZ-FE) | 12.1-16.4 psi Minimum opening pressure 10.0 psi |
||
| Thermostat R & I | |||
| 2.4L (AZ-FE) | THERMOSTAT | ||
| 3.0L (1MZ-FE) | THERMOSTAT | ||
| Water Pump R & I | |||
| 2.4L (AZ-FE) | WATER PUMP ASSEMBLY | ||
| 3.0L (1MZ-FE) | WATER PUMP | ||
| Engine Mechanical | |||
| Compression | ENGINE COMPRESSION | ||
| Oil Pressure | |||
| 2.4L (AZ-FE) | At normal operating temperature, oil pressure should be at least 4.3 psi (0.3 kg/cm2
) or more at idle. 36-78 psi (2.5-5.5 kg/cm2 ) or more at 3000 RPM. |
||
| 3.0L (1MZ-FE) | At normal operating temperature, oil pressure should be at least 4.3 psi (0.3 kg/cm2
) or more at idle. 43-78 psi (3.0-5.5 kg/cm2 ) or more at 3000 RPM. |
||
| Overhaul | |||
| 2.4L (AZ-FE) | ENGINE SPECIFICATIONS | ||
| 3.0L (1MZ-FE) | ENGINE SPECIFICATIONS | ||
| Torque | |||
| 2.4L (AZ-FE) | TORQUE SPECIFICATIONS | ||
| 3.0L (1MZ-FE) | TORQUE SPECIFICATIONS | ||
| Fluid Specifications | See FLUIDS under MAINTENANCE tab. | ||
| Flywheel/Flex Plate (Drive Plate) Torque | |||
| 2.4L (AZ-FE) | |||
| Drive plate & Ring gear (A/T) x Crankshaft | 72 ft.lbs (98 N.m) | ||
| Flywheel Sub-assy (M/T) x Crankshaft | 96 ft.lbs (130 N.m) | ||
| 3.0L (1MZ-FE) | 61 ft.lbs (83 N.m) | ||
| Fuel System | |||
| Pressure Specification | |||
| 2.4L (AZ-FE) | 44-50 psi (3.1-3.5 kg/cm2 ) | ||
| 3.0L (1MZ-FE) | 44-50 psi (3.1-3.5 kg/cm2 ) | ||
| Fuel Pressure Test Procedure | |||
| 2.4L (AZ-FE) | FUEL PRESSURE | ||
| 3.0L (1MZ-FE) | FUEL PRESSURE | ||
| Fuel Filter Locations | |||
| 4 Cyl | FUEL FILTER | ||
| V6 & V8 | FUEL FILTER | ||
| Ignition | |||
| Firing Order & Cylinder Identification | FIRING ORDER & CYLINDER IDENTIFICATION | ||
| Ignition Wires (Resistance) | HIGH TENSION WIRE RESISTANCE | ||
| Ignition Wires (Routing) | Refer to illustrations in FIRING ORDER & TIMING MARKS | ||
| Spark Plug | |||
| Type | SPARK PLUGS | ||
| Gap | SPARK PLUGS | ||
| Torque | SPARK PLUGS | ||
| Starting | |||
| Starter | STARTER SPECIFICATIONS | ||
| Torque | TORQUE SPECIFICATIONS | ||
| Wheel Alignment | |||
| Adjustment Specifications | SPECIFICATIONS | ||
| Torque Specifications | Refer to applicable components under PROCEDURES | ||
| Wheel & Tire | |||
| Wheel Lug Nut Torque | 76 ft.lbs (103 N.m) | ||