LEMON Manuals: Even more car manuals for everyone
Home >> Tesla >> 2024 >> Model Y Base >> Repair and Diagnosis >> Steering >> Steering Control Systems >> Steering -- Model Y >> Steering Rack And Lower Column >> Steering Rack (RWD) - Remove And Replace >> Remove

Steering Rack (RWD) - Remove And Replace: Remove

  1. Open the LH front door and fully lower the LH front window.
  2. Raise and support the vehicle. See RAISE VEHICLE - 2 POST LIFT .
  3. Set the steering wheel.

    LHD  - Set the steering wheel straight ahead.

    RHD  - Set the steering fully to the left.

    G14840940Courtesy of TESLA, INC.
  4. Using the steering wheel holder, lock the steering wheel into position.
    CAUTION: Protect the seat from damage.
    G14840941Courtesy of TESLA, INC.
  5. Remove the underhood storage unit. See UNDERHOOD STORAGE UNIT (REMOVE AND REPLACE) .
  6. Disconnect 12V power. See 12V/LV POWER (DISCONNECT AND CONNECT) .
  7. Remove the front wheels. See WHEEL (REMOVE AND INSTALL) .
  8. Remove the LH and RH tie rod ends. See TIE ROD END - LH (REMOVE AND REPLACE) .
  9. Remove the front aero shield panel. See Panel - Aero Shield - Front (Non-Structural Pack) - Remove And Replace .
  10. Remove the bolt that attaches the steering gear assembly to the intermediate shaft assembly.

    Tip: Use of the following tool(s) is recommended:

    • 13 mm socket
    G14840942Courtesy of TESLA, INC.
  11. Slide the electric steering column upward to remove it from the steering gear assembly.
    G14840943Courtesy of TESLA, INC.
  12. Release the connector locks, and then disconnect the logic connectors below the steering gear.
    CAUTION: DO NOT Push down on the red locking tab. Pull the tab away from the connector until the connector is unlocked, and then continue pulling to release the connector.
    G14840944Courtesy of TESLA, INC.
  13. Release the clips that attach the harness to the subframe assembly.
    G14840945Courtesy of TESLA, INC.
  14. Lower the vehicle so that the tires are just above the ground.
  15. Remove the bolts that attach the underhood storage unit reinforcement bracket to the vehicle, and then slide the bracket rearward for clearance.

    Tip: Use of the following tool(s) is recommended:

    • External Torx Plus EP14
    • Flex head ratchet/flex head torque wrench
    • 3 in extension
    G00649822Courtesy of TESLA, INC.
  16. RHD Vehicles Only  - Remove the bolts that attach the lower LH and RH of the cooling fan module to the front end carrier
    NOTE: With assistance, lift up on the cooling fan module to ease the removal of the bolts.
    G00649826Courtesy of TESLA, INC.
  17. Tip: Use of the following tool(s) is recommended:
  18. 8 mm socket
  19. Flex head ratchet/flex head torque wrench
  20. 4 in extension
  21. Use a bungee cord to position the fan assembly away from the steering gear.
    G14840951Courtesy of TESLA, INC.
  22. Release the connector locks, disconnect the steering gear assembly connectors, and then move the 12V steering gear harness aside for clearance.
    G14840947Courtesy of TESLA, INC.
  23. Remove the outer bolts that attach the steering gear assembly to the front subframe.

    Tip: Use of the following tool(s) is recommended:

    • 15 mm socket
    • Flex head ratchet/flex head torque wrench
    • 11 in extension
    G14840952Courtesy of TESLA, INC.
  24. Remove the inner bolts that attach the steering gear assembly to the front subframe.

    Tip: Use of the following tool(s) is recommended:

    • 18 mm swivel impact socket
    • Flex head ratchet/flex head torque wrench
    • 11 in extension
    G14840953Courtesy of TESLA, INC.
  25. Slide the steering gear assembly to the RH side of the vehicle to remove it through the underhood storage area.
    G14840954Courtesy of TESLA, INC.
    G14840955Courtesy of TESLA, INC.
scientia non olet · About LEMON Manuals