LEMON Manuals: Even more car manuals for everyone
Home >> Tesla >> 2024 >> Model 3 Base >> Repair and Diagnosis (Single Page) >> Accessories & Equipment >> Wiper/Washer Systems >> Electrical System (2 Of 2) -- Model 3 >> Keyless Entry and Security >> Passive Entry - Interior BLE Module - Remove And Replace >> Install

Passive Entry - Interior BLE Module - Remove And Replace: Install

  1. Seat the BLE module at the proper position, secure the clip, and then secure the bolt that attaches the BLE module to the vehicle.

    10 N.m (7.4 lbs-ft) 

    Tip: Use of the following tool(s) is recommended:

    • 10 mm socket
    • Ratchet/torque wrench
    • 4 in extension
    G16596383Courtesy of TESLA, INC.
    G16596384Courtesy of TESLA, INC.
  2. Engage the red locking tab to connect the connector.
    G16596385Courtesy of TESLA, INC.
  3. Align the locating pin of the front of the headliner to the slot, and then install the clips (x6) that attach the front of the headliner to vehicle.
    NOTE: Make sure that the door seal correctly overlaps the LH upper B-pillar trim.
    G16596386Courtesy of TESLA, INC.
    G16596387Courtesy of TESLA, INC.
    G16596388Courtesy of TESLA, INC.
    G16596389Courtesy of TESLA, INC.
  4. Install the rear view mirror. See REARVIEW MIRROR - REAR VIEW MIRROR, ASSEMBLY - REMOVE AND REPLACE .
  5. Install the lower camera cover. See REARVIEW MIRROR - REAR VIEW MIRROR, CAM LOWER COVER - REMOVE AND REPLACE .
  6. Install the LH sun visor. See SUN VISORS - SUN VISOR ASSEMBLY, LH - REMOVE AND REPLACE .
    WARNING: The video(s) included in this procedure are meant as an overview for supplemental purposes only. Follow all of the steps listed in the procedure to avoid damage to components and/or personal injury.
  7. Install the LH upper A-pillar trim. See A - B - C POST INTERIOR TRIM - A - PILLAR UPPER ASSEMBLY, LH - REMOVE AND REPLACE .
  8. Repeat step  7 and step  6 for the RH side of the vehicle.
  9. Connect the LV battery power. See LV BATTERY - LI-LON - DISCONNECT AND CONNECT .
  10. Move both front seats forward.
  11. Install the LH upper B-pillar trim. See A - B - C POST INTERIOR TRIM - B - PILLAR UPPER ASSEMBLY, LH - REMOVE AND REPLACE .
  12. Install the LH middle B-pillar trim. See TRIM - B-PILLAR - MIDDLE - LH - REMOVE AND REPLACE .
  13. Install the LH lower B-pillar trim. See A - B - C POST INTERIOR TRIM - B - PILLAR LOWER ASSEMBLY, LH - REMOVE AND REPLACE .
  14. Install the LH lower A-pillar trim. See A - B - C POST INTERIOR TRIM - A - PILLAR LOWER ASSEMBLY, LH - REMOVE AND REPLACE .
  15. Install the LH instrument panel end cap. See DASH PANEL - END CAP, LH - REMOVE AND REPLACE .
  16. Repeat step  11 through step  15 for the RH side of the vehicle.
  17. Install the 2nd row lower seat cushion. See 2ND ROW SEAT ASSEMBLIES - 2ND ROW SEAT CUSHION - REMOVE AND REPLACE .
  18. Install the 2nd row LH and RH seat side bolsters. See 2ND ROW SEAT ASSEMBLIES - 2ND ROW BOLSTER - LH - REMOVE AND REPLACE .
  19. Move both front seats back to the original position.
  20. Locally connect a laptop with Toolbox 3 to the vehicle. See TOOLBOX 3 - CONNECT AND DISCONNECT .
  21. On the laptop, select the Actions/Autodiag  tab and search for "Service_Redeploy". Select UPDATE_CAN-REDEPLOY(i) , click Run, and allow the routine to complete.
  22. On the touchscreen, verify that the release notes are present.
    NOTE: An error message will display on the touchscreen if the redeploy fails.
  23. Disable Service Mode. See SERVICE MODE .
  24. Place NFC Key cards (x2) on the top of the wireless charger pad.
    WARNING: Stacking a mobile phone and a NFC card in wireless charger may damage the card.
  25. On the laptop, select the Actions  tab and search for "Pair NFC". Select PROC_VCSEC_C_PAIR-NFC-CARD-V2(i) , click Run, add the number of cards to pair and click submit, and then allow the routine to complete.
  26. Make sure that the following functions of the programmed NFC keys work properly:
    • Using the NFC key to tap the driver side exterior B-pillar area locks/unlocks the vehicle.
    • Using the NFC key to tap the center console area behind the cup holders starts the vehicle.
  27. Disconnect the laptop with Toolbox 3 from the vehicle. See TOOLBOX 3 - CONNECT AND DISCONNECT .
  28. Raise all windows and close all doors.
scientia non olet · About LEMON Manuals