LEMON Manuals: Even more car manuals for everyone
Home >> Tesla >> 2020 >> Model S Long Range Plus >> Repair and Diagnosis (Single Page) >> Hybrid/Electric Powertrain >> Electric Motor Systems >> Front Drive Unit -- Model S >> Front Drive Unit Assembly >> Mount - Front Drive Unit - RH (1st Generation) - Remove And Replace >> Removal

Mount - Front Drive Unit - RH (1st Generation) - Remove And Replace: Removal

  1. Loosen the front RH wheel lug nuts (x5).
  2. Remove the HV battery HV Battery (RWD/AWD) (Remove And Install) .
  3. Remove the bolts (x2) that secure the coolant pump bracket to the body of the vehicle.
    G14982386Courtesy of TESLA, INC.
  4. Disconnect the electrical connector from the battery coolant pump.
  5. Carefully secure the coolant pump away from the working area.
  6. Lower the vehicle.
  7. Remove the 12V battery bracket beam 12V Battery Bracket Beam (Remove And Replace) .
  8. Release the fir tree clips (x2) that secure the 12V positive harness to the front cross car beam.
    G14982387Courtesy of TESLA, INC.
  9. Move the 12V positive harness to the RH side of the vehicle to keep it out of the working area.
    G14982388Courtesy of TESLA, INC.
  10. Release the bolts (x4) that secure the coolant reservoir to the cross car beam. Do not remove the reservoir at this time.
    G14982389Courtesy of TESLA, INC.
  11. Carefully lift up the coolant reservoir and disconnect the coolant level sensor harness.
    G14982390Courtesy of TESLA, INC.
  12. Remove the RH bolt that secures the A/C compressor bracket to the front drive unit.
    NOTE: This allows the jack strap to slide between the front drive unit and the compressor.
    G14982391Courtesy of TESLA, INC.
  13. Release the bolt that secures the coolant pump to the LH side of the front cross car beam.
    G14982392Courtesy of TESLA, INC.
  14. Remove the bolts (x4) that secure the front fuse boxes to the front shock tower crossmember. Move both fuse boxes behind the cross car beam.
  15. Position the support jack on top of the cross car beam and secure the screws (x2) to the cross car beam.
    NOTE: The support jack mounts to the bolt holes that secured the coolant reservoir.
    G14982393Courtesy of TESLA, INC.
  16. Fully lower both mounts of the support jack.
  17. Position the RH strap between the front drive unit and the A/C compressor:
    G14982394Courtesy of TESLA, INC.
    G14982395Courtesy of TESLA, INC.
    1. Lower one end of the strap over the top of the support jack and behind the front cross car beam.
    2. Reach beneath the drive unit and pull the strap upwards.
    3. Secure the two ends of the strap with the carabiner.
    4. Slide the strap so that the carabiner is approximately 6 inches (150 mm) above the front cross car beam.
  18. Raise both sides of the support jack alternately until the strap is fully taut.
    CAUTION: Even though only one strap is used in this procedure, it is important to raise both sides of the support jack.
  19. Raise the vehicle partially and remove the front RH wheel.
  20. Release the plastic rivets that secure the rear of the upper front arch liner and then pull the arch liner forward.
  21. Fully raise the vehicle.
  22. Remove and discard the upper forward bolt that secures the mount to the drive unit.
    G14982396Courtesy of TESLA, INC.
  23. Release the lower forward bolt that secures the mount to the drive unit.
    NOTE: The lower bolt cannot be completely removed at this time.
    G14982397Courtesy of TESLA, INC.
  24. Lower the vehicle.
  25. Release the edge clip that secures the coolant pump hose to the body of the vehicle. Move the coolant hose away from the working area.
  26. Working from the RH wheelwell, use a socket wrench with an extension to remove the bolts (x2) that secure the mount to the body.
    G14982398Courtesy of TESLA, INC.
    1. Remove the rear bolt and washer.
      G14982399Courtesy of TESLA, INC.
      G14982400Courtesy of TESLA, INC.
    2. Remove the front bolt.
      G14982401Courtesy of TESLA, INC.
  27. Remove and discard the upper rear bolt that secures the mount to the drive unit.
    G14982402Courtesy of TESLA, INC.
  28. Release the lower rear bolt that secures the mount to the drive unit.
    NOTE: The lower bolts (x2) cannot be completely removed from the mount at this time.
    G14982403Courtesy of TESLA, INC.
  29. Raise the vehicle.
  30. Remove the RH drive unit mount.
    NOTE: Maneuver the mount between the coolant hoses during removal.
  31. Remove and discard the lower bolts (x2) from the drive unit mount.
    G14982404Courtesy of TESLA, INC.
  32. If equipped, remove the shear plate from the drive unit mount.
scientia non olet · About LEMON Manuals