LEMON Manuals: Even more car manuals for everyone
Home >> Tesla >> 2014 >> Model S Base, AWD >> Repair and Diagnosis >> External Pages >> Different car >> Section 55 (Infotainment System -- Model S) >> Car Computer >> Car Computer - HW3 - Remove And Install >> Install

Car Computer - HW3 - Remove And Install: Install

WARNING: This page is about a different car, the 2024 Tesla Model S, 2023 Tesla Model S, 2022 Tesla Model S, and 2021 Tesla Model S. However, it is still accessible from the selected car via links, so may be relevant.
  1. Position the car computer into the vehicle, and then install the bolts (x2) and nut that attach the car computer to the vehicle.

    7 Nm (5.2 lbs-ft) 

    8 Nm (5.9 lbs-ft) 

    NOTE: The bolts are torqued to 7 Nm. The nut is torqued to 8 Nm.

    Tip: Use of the following tool(s) is recommended:

    • 10 mm socket
    G00644566Courtesy of TESLA INC
    G00644567Courtesy of TESLA INC
  2. Place coolant absorbent mats or rages around the car computer, remove the coolant plugs, and then secure the coolant hoses (x2) to the car computer coldplate assembly.
    NOTE: Perform a pull-push-pull test on each hose coupling.
    G00644568Courtesy of TESLA INC
  3. Remove the coolant hose clamps to the coldplate hoses (x2).
    NOTE: Place coolant absorbent mats or rags around the car computer. Clean any residual fluid and inspect for leaks.
    G00644569Courtesy of TESLA INC
    G00644570Courtesy of TESLA INC
    G00644571Courtesy of TESLA INC
  4. Connect the connectors (x3) at the RH side of the AP motherboard, and then secure the connector locks.
    G00644572Courtesy of TESLA INC
    G00644573Courtesy of TESLA INC
  5. Connect the connectors (x6) at the RH side of the entertainment motherboard, and then secure the connector locks.
    G00644574Courtesy of TESLA INC
    G00644575Courtesy of TESLA INC
  6. Connect the connectors (x7) at the LH side of the AP motherboard, and then secure the connector locks.
    G00644576Courtesy of TESLA INC
    G00644577Courtesy of TESLA INC
  7. Connect the connectors (x6) at the LH side of the entertainment motherboard, and then secure the connector locks.
    G00644578Courtesy of TESLA INC
    G00644579Courtesy of TESLA INC
  8. Connect the connector to the connectivity module, and then secure the connector lock.
    NOTE: Note Slide the lock underneath the connector.
    G00644580Courtesy of TESLA INC
    G00644581Courtesy of TESLA INC
  9. Connect the connector to the gaming MCU.
    NOTE: Make sure the connector is fully seated into the socket.
    G00644582Courtesy of TESLA INC
    G00644583Courtesy of TESLA INC
    G00644584Courtesy of TESLA INC
  10. Inspect the coolant bottle level and top off as necessary.
  11. Connect LV power. See LV Power - Disconnect And Connect .
  12. Perform a cooling system check and fill. See Cooling System - Partial Refill And Bleed .
  13. Install the rear underhood apron. See Underhood Apron - Rear (Remove and Replace) .
  14. Install the front passenger footrest panel. See Panel - Footrest - Front Passenger (LHD) - Remove And Replace .
  15. Install the passenger footwell cover. See Cover - Footwell - Passenger - Remove And Replace .
  16. Install the RH middle A-pillar trim. See Trim - A-Pillar - Middle - LH - Remove And Replace .
  17. Install the RH lower A-pillar trim. See Trim - A-Pillar - Lower - LH - Remove And Replace .
  18. Install the RH center console side panel carpet. See Carpet - Side Panel - Center Console - LH - Remove And Replace .
  19. Install the passenger footwell cover. See Cover - Footwell - Passenger - Remove And Replace .
  20. Move the front passenger seat back to its original position.
  21. Raise the front windows and close the front doors.
scientia non olet · About LEMON Manuals