LEMON Manuals: Even more car manuals for everyone
Home >> Tesla >> 2014 >> Model S Base, AWD >> Repair and Diagnosis >> External Pages >> Different car >> Section 52 (Electrical System (3 Of 3) -- Model S) >> Electronic Control Modules >> Module - Body Controller - Front - Remove And Replace >> Install

Module - Body Controller - Front - Remove And Replace: Install

WARNING: This page is about a different car, the 2024 Tesla Model S, 2023 Tesla Model S, 2022 Tesla Model S, and 2021 Tesla Model S. However, it is still accessible from the selected car via links, so may be relevant.
  1. Position the front body controller module for installation and secure the ground cable to the multi system beam.
    NOTE: 2x locating tabs, 1x ground cable
    G15091524Courtesy of TESLA, INC.
    G15091525Courtesy of TESLA, INC.
    G15091526Courtesy of TESLA, INC.
  2. Install the bolts (x3) that attach the front body controller module to the body.
    NOTE: 10 mm, 10 N.m. Start with the side bolt
    G15091527Courtesy of TESLA, INC.
  3. Install the bolt that attaches the ground cable for the front body controller module.
    NOTE: 10 mm, 10 N.m
    G15091528Courtesy of TESLA, INC.
  4. Secure the lower locking connectors (x2) on the front body controller module.
    NOTE: Engage red locking tab
    G15091529Courtesy of TESLA, INC.
    G15091530Courtesy of TESLA, INC.
    G15091531Courtesy of TESLA, INC.
  5. Secure the RH middle locking connectors (x2) on the front body controller module.
    NOTE: Verify that the yellow locking tabs are fully opened. Seat connectors and mechanism will begin to engage.
    G15091532Courtesy of TESLA, INC.
    G15091533Courtesy of TESLA, INC.
    G15091534Courtesy of TESLA, INC.
  6. Secure the LH locking connector for the front body controller module.
    NOTE: Verify the lever is fully opened. Seat connector and lever will begin to engage.
    G15091535Courtesy of TESLA, INC.
    G15091536Courtesy of TESLA, INC.
    G15091537Courtesy of TESLA, INC.
  7. Secure the upper locking connectors (x2) for the front body controller module.
    NOTE: Verify levers are fully opened. Seat connectors and levers will begin to engage.
    G15091538Courtesy of TESLA, INC.
    G15091539Courtesy of TESLA, INC.
    G15091540Courtesy of TESLA, INC.
  8. Connect LV power. See LV Power (Disconnect And Connect) .
  9. Connect Toolbox 3 to the vehicle. See Toolbox 3 (Connect and Disconnect) .
  10. In Toolbox, click Actions/Autodiag  , and then search for Service_Redeploy  .
  11. Click UPDATE_SERVICE-REDEPLOY  , and then click Run  . Allow the routine to complete.
    NOTE: Click X  at top right of window to close once the routine is complete.
  12. Adjust the headlights. See Headlights - Adjust (Wall Method)  or Headlights - Adjust - NA (Tool Method) .
  13. Install the underhood storage unit. See Underhood Storage Unit (Remove and Replace) .
  14. Install the underhood storage unit carpet.
    NOTE: Verify the carpet is properly seated under the seal.
    G15091541Courtesy of TESLA, INC.
    G15091542Courtesy of TESLA, INC.
  15. Install the underhood storage unit access panel. See Underhood Storage Unit Access Panel (Remove and Replace) .
  16. Install the front underhood apron. See Underhood Apron - Front (Remove and Replace) .
  17. Install the LH and RH underhood aprons. See Underhood Apron - LH (Remove and Replace) .
  18. Install the rear underhood apron. See Underhood Apron - Rear (Remove and Replace) .
scientia non olet · About LEMON Manuals