Fail-Safe Table

WARNING: This page is about a different variant/trim than selected.

This function is provided by the safe mechanism that assures safe driveability even when the solenoid valve, sensor or its circuit fails. The following table shows the fail-safe function for each fail condition of sensor, solenoid valve or its circuit.

SYMPTOM DIAGNOSIS DESCRIPTION CHART

DTC	DTC name	Fail-safe operation
P0602	Control Module Programming Error	-
P062F	Internal Control Module EEPROM Error	-
P0641	Sensor Reference Voltage "A" Circuit/Open	-
P0703	Brake Switch "B" Circuit	TCM controls actuators assuming that brake light switch is always on.
P0705	Transmission Range Sensor Circuit "A" (PRNDL Input)	TCM controls actuators assuming that select range is "D" range. TCM stops following operation/function. Lock-up control operation Manual shift mode function TCM transmits torque request signal to ECM (torque reduction). TCM transmits engine speed limit request signal to ECM.
P0707	Transmission Range Sensor "A" Circuit Low
P0711	Transmission Fluid Temperature Sensor "A" Circuit Range/Performance	TCM controls actuators assuming that CVT fluid temperature is specified value.
P0712	Transmission Fluid Temperature Sensor "A" Circuit Low
P0713	Transmission Fluid Temperature Sensor "A" Circuit High
P0716	Input/Turbine Speed Sensor "A" Circuit Range/Performance	TCM controls the actuator in presumption gear ratio calculated from secondary pulley speed and the stepper motor position. TCM inhibits following operation/function. Lock-up control operation Manual shift mode function TCM delays changing speed of gear ratio.
P0717	Input/Turbine Speed Sensor "A" Circuit No Signal
P0721	Output Speed Sensor Circuit Range/Performance	TCM controls the actuator by gear ratio depending on accelerator pedal position and primary pulley speed. TCM inhibits following operation/function. Lock-up control operation Manual shift mode function TCM delays changing speed of gear ratio.
P0722	Output Speed Sensor Circuit No Signal
P0741	Torque Converter Clutch Circuit Performance or Stuck Off	TCM stops lock-up control operation.
P0776	Pressure Control Solenoid "B" Performance/Stuck Off	-
P0777	Pressure Control Solenoid "B" Stuck On	TCM transmits torque request signal to ECM (torque reduction).
P0826	Manual mode Control Circuit	TCM stops manual shift mode.
P0842	Transmission Fluid Pressure Sensor/Switch "A" Circuit Low	TCM controls actuators assuming that line pressure is 0 MPa (0 kgf/cm² , 0 psi, 0 bar). TCM transmits torque request signal to ECM (torque reduction).
P0843	Transmission Fluid Pressure Sensor/Switch "A" Circuit High
P0847	Transmission Fluid Pressure Sensor/Switch "B" Circuit Low	TCM controls actuators assuming that secondary pressure is 0 MPa (0 kgf/cm² , 0 psi, 0 bar). TCM transmits torque request signal to ECM (torque reduction).
P0848	Transmission Fluid Pressure Sensor/Switch "B" Circuit High
P0871	Transmission Fluid Pressure Sensor/Switch "C" Circuit Range/Performance	TCM transmits torque request signal to ECM (torque reduction). Gear ratio is fixed at gear ratio of point that this DTC was detected.
P0961	Pressure Control Solenoid "A" Control Circuit Range/Performance	TCM transmits torque request signal to ECM (torque reduction). The following items are executed according to the detection frequency. TCM transmits torque request signal to ECM (torque reduction). TCM stops lock-up control. TCM limits shift speed of gear ratio. TCM controls gear ratio assuming that is specified value.
P0962	Pressure Control Solenoid "A" Control Circuit Low	TCM maximizes line pressure value (duty 0%).
P0963	Pressure Control Solenoid "A" Control Circuit High	TCM maximizes line pressure value (duty 0%).
P0966	Pressure Control Solenoid "B" Control Circuit Low	TCM maximizes secondary pressure value (duty 0%).
P0967	Pressure Control Solenoid "B" Control Circuit High	TCM maximizes secondary pressure value (duty 0%).
P1706	Torque Request Communication Error from TCM	-
P1810	Lockup/Select Control Circuit	TCM controls actuators assuming that lock-up/select switching solenoid valve is OFF.
P1816	Stepper Motor Circuit Malfunction	Gear ratio is fixed at gear ratio of point that this DTC was detected. TCM stops lock-up control.
P1818	Stepper Motor Performance	-
P1824	Calibration Data Reading Error	TCM controls the secondary pressure slightly higher than the specified value. TCM inhibits the display of shift position indicator in combination meter in "P" or "N" range. CM stops lock-up control.
P1825	TCM-Valve Body Assembly Correlation	TCM controls the secondary pressure slightly higher than the specified value.
P1970	Sensor Ground Circuit Malfunction	TCM stops following operation/function. Lock-up control operation Manual shift mode function TCM controls actuators assuming that CVT fluid temperature is specified value. TCM controls actuators assuming that line pressure is 0 MPa (0 kgf/cm² , 0 psi, 0 bar). TCM controls actuators assuming that secondary pressure is 0 MPa (0 kgf/cm² , 0 psi, 0 bar). TCM transmits torque request signal to ECM (torque reduction). Gear ratio is fixed at gear ratio of point that this DTC was detected.
P2763	Torque Converter Clutch Pressure Control Solenoid Control Circuit High	TCM stops lock-up operation.
P2764	Torque Converter Clutch Pressure Control Solenoid Control Circuit Low	TCM stops lock-up operation.
U0073	Control Module Communication Bus Off	-
U0100	Lost Communication With ECM	Engine speed is assumed to be specified value. Engine torque is assumed to be maximum value. TCM stops lock-up control. Throttle opening angle is assumed to be 0.0%.
U0121	Lost Communication With ABS	-
U0140	Lost Communication With BCM	-