LEMON Manuals: Even more car manuals for everyone
Home >> Suzuki >> 2012 >> SX4 Base >> Repair and Diagnosis >> Engine Performance >> System >> Engine General Information & Diagnosis >> Diagnostic Information and Procedures >> Fail-Safe Table >> Non-EVAP-Leak-Check Model

Non-EVAP-Leak-Check Model

DIAGNOSTIC INFORMATION AND PROCEDURES REFERENCE CHART

DTC DTC name Fail-safe operation
DTC P0010  "A" Camshaft Position Actuator Circuit/Open ECM stops A/F feedback (closed-loop) control.
P0011  "A" Camshaft Position-Timing Over-Advanced or System Performance
  • ECM controls OCV at engine brake.
  • ECM controls OCV at engine idle speed.
P0012  "A" Camshaft Position-Timing Over-Retarded -
P0031  HO2S Heater Control Circuit Low (Sensor-1) ECM stops A/F feedback (closed-loop) control.
P0032  HO2S Heater Control Circuit High (Sensor 1) ECM stops A/F feedback (closed-loop) control.
P0037  HO2S Heater Control Circuit Low (Sensor 2) ECM stops HO2S heater control.
P0038  HO2S Heater Control Circuit High (Sensor 2) ECM stops HO2S heater control.
P0101  Mass or Volume Air Flow "A" Circuit Range/Performance -
P0102  Mass or Volume Air Flow "A" Circuit Low
  • ECM calculates intake air volume according to throttle valve position and engine speed.
  • ECM stops A/F control.
  • ECM stops EVAP canister purge valve control.
P0103  Mass or Volume Air Flow "A" Circuit High
  • ECM calculates intake air volume according to throttle valve position and engine speed.
  • ECM stops A/F control.
  • ECM stops EVAP canister purge valve control.
P0111  Intake Air Temperature Sensor 1 Circuit Range/Performance -
P0112  Intake Air Temperature Sensor 1 Circuit Low
  • ECM controls actuators assuming that intake air temperature is 20°C (68°F).
  • ECM stops A/F feedback (closed-loop) control.
  • ECM stops IAC feedback control.
P0113  Intake Air Temperature Sensor 1 Circuit High
  • ECM controls actuators assuming that intake air temperature is 20°C (68°F).
  • ECM stops A/F feedback (closed-loop) control.
  • ECM stops IAC feedback control.
P0116  Engine Coolant Temperature Sensor 1 Circuit Range/Performance -
P0117  Engine Coolant Temperature Sensor 1 Circuit Low
  • ECM controls actuators assuming that engine coolant temperature is 80°C (176°F).
  • ECM operates radiator cooling fan. (high speed)
  • ECM stops A/F feedback (closed-loop) control.
  • ECM stops IAC feedback control.
  • ECM stops A/C control.
P0118  Engine Coolant Temperature Sensor 1 Circuit Low
  • ECM controls actuators assuming that engine coolant temperature is 80°C (176°F).
  • ECM operates radiator cooling fan. (high speed)
  • ECM stops A/F feedback (closed-loop) control.
  • ECM stops IAC feedback control.
  • ECM stops A/C control.
P0122  Throttle/Pedal Position Sensor/Switch "A" Circuit Low
  • ECM turns off throttle actuator control relay and throttle valve is fixed at the opening of about 7° from its completely closed position (default opening).
  • ECM controls fuel cut at specified engine speed.
  • ECM stops A/F feedback (closed-loop) control.
P0123  Throttle/Pedal Position Sensor/Switch "A" Circuit High
  • ECM turns off throttle actuator control relay and throttle valve is fixed at the opening of about 7° from its completely closed position (default opening).
  • ECM controls fuel cut at specified engine speed.
  • ECM stops A/F feedback (closed-loop) control.
P0131  O2 Sensor Circuit Low Voltage (Sensor 1)
  • ECM stops A/F feedback (closed-loop) control.
  • ECM stops EVAP canister purge valve control.
  • ECM stops A/F sensor heater control.
P0132  O2 Sensor Circuit High Voltage (Sensor 1)
  • ECM stops A/F feedback (closed-loop) control.
  • ECM stops EVAP canister purge valve control.
  • ECM stops A/F sensor heater control.
P0133  O2 Sensor Circuit Slow Response Sensor 1 -
P0134  O2 Sensor No Activity Detected (Sensor 1) ECM stops A/F feedback (closed-loop) control.
P0137  O2 Sensor Circuit Low Voltage (Sensor 2) -
P0138  O2 Sensor Circuit High Voltage (Sensor 2) -
P0171  System Too Lean ECM stops EVAP canister purge valve control.
P0172  System Too Rich ECM stops EVAP canister purge valve control.
P0222  Throttle/Pedal Position Sensor/Switch "B" Circuit Low
  • ECM turns off throttle actuator control relay and throttle valve is fixed at the opening of about 7° from its completely closed position (default opening).
  • ECM controls fuel cut at specified engine speed.
  • ECM stops air/fuel ratio feedback (closed-loop) control.
P0223  Throttle/Pedal Position Sensor/Switch "B" Circuit High
  • ECM turns off throttle actuator control relay and throttle valve is fixed at the opening of about 7° from its completely closed position (default opening).
  • ECM controls fuel cut at specified engine speed.
  • ECM stops air/fuel ratio feedback (closed-loop) control.
P0300  Random/Multiple Cylinder Misfire Detected ECM stops fuel injector control of malfunction cylinder.
P0301  Cylinder 1 Misfire Detected ECM stops fuel injector No. 1 control.
P0302  Cylinder 2 Misfire Detected ECM stops fuel injector No. 2 control.
P0303  Cylinder 3 Misfire Detected ECM stops fuel injector No. 3 control.
P0304  Cylinder 4 Misfire Detected ECM stops fuel injector No. 4 control.
P0327  Knock Sensor 1 Circuit Low
  • ECM stops knock control.
  • ECM controls fuel cut at specified engine speed.
P0328  Knock Sensor 1 Circuit High
  • ECM stops knock control.
  • ECM controls fuel cut at specified engine speed.
P0335  Crankshaft Position Sensor "A" Circuit
  • ECM controls ignition timing.
  • ECM controls fuel cut at specified engine speed.
P0340  Camshaft Position Sensor "A" Circuit
  • ECM controls ignition timing.
  • ECM stops knock control.
  • ECM controls fuel cut at specified engine speed.
P0420  Catalyst System Efficiency Below Threshold -
P0443  Evaporative Emission System Purge Control Valve Circuit -
P0480  Fan 1 Control Circuit -
P0481  Fan 2 Control Circuit -
P0482  Fan 3 Control Circuit -
P0500  Vehicle Speed Sensor "A"
  • ECM controls actuators assuming that vehicle speed is 0 km/h (0 mile/h).
  • ECM controls fuel cut at specified engine speed.
  • ECM stops cruise control system.
  • ECM stops IAC feedback control
P0504  Brake Switch "A"/"B" Correlation ECM stops cruise control system.
P0532  A/C Refrigerant Pressure Sensor "A" Circuit Low ECM stops A/C control.
P0533  A/C Refrigerant Pressure Sensor "A" Circuit High ECM stops A/C control.
P0560  System Voltage -
P0601  Internal Control Module Memory Check Sum Error -
P0602  Control Module Programming Error -
P0607  Control Module Performance
  • ECM turns off throttle actuator control relay and throttle valve is fixed at the opening of about 7° from its completely closed position (default opening).
  • ECM controls fuel cut at specified engine speed.
P0616  Starter Relay Circuit Low -
P0617  Starter Relay Circuit High -
P0620  Generator Control Circuit ECM stops generator control.
P0625  Generator Field/F Terminal Circuit Low ECM stops generator control.
P0626  Generator Field/F Terminal Circuit High ECM stops generator control.
P0660  Intake Manifold Tuning Valve Control Circuit/Open ECM stops IMT valve control.
P2101  Throttle Actuator "A" Control Motor Circuit Range/Performance
  • ECM turns off throttle actuator control relay and throttle valve is fixed at the opening of about 7° from its completely closed position (default opening).
  • ECM controls fuel cut at specified engine speed.
P2102  Throttle Actuator "A" Control Motor Circuit Low
  • ECM turns off throttle actuator control relay and throttle valve is fixed at the opening of about 7° from its completely closed position (default opening).
  • ECM controls fuel cut at specified engine speed.
P2103  Throttle Actuator "A" Control Motor Circuit High
  • ECM turns off throttle actuator control relay and throttle valve is fixed at the opening of about 7° from its completely closed position (default opening).
  • ECM controls fuel cut at specified engine speed.
P2111  Throttle Actuator Control System-Stuck Open
  • ECM turns off throttle actuator control relay and throttle valve is fixed at the opening of about 7° from its completely closed position (default opening).
  • ECM controls fuel cut at specified engine speed.
P2119  Throttle Actuator Control Throttle Body Range/Performance
  • ECM turns off throttle actuator control relay and throttle valve is fixed at the opening of about 7° from its completely closed position (default opening).
  • ECM controls fuel cut at specified engine speed.
P2122  Throttle/Pedal Position Sensor/Switch "D" Circuit Low
  • Lower upper limit of accelerator demand target throttle opening.
  • ECM controls fuel cut at specified engine speed.
P2123  Throttle/Pedal Position Sensor/Switch "D" Circuit High
  • Lower upper limit of accelerator demand target throttle opening.
  • ECM controls fuel cut at specified engine speed.
P2127  Throttle/Pedal Position Sensor/Switch "E" Circuit Low
  • Lower upper limit of accelerator demand target throttle opening.
  • ECM controls fuel cut at specified engine speed.
P2128  Throttle/Pedal Position Sensor/Switch "E" Circuit High
  • Lower upper limit of accelerator demand target throttle opening.
  • ECM controls fuel cut at specified engine speed.
P2135  Throttle/Pedal Position Sensor/Switch "A"/"B" Voltage Correlation
  • ECM turns off throttle actuator control relay and throttle valve is fixed at the opening of about 7° from its completely closed position (default opening).
  • ECM controls fuel cut at specified engine speed.
P2138  Throttle/Pedal Position Sensor/Switch "D"/"E" Voltage Correlation
  • ECM turns off throttle actuator control relay and throttle valve is fixed at the opening of about 7° from its completely closed position (default opening).
  • ECM controls fuel cut at specified engine speed.
P2195  O2 Sensor Signal Biased/Stuck Lean (Sensor 1) -
P2196  O2 Sensor Signal Biased/Stuck Rich (Sensor 1) -
P2227  Barometric Pressure Sensor "A" Circuit Range/Performance -
P2228  Barometric Pressure Sensor "A" Circuit Low ECM controls actuators assuming that barometric pressure is 101 kPa (760 mmHg).
P2229  Barometric Pressure Sensor "A" Circuit High ECM controls actuators assuming that barometric pressure is 101 kPa (760 mmHg).
P2237  O2 Sensor Positive Current Control Circuit/Open
  • ECM stops A/F feedback (closed-loop) control.
  • ECM stops EVAP canister purge valve control.
  • ECM stops A/F sensor heater control.
P2A01  O2 Sensor Circuit Range/Performance (Sensor 2) -
scientia non olet · About LEMON Manuals