Symptom Chart
WARNING: This page is about a different variant/trim than selected.
- The diagnostics item numbers show the sequence for inspection. Inspect in order from item 1.
- Overhaul and inspect inside the A/T only if A/T fluid condition is NG.
Refer to
[CHECKING THE A/T FLUID (ATF) ].SYMPTOM CHART
No. Items Symptom Condition Diagnostic Item 1 Shift Shock Large shock. ("N" → "D" position) Refer to [LARGE SHOCK ("N" TO "D" POSITION) ]. ON vehicle 1. Engine idle speed 2. Engine speed signal 3. Accelerator pedal position sensor 4. Control cable adjustment 5. ATF temperature sensor 6. Front brake solenoid valve 7. CAN communication line 8. Fluid level and state 9. Line pressure test 10. Control valve with TCM OFF vehicle 11. Forward brake (Parts behind drum support is impossible to perform inspection by disassembly. Refer to Cross-Sectional View .) 2 Shock is too large when changing D1 → D2 . ON vehicle 1. Accelerator pedal position sensor 2. Control cable adjustment 3. Direct clutch solenoid valve 4. CAN communication line 5. Engine speed signal 6. Turbine revolution sensor 7. Vehicle speed sensor A/T and vehicle speed sensor MTR 8. Fluid level and state 9. Control valve with TCM OFF vehicle 10. Direct clutch 3 Shock is too large when changing D2 → D3 . ON vehicle 1. Accelerator pedal position sensor 2. Control cable adjustment 3. High and low reverse clutch solenoid valve 4. CAN communication line 5. Engine speed signal 6. Turbine revolution sensor 7. Vehicle speed sensor A/T and vehicle speed sensor MTR 8. Fluid level and state 9. Control valve with TCM OFF vehicle 10. High and low reverse clutch 4 Shift Shock Shock is too large when changing D3 → D4 . ON vehicle 1. Accelerator pedal position sensor 2. Control cable adjustment 3. Input clutch solenoid valve 4. CAN communication line 5. Engine speed signal 6. Turbine revolution sensor 7. Vehicle speed sensor A/T and vehicle speed sensor MTR 8. Fluid level and state 9. Control valve with TCM OFF vehicle 10. Input clutch 5 Shock is too large when changing D4 → D5 . ON vehicle 1. Accelerator pedal position sensor 2. Control cable adjustment 3. Front brake solenoid valve 4. CAN communication line 5. Engine speed signal 6. Turbine revolution sensor 7. Vehicle speed sensor A/T and vehicle speed sensor MTR 8. Fluid level and state 9. Control valve with TCM OFF vehicle 10. Front brake (brake band) 11. Input clutch 6 Shock is too large for downshift when accelerator pedal is pressed. ON vehicle 1. Accelerator pedal position sensor 2. Control cable adjustment 3. CAN communication line 4. Engine speed signal 5. Turbine revolution sensor 6. Vehicle speed sensor A/T and vehicle speed sensor MTR 7. Fluid level and state 8. Control valve with TCM OFF vehicle 9. Front brake (brake band) 10. Input clutch 11. High and low reverse clutch 12. Direct clutch 7 Shift Shock Shock is too large for upshift when accelerator pedal is released. ON vehicle 1. Accelerator pedal position sensor 2. Control cable adjustment 3. Engine speed signal 4. CAN communication line 5. Turbine revolution sensor 6. Vehicle speed sensor A/T and vehicle speed sensor MTR 7. Fluid level and state 8. Control valve with TCM OFF vehicle 9. Front brake (brake band) 10. Input clutch 11. High and low reverse clutch 12. Direct clutch 8 Shock is too large for lock-up. ON vehicle 1. Accelerator pedal position sensor 2. Control cable adjustment 3. Engine speed signal 4. CAN communication line 5. Turbine revolution sensor 6. Vehicle speed sensor A/T and vehicle speed sensor MTR 7. Torque converter clutch solenoid valve 8. Fluid level and state 9. Control valve with TCM OFF vehicle 10. Torque converter 9 Shock is too large during engine brake. ON vehicle 1. Accelerator pedal position sensor 2. Control cable adjustment 3. CAN communication line 4. Fluid level and state 5. Control valve with TCM OFF vehicle 6. Front brake (brake band) 7. Input clutch 8. High and low reverse clutch 9. Direct clutch 10 No Up Shift Gear does not change from D1 → D2 .
Refer to [A/T DOES NOT SHIFT: D1 → D2 ].ON vehicle 1. Fluid level and state 2. Vehicle speed sensor A/T and vehicle speed sensor MTR 3. Direct clutch solenoid valve 4. Line pressure test 5. CAN communication line 6. Control valve with TCM OFF vehicle 7. Direct clutch 11 Gear does not change from D2 → D3 .
Refer to [A/T DOES NOT SHIFT: D2 → D3 ].ON vehicle 1. Fluid level and state 2. Vehicle speed sensor A/T and vehicle speed sensor MTR 3. High and low reverse clutch solenoid valve 4. Line pressure test 5. CAN communication line 6. Control valve with TCM OFF vehicle 7. High and low reverse clutch 12 Gear does not change from D3 → D4 .
Refer to [A/T DOES NOT SHIFT: D3 → D4 ].ON vehicle 1. Fluid level and state 2. Vehicle speed sensor A/T and vehicle speed sensor MTR 3. Input clutch solenoid valve 4. Front brake solenoid valve 5. Line pressure test 6. CAN communication line 7. Control valve with TCM OFF vehicle 8. Input clutch 13 Gear does not change from D4 → D5 .
Refer to [A/T DOES NOT SHIFT: D4 → D5 ].ON vehicle 1. Fluid level and state 2. Vehicle speed sensor A/T and vehicle speed sensor MTR 3. Front brake solenoid valve 4. Direct clutch solenoid valve 5. Turbine revolution sensor 6. Line pressure test 7. CAN communication line 8. Control valve with TCM OFF vehicle 9. Front brake (brake band) 10. Input clutch 14 No Down Shift In "D" range, does not downshift to 4th gear.
Refer to [A/T DOES NOT SHIFT: 5TH GEAR → 4TH GEAR ].ON vehicle 1. Fluid level and state 2. Vehicle speed sensor A/T and vehicle speed sensor MTR 3. Front brake solenoid valve 4. Direct clutch solenoid valve 5. CAN communication line 6. Line pressure test 7. Control valve with TCM OFF vehicle 8. Front brake (brake band) 9. Input clutch 15 In "D" or "3" range, does not downshift to 3rd gear.
Refer to [A/T DOES NOT SHIFT: 4TH GEAR → 3RD GEAR ].ON vehicle 1. Fluid level and state 2. Vehicle speed sensor A/T and vehicle speed sensor MTR 3. Input clutch solenoid valve 4. Front brake solenoid valve 5. CAN communication line 6. Line pressure test 7. Control valve with TCM OFF vehicle 8. Input clutch 16 In "D" or "2" range, does not downshift to 2nd gear.
Refer to [A/T DOES NOT SHIFT: 3RD GEAR → 2ND GEAR ].ON vehicle 1. Fluid level and state 2. Vehicle speed sensor A/T and vehicle speed sensor MTR 3. High and low reverse clutch solenoid valve 4. CAN communication line 5. Line pressure test 6. Control valve with TCM OFF vehicle 7. High and low reverse clutch 17 In "D" or "1" range, does not downshift to 1st gear.
Refer to [A/T DOES NOT SHIFT: 2ND GEAR → 1ST GEAR ].ON vehicle 1. Fluid level and state 2. Vehicle speed sensor A/T and vehicle speed sensor MTR 3. Direct clutch solenoid valve 4. CAN communication line 5. Line pressure test 6. Control valve with TCM OFF vehicle 7. Direct clutch 18 Slips/Will Not engage When "D" position, remains in 1st gear. ON vehicle 1. Fluid level and state 2. Vehicle speed sensor A/T and vehicle speed sensor MTR 3. Direct clutch solenoid valve 4. Line pressure test 5. CAN communication line 6. Control valve with TCM OFF vehicle 7. 3rd one-way clutch 8. 1st one-way clutch 9. Gear system 10. Reverse brake 11. Forward one-way clutch (Parts behind drum support is impossible to perform inspection by disassembly. Refer to Cross-Sectional View .) 12. Forward brake (Parts behind drum support is impossible to perform inspection by disassembly. Refer to Cross-Sectional View .) 19 When "D" position, remains in 2nd gear. ON vehicle 1. Fluid level and state 2. Vehicle speed sensor A/T and vehicle speed sensor MTR 3. Low coast brake solenoid valve 4. Line pressure test 5. CAN communication line 6. Control valve with TCM OFF vehicle 7. 3rd one-way clutch 8. Gear system 9. Direct clutch 10. Forward brake (Parts behind drum support is impossible to perform inspection by disassembly. Refer to Cross-Sectional View .) 20 Slips/Will Not engage When "D" position, remains in 3rd gear. ON vehicle 1. Fluid level and state 2. Vehicle speed sensor A/T and vehicle speed sensor MTR 3. Line pressure test 4. CAN communication line 5. Control valve with TCM OFF vehicle 6. 3rd one-way clutch 7. Gear system 8. High and low reverse clutch 9. Forward one-way clutch (Parts behind drum support is impossible to perform inspection by disassembly. Refer to Cross-Sectional View .) 10. Forward brake (Parts behind drum support is impossible to perform inspection by disassembly. Refer to Cross-Sectional View .) 21 When "D" position, remains in 4th gear. ON vehicle 1. Fluid level and state 2. Vehicle speed sensor A/T and vehicle speed sensor MTR 3. Input clutch solenoid valve 4. Direct clutch solenoid valve 5. High and low reverse clutch solenoid valve 6. Low coast brake solenoid valve 7. Front brake solenoid valve 8. Line pressure test 9. CAN communication line 10. Control valve with TCM OFF vehicle 11. Input clutch 12. Gear system 13. High and low reverse clutch 14. Direct clutch 22 Slips/Will Not Engage When "D" position, remains in 5th gear. ON vehicle 1. Fluid level and state 2. Vehicle speed sensor A/T and vehicle speed sensor MTR 3. Front brake solenoid valve 4. Line pressure test 5. CAN communication line 6. Control valve with TCM OFF vehicle 7. Front brake (brake band) 8. Input clutch 9. Gear system 10. High and low reverse clutch 23 Vehicle cannot be started from D1 .
Refer to [VEHICLE CANNOT BE STARTED FROM D1 ].ON vehicle 1. Fluid level and state 2. Accelerator pedal position sensor 3. Line pressure test 4. CAN communication line 5. Control valve with TCM OFF vehicle 6. Torque converter 7. Oil pump assembly 8. 3rd one-way clutch 9. 1st one-way clutch 10. Gear system 11. Reverse brake 12. Forward one-way clutch (Parts behind drum support is impossible to perform inspection by disassembly. Refer to Cross-Sectional View .) 13. Forward brake (Parts behind drum support is impossible to perform inspection by disassembly. Refer to Cross-Sectional View .) 24 Does not lockup.
Refer to [A/T DOES NOT PERFORM LOCK-UP ].ON vehicle 1. Fluid level and state 2. Line pressure test 3. Engine speed signal 4. Turbine revolution sensor 5. Torque converter clutch solenoid valve 6. CAN communication line 7. Control valve with TCM OFF vehicle 8. Torque converter 9. Oil pump assembly 25 Slips/Will Not engage Does not hold lock-up condition.
Refer to [A/T DOES NOT HOLD LOCK-UP CONDITION ].ON vehicle 1. Fluid level and state 2. Line pressure test 3. Engine speed signal 4. Turbine revolution sensor 5. Torque converter clutch solenoid valve 6. CAN communication line 7. Control valve with TCM OFF vehicle 8. Torque converter 9. Oil pump assembly 26 Lock-up is not released.
Refer to [LOCK-UP IS NOT RELEASED ].ON vehicle 1. Fluid level and state 2. Line pressure test 3. Engine speed signal 4. Turbine revolution sensor 5. Torque converter clutch solenoid valve 6. CAN communication line 7. Control valve with TCM OFF vehicle 8. Torque converter 9. Oil pump assembly 27 No shock at all or the clutch slips when vehicle changes speed D1 → D2 . ON vehicle 1. Fluid level and state 2. Vehicle speed sensor A/T and vehicle speed sensor MTR 3. Direct clutch solenoid valve 4. CAN communication line 5. Line pressure test 6. Control valve with TCM OFF vehicle 7. Torque converter 8. Oil pump assembly 9. 3rd one-way clutch 10. Gear system 11. Direct clutch 12. Forward brake (Parts behind drum support is impossible to perform inspection by disassembly. Refer to Cross-Sectional View .) 28 Slips/Will Not engage No shock at all or the clutch slips when vehicle changes speed D2 → D3 . ON vehicle 1. Fluid level and state 2. Vehicle speed sensor A/T and vehicle speed sensor MTR 3. High and low reverse clutch solenoid valve 4. CAN communication line 5. Line pressure test 6. Control valve with TCM OFF vehicle 7. Torque converter 8. Oil pump assembly 9. 3rd one-way clutch 10. Gear system 11. High and low reverse clutch 12. Forward one- way clutch (Parts behind drum support is impossible to perform inspection by disassembly. Refer to Cross-Sectional View .) 13. Forward brake (Parts behind drum support is impossible to perform inspection by disassembly. Refer to Cross-Sectional View .) 29 No shock at all or the clutch slips when vehicle changes speed D3 → D4 . ON vehicle 1. Fluid level and state 2. Vehicle speed sensor A/T and vehicle speed sensor MTR 3. Input clutch solenoid valve 4. Front brake solenoid valve 5. CAN communication line 6. Line pressure test 7. Control valve with TCM OFF vehicle 8. Torque converter 9. Oil pump assembly 10. Input clutch 11. Gear system 12. High and low reverse clutch 13. Direct clutch 30 Slips/Will Not engage No shock at all or the clutch slips when vehicle changes speed D4 → D5 . ON vehicle 1. Fluid level and state 2. Vehicle speed sensor A/T and vehicle speed sensor MTR 3. Front brake solenoid valve 4. Direct clutch solenoid valve 5. CAN communication line 6. Line pressure test 7. Control valve with TCM OFF vehicle 8. Torque converter 9. Oil pump assembly 10. Front brake (brake band) 11. Input clutch 12. Gear system 13. High and low reverse clutch 31 When you press the accelerator pedal and shift speed D5 → D4 , the engine idles or the transmission slips. ON vehicle 1. Fluid level and state 2. Vehicle speed sensor A/T and vehicle speed sensor MTR 3. Front brake solenoid valve 4. Direct clutch solenoid valve 5. CAN communication line 6. Line pressure test 7. Control valve with TCM OFF vehicle 8. Torque converter 9. Oil pump assembly 10. Input clutch 11. Gear system 12. High and low reverse clutch 13. Direct clutch 32 Slips/Will Not engage When you press the accelerator pedal and shift speed D4 → D3 , the engine idles or the transmission slips. ON vehicle 1. Fluid level and state 2. Vehicle speed sensor A/T and vehicle speed sensor MTR 3. Input clutch solenoid valve 4. Front brake solenoid valve 5. CAN communication line 6. Line pressure test 7. Control valve with TCM OFF vehicle 8. Torque converter 9. Oil pump assembly 10. 3rd one-way clutch 11. Gear system 12. High and low reverse clutch 13. Forward one- way clutch (Parts behind drum support is impossible to perform inspection by disassembly. Refer to Cross-Sectional View .) 14. Forward brake (Parts behind drum support is impossible to perform inspection by disassembly. Refer to Cross-Sectional View .) 33 When you press the accelerator pedal and shift speed D3 → D2 , the engine idles or the transmission slips. ON vehicle 1. Fluid level and state 2. Vehicle speed sensor A/T and vehicle speed sensor MTR 3. High and low reverse clutch solenoid valve 4. Direct clutch solenoid valve 5. CAN communication line 6. Line pressure test 7. Control valve with TCM OFF vehicle 8. Torque converter 9. Oil pump assembly 10. 3rd one-way clutch 11. Gear system 12. Direct clutch 13. Forward brake (Parts behind drum support is impossible to perform inspection by disassembly. Refer to Cross-Sectional View .) 34 Slips/Will Not Engage When you press the accelerator pedal and shift speed D2 → D1 , the engine idles or the transmission slips. ON vehicle 1. Fluid level and state 2. Vehicle speed sensor A/T and vehicle speed sensor MTR 3. Direct clutch solenoid valve 4. CAN communication line 5. Line pressure test 6. Control valve with TCM OFF vehicle 7. Torque converter 8. Oil pump assembly 9. 3rd one-way clutch 10. 1st one-way clutch 11. Gear system 12. Reverse brake 13. Forward one- way clutch (Parts behind drum support is impossible to perform inspection by disassembly. Refer to Cross-Sectional View .) 14. Forward brake (Parts behind drum support is impossible to perform inspection by disassembly. Refer to Cross-Sectional View .) 35 With selector lever in "D" position, acceleration is extremely poor. ON vehicle 1. Fluid level and state 2. Line pressure test 3. Accelerator pedal position sensor 4. CAN communication line 5. PNP switch 6. Control cable adjustment 7. Control valve with TCM OFF vehicle 8. Torque converter 9. Oil pump assembly 10. 1st one-way clutch 11. Gear system 12. Reverse brake 13. Forward one- way clutch (Parts behind drum support is impossible to perform inspection by disassembly. Refer to Cross-Sectional View .) 14. Forward brake (Parts behind drum support is impossible to perform inspection by disassembly. Refer to Cross-Sectional View .) 36 Slips/Will Not Engage With selector lever in "R" position, acceleration is extremely poor. ON vehicle 1. Fluid level and state 2. Line pressure test 3. Accelerator pedal position sensor 4. High and low reverse clutch solenoid valve 5. CAN communication line 6. PNP switch 7. Control cable adjustment 8. Control valve with TCM OFF vehicle 9. Gear system 10. Output shaft 11. Reverse brake 37 While starting off by accelerating in 1st, engine races or slippage occurs. ON vehicle 1. Fluid level and state 2. Line pressure test 3. Accelerator pedal position sensor 4. CAN communication line 5. Control valve with TCM OFF vehicle 6. Torque converter 7. Oil pump assembly 8. 3rd one-way clutch 9. 1st one-way clutch 10. Gear system 11. Reverse brake 12. Forward one- way clutch (Parts behind drum support is impossible to perform inspection by disassembly. Refer to Cross-Sectional View .) 13. Forward brake (Parts behind drum support is impossible to perform inspection by disassembly. Refer to Cross-Sectional View .) 38 While accelerating in 2nd, engine races or slippage occurs. ON vehicle 1. Fluid level and state 2. Line pressure test 3. Accelerator pedal position sensor 4. CAN communication line 5. Direct clutch solenoid valve 6. Control valve with TCM OFF vehicle 7. Torque converter 8. Oil pump assembly 9. 3rd one-way clutch 10. Gear system 11. Direct clutch 12. Forward brake (Parts behind drum support is impossible to perform inspection by disassembly. Refer to Cross-Sectional View .) 39 Slips/Will Not Engage While accelerating in 3rd, engine races or slippage occurs. ON vehicle 1. Fluid level and state 2. Line pressure test 3. Accelerator pedal position sensor 4. CAN communication line 5. High and low reverse clutch solenoid valve 6. Control valve with TCM OFF vehicle 7. Torque converter 8. Oil pump assembly 9. 3rd one-way clutch 10. Gear system 11. High and low reverse clutch 12. Forward one- way clutch (Parts behind drum support is impossible to perform inspection by disassembly. Refer to Cross-Sectional View .) 13. Forward brake (Parts behind drum support is impossible to perform inspection by disassembly. Refer to Cross-Sectional View .) 40 While accelerating in 4th, engine races or slippage occurs. ON vehicle 1. Fluid level and state 2. Line pressure test 3. Accelerator pedal position sensor 4. CAN communication line 5. Input clutch solenoid valve 6. Control valve with TCM OFF vehicle 7. Torque converter 8. Oil pump assembly 9. Input clutch 10. Gear system 11. High and low reverse clutch 12. Direct clutch 41 Slips/Will Not Engage While accelerating in 5th, engine races or slippage occurs. ON vehicle 1. Fluid level and state 2. Line pressure test 3. Accelerator pedal position sensor 4. CAN communication line 5. Front brake solenoid valve 6. Control valve with TCM OFF vehicle 7. Torque converter 8. Oil pump assembly 9. Front brake (brake band) 10. Input clutch 11. Gear system 12. High and low reverse clutch 42 Slips at lock-up. ON vehicle 1. Fluid level and state 2. Line pressure test 3. Engine speed signal 4. Turbine revolution sensor 5. Torque converter clutch solenoid valve 6. CAN communication line 7. Control valve with TCM OFF vehicle 8. Torque converter 9. Oil pump assembly 43 No creep at all. Refer to [VEHICLE DOES NOT CREEP BACKWARD IN "R" POSITION ], [VEHICLE DOES NOT CREEP FORWARD IN "D" POSITION ] ON vehicle 1. Fluid level and state 2. Line pressure test 3. Accelerator pedal position sensor 4. Direct clutch solenoid valve 5. PNP switch 6. CAN communication line 7. Control cable adjustment 8. Control valve with TCM OFF vehicle 9. Torque converter 10. Oil pump assembly 11. 1st one-way clutch 12. Gear system 13. Reverse brake 14. Direct clutch 15. Forward one- way clutch (Parts behind drum support is impossible to perform inspection by disassembly. Refer to Cross-Sectional View .) 16. Forward brake (Parts behind drum support is impossible to perform inspection by disassembly. Refer to Cross-Sectional View .) 44 Slips/Will Not Engage Vehicle cannot run in all positions. ON vehicle 1. Fluid level and state 2. Line pressure test 3. PNP switch 4. Control cable adjustment 5. Control valve with TCM OFF vehicle 6. Oil pump assembly 7. Gear system 8. Output shaft 45 With selector lever in "D" position, driving is not possible. ON vehicle 1. Fluid level and state 2. Line pressure test 3. PNP switch 4. Control cable adjustment 5. Control valve with TCM OFF vehicle 6. Torque converter 7. Oil pump assembly 8. 1st one-way clutch 9. Gear system 10. Reverse brake 11. Forward one- way clutch (Parts behind drum support is impossible to perform inspection by disassembly. Refer to Cross-Sectional View .) 12. Forward brake (Parts behind drum support is impossible to perform inspection by disassembly. Refer to Cross-Sectional View .) 46 With selector lever in "R" position, driving is not possible. ON vehicle 1. Fluid level and state 2. Line pressure test 3. PNP switch 4. Control cable adjustment 5. Control valve with TCM OFF vehicle 6. Gear system 7. Output shaft 8. Reverse brake 47 Others Shift point is high in "D" position. ON vehicle 1. Vehicle speed sensor A/T and vehicle speed sensor MTR 2. Accelerator pedal position sensor 3. CAN communication line 4. ATF temperature sensor 5. Control valve with TCM 48 Others Shift point is low in "D" position. ON vehicle 1. Vehicle speed sensor A/T and vehicle speed sensor MTR 2. Accelerator pedal position sensor 3. CAN communication line 4. Control valve with TCM 49 Judder occurs during lock-up. ON vehicle 1. Fluid level and state 2. Engine speed signal 3. Turbine revolution sensor 4. Vehicle speed sensor A/T and vehicle speed sensor MTR 5. Accelerator pedal position sensor 6. CAN communication line 7. Torque converter clutch solenoid valve 8. Control valve with TCM OFF vehicle 9. Torque converter 50 Strange noise in "R" position. ON vehicle 1. Fluid level and state 2. Engine speed signal 3. CAN communication line 4. Control valve with TCM OFF vehicle 5. Torque converter 6. Oil pump assembly 7. Gear system 8. High and low reverse clutch 9. Reverse brake 51 Strange noise in "N" position. ON vehicle 1. Fluid level and state 2. Engine speed signal 3. CAN communication line 4. Control valve with TCM OFF vehicle 5. Torque converter 6. Oil pump assembly 7. Gear system 52 Strange noise in "D" position. ON vehicle 1. Fluid level and state 2. Engine speed signal 3. CAN communication line 4. Control valve with TCM OFF vehicle 5. Torque converter 6. Oil pump assembly 7. Gear system 8. Forward brake (Parts behind drum support is impossible to perform inspection by disassembly. Refer to Cross-Sectional View .) 53 Others Vehicle does not decelerate by engine brake. Refer to [VEHICLE DOES NOT DECELERATE BY ENGINE BRAKE ]. ON vehicle 1. PNP switch 2. Fluid level and state 3. Control cable adjustment 4. 1st position switch 5. CAN communication line 6. Control valve with TCM OFF vehicle 7. Input clutch 8. High and low reverse clutch 9. Direct clutch 54 Engine brake does not operate in "2" position. ON vehicle 1. PNP switch 2. Fluid level and state 3. Control cable adjustment 4. CAN communication line 5. Control valve with TCM OFF vehicle 6. Front brake (brake band) 7. Input clutch 8. High and low reverse clutch 55 Engine brake does not operate in "1" position. ON vehicle 1. PNP switch 2. Fluid level and state 3. Control cable adjustment 4. 1st position switch 5. CAN communication line 6. Control valve with TCM OFF vehicle 7. Input clutch 8. High and low reverse clutch 9. Direct clutch 56 Others Maximum speed low. ON vehicle 1. Fluid level and state 2. Line pressure test 3. Accelerator pedal position sensor 4. CAN communication line 5. Direct clutch solenoid valve 6. Control valve with TCM OFF vehicle 7. Torque converter 8. Oil pump assembly 9. Input clutch 10. Gear system 11. High and low reverse clutch 12. Direct clutch 13. Forward one- way clutch (Parts behind drum support is impossible to perform inspection by disassembly. Refer to Cross-Sectional View .) 14 Forward brake (Parts behind drum support is impossible to perform inspection by disassembly. Refer to Cross-Sectional View .) 57 Extremely large creep. ON vehicle 1. Engine idle speed 2. CAN communication line OFF vehicle 3. Torque converter 58 With selector lever in "P" position, vehicle does not enter parking condition or, with selector lever in another position, parking condition is not cancelled. Refer to [IN "P" POSITION, VEHICLE MOVES WHEN PUSHED ]. ON vehicle 1. PNP switch 2. Control cable adjustment OFF vehicle 3. Parking pawl components 59 Vehicle runs with transmission in "P" position. ON vehicle 1. PNP switch 2. Fluid level and state 3. Control cable adjustment 4. Control valve with TCM 5. Parking pawl components OFF vehicle 6. Gear system 60 Others Vehicle runs with transmission in "N" position. Refer to [IN "N" POSITION, VEHICLE MOVES ]. ON vehicle 1. PNP switch 2. Fluid level and state 3. Control cable adjustment 4. Control valve with TCM OFF vehicle 5. Input clutch 6. Gear system 7. Direct clutch 8. Reverse brake 9. Forward one- way clutch (Parts behind drum support is impossible to perform inspection by disassembly. Refer to Cross-Sectional View .) 10. Forward brake (Parts behind drum support is impossible to perform inspection by disassembly. Refer to Cross-Sectional View .) 61 Engine does not start in "N" or "P" position. Refer to [ENGINE CANNOT BE STARTED IN "P" OR "N" POSITION ]. ON vehicle 1. Ignition switch and starter 2. Control cable adjustment 3. PNP switch 62 Engine starts in positions other than "N" or "P". ON vehicle 1. Ignition switch and starter 2. Control cable adjustment 3. PNP switch 63 Engine stall. ON vehicle 1. Fluid level and state 2. Engine speed signal 3. Turbine revolution sensor 4. Torque converter clutch solenoid valve 5. CAN communication line 6. Control valve with TCM OFF vehicle 7. Torque converter 64 Engine stalls when select lever shifted "N" → "D", "R". ON vehicle 1. Fluid level and state 2. Engine speed signal 3. Turbine revolution sensor 4. Torque converter clutch solenoid valve 5. CAN communication line 6. Control valve with TCM OFF vehicle 7. Torque converter 65 Others Engine speed does not return to idle. Refer to [ENGINE SPEED DOES NOT RETURN TO IDLE ]. ON vehicle 1. Fluid level and state 2. Direct clutch solenoid valve 3. Front brake solenoid valve 4. Accelerator pedal position sensor 5. Vehicle speed sensor A/T and vehicle speed sensor MTR 6. CAN communication line 7. Control valve with TCM OFF vehicle 8. Front brake (brake band) 9. Direct clutch