Values On the Diagnosis Tool
WARNING: This page is about a different variant/trim than selected.
NOTE:
- The SDT electrically displays shift timing and lock-up timing (that is, operation timing of each solenoid). Check for time difference between actual shift timing and the SDT display. If the difference is noticeable, mechanical parts (except solenoids, sensors, etc.) may be malfunctioning. Check mechanical parts using applicable diagnostic procedures.
- Shift schedule (which implies gear position) displayed on SDT and that indicated in Service Information may differ slightly. This occurs because of the following reasons:
- Actual shift schedule has more or less tolerance or allowance
- Shift schedule indicated in Service Information refers to the point where shifts start, and
- Gear position displayed on SDT indicates the point where shifts are completed.
- Display of solenoid valves on SDT changes at the start of shifting, while gear position is displayed upon completion of shifting (which is computed by TCM).
DIAGNOSIS TOOL REFERENCE VALUE
| Item name | Condition | Display value (Approx.) |
|---|---|---|
| ATF TEMP SE 1 | 0 °C (32 ° F) - 20 °C (68 °F) - 80 °C (176 °F) | 3.3 - 2.7 - 0.9 V |
| TCC SOLENOID | When perform slip lock-up | 0.2 - 0.4 A |
| When perform lock-up | 0.4 - 0.6 A | |
| SLCT LVR POSI | Selector lever in "N", "P" positions. | N/P |
| Selector lever in "R" position. | R | |
| Selector lever in "D" position. | D | |
| Selector lever in "3" position. | 3 | |
| Selector lever in "2" position. | 2 | |
| Selector lever in "1" position. | 1 | |
| VHCL/S SE-A/T | During driving | Approximately matches the speedometer reading. |
| ENGINE SPEED | Engine running | Closely matches the tachometer reading. |
| LINE PRES SOL | During driving | 0.2 - 0.6 A |
| INPUT SPEED | During driving (lock-up ON) | Approximately matches the engine speed. |
| VHCL/S SE-MTR | During driving | Approximately matches the speedometer reading. |
| ATF PRES SW 2 | Low coast brake engaged. Refer to A/T Control System: Shift Mechanism | ON |
| Low coast brake disengaged. Refer to A/T Control System: Shift Mechanism | OFF | |
| I/C SOLENOID | Input clutch disengaged. Refer to A/T Control System: Shift Mechanism | 0.6 - 0.8 A |
| Input clutch engaged. Refer to A/T Control System: Shift Mechanism | 0 - 0.05 A | |
| FR/B SOLENOID | Front brake engaged. Refer to A/T Control System: Shift Mechanism | 0.6 - 0.8 A |
| Front brake disengaged. Refer to A/T Control System: Shift Mechanism | 0 - 0.05 A | |
| D/C SOLENOID | Direct clutch disengaged. Refer to A/T Control System: Shift Mechanism | 0.6 - 0.8 A |
| Direct clutch engaged. Refer to A/T Control System: Shift Mechanism | 0 - 0.05 A | |
| HLR/C SOL | High and low reverse clutch disengaged. Refer to A/T Control System: Shift Mechanism | 0.6 - 0.8 A |
| High and low reverse clutch engaged. Refer to A/T Control System: Shift Mechanism | 0 - 0.05 A | |
| ON OFF SOL | Low coast brake engaged. Refer to A/T Control System: Shift Mechanism | ON |
| Low coast brake disengaged. Refer to A/T Control System: Shift Mechanism | OFF | |
| STARTER RELAY | Selector lever in "N", "P" positions. | ON |
| Selector lever in other position | OFF | |
| ACCELE POSI | Released accelerator pedal | 0.0/8 |
| Fully depressed accelerator pedal | 8/8 | |
| CLSD THL POS | Released accelerator pedal | ON |
| Fully depressed accelerator pedal | OFF | |
| W/O THL POS | Fully depressed accelerator pedal. | ON |
| Released accelerator pedal. | OFF | |
| OD CONT SW | Releasing overdrive control switch | OFF |
| Holding overdrive control switch | ON | |
| 1 POSITION SW | When setting selector lever to "1" position | ON |
| When setting selector lever to other positions. | OFF | |
| BRAKESW | Depressed brake pedal | ON |
| Released brake pedal. | OFF |